How to fix a lawnmower pull cord that is stuck, step by step
- To start, inspect your blade for any stuck strands of grass or debris. Remove them as they cause the pull cord to get stuck.
- Open the blower housing and inspect the recoil starter. If it appears damaged, you need to replace it.
- Check if the engine is hydro-locked, remove the spark plug and pull the rope repeatedly to restart the engine.
Full Answer
How to fix pull string on lawn mower?
How to fix a lawnmower pull cord that is stuck, step by step: Step 1: To start, inspect your blade for any stuck strands of grass or debris. Remove them as they cause the pull cord to get stuck. Step 2: Open the blower housing and inspect the recoil starter. If it appears damaged, you need to replace it.
How to replace a lawnmower pull cord?
Replacing a lawnmower pull cord, step-by-step:
- Gather the tools and correct replacement cord. Before we can remove the pull cord, you need to ensure that you have the equipment and materials required for the ...
- Unscrew the starter setup. The pull cord is attached to the lawnmower’s starter disk. ...
- Remove the pull rope. ...
- Replace the old pull string with the new one. ...
How to fix mower starter rope Briggs lawnmower pull cord?
Tie a Knot
- Put the handle on the rope and tie a knot. ...
- If the rope on your lawn mower extends up the handle, make sure to place the rope handle in its final position before tensioning the rope slightly and tying the ...
- Let the pulley wind the rope back into the rewind.
- Reinstall the rewind unit and any other parts you've removed.
Should I repair or replace my lawn mower?
How to Know When It's Time to Replace Your Lawn Mower
- Cover your bases... This should always be your approach, Kiser says; he recommends checking and replacing the air filter, oil, and gasoline before jumping to any conclusions.
- Don't let gasoline sit in the machine. ...
- Replace dull blades. ...
- Check the belt. ...
- Consider the bottom line. ...
How do I fix the pull cord on my lawn mower?
2:574:31How to Replace a Pull String on a Push Mower - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow I can replace the starter handle I'll just thread the Rope through the handle. And again tie itMoreNow I can replace the starter handle I'll just thread the Rope through the handle. And again tie it off with a. Knot. Now I can remove the not that we temporarily tied in the rope.
How do you reattach a pull cord?
1:583:54How to Replace the Pull Cord on a Small Engine by @Gettin' Junk DoneYouTubeStart of suggested clipEnd of suggested clipBut I've already replaced it you're gonna take this and spin it by hand against the spring. You keepMoreBut I've already replaced it you're gonna take this and spin it by hand against the spring. You keep spinning it over and over. Until you get to the point where you have a lot of tension.
How do you fix a pull cord that won't go back in?
0:412:58HOW-TO Tighten A Limp Starter Rope That Won't Retract On A Small EngineYouTubeStart of suggested clipEnd of suggested clipI'm just going to turn counterclockwise. One turn on this one if the rope was out further I would goMoreI'm just going to turn counterclockwise. One turn on this one if the rope was out further I would go two turns counterclockwise. And with this recoil here one turn counterclockwise fix.
How much does it cost to replace a pull cord on a lawn mower?
Replacing a ripcord on your lawn mower is a quick and relatively straightforward job most homeowners can tackle. It takes less than an hour and you probably won't spend more than $20 on parts if you have the basic tools you need to do the job.
How do you start a lawnmower without a cord?
0:001:02How to start a mower without a pull start - YouTubeYouTubeStart of suggested clipEnd of suggested clipAround. This circular piece in and the flywheel is and just keep wrapping it. Make sure to keep itMoreAround. This circular piece in and the flywheel is and just keep wrapping it. Make sure to keep it tight and then wrap it to where you have enough cord to start pulling.
How do you fix a Briggs and Stratton pull cord?
0:007:31HOW TO Repair The Pull Cord on Your Lawnmower With Briggs ...YouTubeStart of suggested clipEnd of suggested clipBut if the rope wasn't broken and still attached to the recoil. Which you would want to do is loosenMoreBut if the rope wasn't broken and still attached to the recoil. Which you would want to do is loosen this nut here and slide the rope right through the crack.
How do you fix a pull string?
0:004:25HOW TO - Generator Pull Cord Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipToday I'm going to show you to replace the pull cord in your generator. So here's the generator asMoreToday I'm going to show you to replace the pull cord in your generator. So here's the generator as you can see the pull cord is broken that often happens when people have a hard time starting their
What does it mean when the lawn mower string won't pull?
What if the starter rope won't pull? The crankshaft is connected to the blade shaft on your recoil start walk behind lawn mower, so if the pull cord is stuck, it could be because something is blocking the movement of the blade. Disconnect the spark plug for safety, then take a look under the deck.
What is the pull string on a lawn mower called?
Push, or walk-behind, mowers commonly feature a pulling mechanism that is designed to turn the crank shaft and start the lawn mower engine. Also known as a recoil start, the pulling mechanism consists of a few different parts that work together to allow a user to start the mower engine.
How do I replace a frayed lawn mower cord?
You still need to remove the assembly from the mower, although it's possible to do it in place, I don't recommend it. (1) Cut the correct length of new cord, measure it against the old one. Don't remove the old cord yet.
Why is my lawnmower pull cord loose?
Lawnmower pull cord loose? A lawnmower pull cord is likely to become loose when the recoil spring loses its tension. Replacing the spring is the correct fix.
How to stop a pulley from retracting?
2 – Have sharp pliers and a flat screwdriver to hand. Pull the cord out all the way, secure the pulley, use a screwdriver to lock the spokes of the pulley, stops it retracting .
What does it mean when a pull cord doesn't retract?
A broken cord is obvious, a pull cord that doesn't retract is usually a broken recoil spring, and a pull cord that doesn't catch and turn the engine usually means worn pawls.
What causes a pull cord to be heavy?
Too Full – Too much oil or oil that’s too heavy will cause the pull cord to be heavy.
What to do if your pull cord is hard to pull?
If your pull cord is hard to pull (stiff), make sure the bail lever is held during the starting process. I know most of you are in no doubt about how to start your mower, but for anybody that's a little rusty check out "How to start a mower".
How to load up a recoil spring?
If you choose not to remove the pulley, you must load up the recoil spring by turning it anticlockwise three turns. Then lock the pulley with the screwdriver as per the above guide, while you feed in and knot the cord, fit handle and double knot. Remove your locking screwdriver, check operation and refit, your done.
How long does it take to replace a pull cord on a lawn mower?
The mower won’t start so you yank and yank on the pull cord without success. After 15 minutes (and a few expletives 🙂 the pull cord on the mower jambs or breaks. 1.
What to do if playback doesn't begin?
If playback doesn't begin shortly, try restarting your device.
Does the pull cord work on a 5.3?
5.3. 3) The Pull Cord Works Fine – But the Engine Won’t Start
Can you remove a pull cord from a lawn mower?
In that case, you might need to remove the pulley from the assembly. Although most pulleys don’t require removal, it may depend on the quality of your lawnmower.
What happens if you don't use the cord on a lawn mower?
If you don't use enough cord, you'll feel tension too early ; if you use too much, the cord will be slack. Once you're satisfied you have the right length and tension, reattach the engine housing and the cord. Most mowers will have a bracket or small metal loop to hold the cord in place at handle height.
Why does my lawn mower cord snap?
Most cords are cotton or braided nylon, and will eventually snap thanks to the combination of hot weather and sharp, repeated tugs needed to get a mower engine running. When they do, your first step is to access the cord's pulley; ideally, you can also remove and save the plastic "T-shaped" handle attached to the old cord.
How to test pull on a pulley?
Wrap the cord around the pulley several times (without spinning the pulley), then attach the handle and give it a test pull. You should be able to fully extend your arm when pulling before you feel significant tension in the cord and it should recoil quickly into the housing.
What to do if you can't pull a pulley out?
If you can't pull it out by hand, you may need to cut it. If the pulley is filled with dirt or debris, clean it out, since these will cause wear and tear on the new cord
Can you replace a mower cord?
Major work on the engine, for example, is something you don't want to tackle alone, but with a little effort and a fair amount of patience, you can easily replace your mower's cord.
Where is the pull cord on a lawn mower stored?
The mower’s pull cord rope is stored in the pulley, as well as the recoil spring. The pulley will guide and feed the pull cord, in addition to storing it. Pulleys are usually made from plastic and this is a part that can crack.
Where is the recoil on a lawn mower?
The recoil operates the mower’s flywheel. The flywheel sits below the starter, closer to the mower, and near the crankshaft. Magnets sit on the outside of the flywheel and generate magnetic energy as it spins. The magnets will eventually build up enough energy to fire off high-voltage sparks.
What kind of parts do lawn mowers use?
Different lawn mower brands make their components differently. Some will use plastic instead of metal for certain components. Plastic parts will wear out faster, and are less capable of withstanding the stresses of consistent use.
How to check if pawls are broken?
To check if the pawls on your mower are broken, remove the starter and pull the rope to make them pull out. If they don’t pull out, either they’re broken or something else is broken.
Why is my lawn mower not starting?
The pawls are the most likely component to fail and it’s probably why your mower isn’t starting. That said, if the pulley or receiver is damaged, that will also cause issues.
Where is the starter rope on a walk behind mower?
The starter rope is wrapped around a pulley system. That allows it to be pulled out before it recoils into the engine. The pulley sits below the cover at the top of your walk-behind mower, and a spring is in the center of the pulley. As it’s turned, the recoil spring stretches, then snaps back when let go. This immediate snap-back retracts the pull cord and allows you to pull the rope quickly one time after another.
What is the starter rope on a lawn mower?
The starter rope is the only part of the starting system that can be seen. But inside your mower, the rope activates a series of parts that start the engine.
What happens when you pull a lawn mower cord?
You know when you pull the cord, it rotates a hub that connects the crankshaft and spins the blades. It also connects the mower spark plug, carburetor, and the motor at the same time. These things all together start your lawnmower. But due to a stuck pull cord, your lawnmower becomes standstill.
Why is my lawn mower pulling cord stuck?
When dirt and debris block the lawnmower blade area, the pull cord becomes stuck. Tilt the lawnmower into its sideways to check the blade area. And clean it if you identify any blockage.
How to choose a pool cord for a lawnmower?
Try to choose a pool cord that doubles the length of the distance between the lawnmower motor housing and the handle.
How to clean rust off bearings?
Clean the rust of the bearing by using steel wool. The steel wool must be fine grade. Otherwise, it will damage the bearing. Properly clean the pocket of the bearing and the shaft as well.
Do you need to recoil the starter cord on a lawn mower?
Before reassembling the bearing, you need to recoil the starter cord in the mower starter spring.
