How to Repair the Pull Cord for Blinds. Step 1. Remove the cap covering the hole in the bottom rail of the venetian blinds. You can do this with your hands and fingers. Look for the end of ... Step 2. Step 3. Step 4. Replace a Pull Cord.
How do I replace the cord on my blinds?
These buttons hold the ladder tape in place and cover up the knot of the cord. They vary depending on your model of blind. Pull the knot out and clip it off. Do this for all runs of cord. You can then pull all the old cord out. Use the lighter to seal one end of your new cord. Start at the run furthest from the little locking mechanism.
Why do pull cords come apart on blinds?
During the operation of the blinds, pull cords are used almost at a daily basis. This is why pull cords come apart or simply snap. If you have pets, these cords are likely to get more than their fair share of attention. However, it would be a shame if a perfectly find blind has to be written off just for a damaged pull cord.
How much cord do I need to pull up blinds?
Most places carry stock cord in white, beige and brown. For pleated shades, select lift cord that’s .9 mm thick; for vinyl miniblinds, 1.4 mm; for wood slat blinds, 1.8 mm. Cord is inexpensive. To figure how much blind pull cord you’ll need, multiply the height of your extended blinds by 4 and add the width.
How to melt a cord?
Hold the end of the new cord in your hand. Light a lighter, and catch the end of the new cord on fire. Immediately blow out the flame. Attach the old cord and new cord together. This will melt the ends of the cords together.
How to bond cords?
Carefully, roll the hot, melted ends together between your fingertips to bond the cords together. Press gently so you don't burn yourself. When the ends are bonded after a minute or so , gently tug on the cord connection to ensure that the ends are bonded securely. If not, repeat the lighting procedure.
Can you replace a pull cord on venetian blinds?
Venetian blinds. Sometimes a pull cord for a blind gets stuck, needing repair--or breaks, requiring replacement. You can purchase replacement cords for your blinds from companies over the Internet or at your local hardware or building-supply store. Different-size blinds require specific cord widths; and since different styles ...
How to keep a cord from slipping?
The locking mechanism should keep the cord from slipping back. Make sure you have enough to tie a large knot at the end and then cut the tail, sealing the ends. Tie a regular square knot in the tail close to the end and stuff it and the excess ladder tape back in the hole and pop the button back in.
What to do with old cords?
Use the ones from your old cords. If you lost them, you can use pretty beads or decorative knots or a combination of these . They add weight to the bottom of the cords so that they hang right and provide a grip for pulling. Scissors.
Can cats chew on horizontal blinds?
If you live with a cat, chances are the cords on your horizontal blinds have been used as a chew toy. This damage may even have rendered your blinds unusable as either the cords are now too short or there are knots that block it. I had five sets of blinds with this problem and set out to fix them rather than having to buy new ones.
Replace old cords easily and quickly before they break
Replace worn cords on miniblinds, pleated shades and other slatted blinds before they fall apart. Use our quick restringing system to simplify the task of how to fix blinds.
Step 1: Evaluate your blind and buy new blind pull cord
No need to go out and buy new blinds! We’ll show you how to fix blinds with a few simple steps. The best time to replace the lift cord that raises and lowers a miniblind is when you first notice it’s frayed—don’t wait till it breaks.
Step 2: Replace the cord
Open the support brackets, remove the blind and take it to a workbench for splicing the frayed section of lift cord to a new cord.
Required Tools for this Project
Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.
What to do if your vertical blind cord is broken?
Emery board. Paint that matches the color of your vertical blind’s cord. Repair your vertical blind's cord. If your vertical blind's cord is broken on an area that you can access easily, you can repair it yourself.
How to cut a cord that is torn?
Take the scissors and snip off the ends of the cord where the cord is torn. You only need to snip off enough to give the cord a clean cut with an even end.
How to stop vertical blinds from sticking?
Open and close the vertical blind slowly with the cord to make sure that it's working properly. Sand the cord again with the emery board if your vertical blind is sticking or stopping when opening or closing the blind.
How to make a twig out of cord?
Take the other end of the cord and press it straight into the part of the cord that you have just melted. Be careful not to burn your fingers. Only press it together just enough to melt it together. Hold it in place until it cools. Tug lightly on the cord to make sure that it has bonded together.
How to burn a cord?
Hold one end of the cord in one hand. Make sure you are not holding too close to the end of the cord since you will be holding the cord over a fire. Strike the lighter with your other hand and carefully hold the lighter under the end of the cord only until it starts to melt. Do not let the cord catch on fire. If the cord catches on fire, immediately blow out the flame, snip off the end of the cord again, and start over.