- Remove the recoil housing cap Unscrew the cap that holds the pulley to the recoil starter housing. ...
- Untie the rope Untie the knot in the rope and slide it out of the housing.
- Replace parts (if needed) Swap out the pulley, housing or spring if the parts need replacing.
- Re-tension the spring Now it's time to re-tension the spring. Think about how you want the rope to return into the housing. ...
- Attach the cap Reattach the cap that holds the pulley to the recoil housing. ...
- Reinstall the rope Line up the holes on the pulley and the recoil housing and thread the rope through them both. ...
- Coil the cord
How to rebuild a recoil starter?
Tools Required:
- Safety Glasses
- Flat Head screwdriver
- Phillips head screwdriver
- Shop towels or rags
- Lighters
How do you recoil the coil in the pull start?
- Use a putty knife to separate one coil from the rest of the spring.
- Ignite the Bernzomatic TS8000, and slowing apply heat to the single coil, heat until the coil is cherry red.
- Using the pliers, bend the coil to match the other end of the spring.
How to fix Stihl pull start recoil?
How to Replace the Starter Rope & Rewind Spring on a Stihl Blower
- Remove the spark plug wire with a pair of needle-nose pliers.
- Cut the old starter rope just below the rubber, T-shaped pull handle. Fish the end of the old rope out of the back of the rubber piece.
- Remove the side cover of your Stihl blower with a screwdriver. ...
- Pry out the old recoil starter assembly with your screwdriver.
How to repair a small engine recoil starter?
How to Rewind the String on a Recoil Starter
- Remove the recoil assembly from the engine by unscrewing the screws or bolts that hold it in place.
- Turn the recoil assembly over, and remove the pulley by unscrewing the bolt that's securing the pulley to the assembly.
- Untie the knot at the end of the string. ...
- Reinstall the pulley onto the recoil assembly. ...
How do you fix a pull start recoil?
0:352:51How-To: Fix a Broken Recoil Rope - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe've applied a double knot on the other end of the rope. We've done the same thing we drew the ropeMoreWe've applied a double knot on the other end of the rope. We've done the same thing we drew the rope through the handle. And apply - double knot at the end.
How do you fix a pull start that won't retract?
0:352:58HOW-TO Tighten A Limp Starter Rope That Won't Retract On A Small EngineYouTubeStart of suggested clipEnd of suggested clipI'm just going to turn counterclockwise. One turn on this one if the rope was out further I would goMoreI'm just going to turn counterclockwise. One turn on this one if the rope was out further I would go two turns counterclockwise. And with this recoil here one turn counterclockwise fix.
How do you fix a recoil spring starter?
0:050:56How to Rewind a Recoil Starter Spring--A Quick Fix - YouTubeYouTubeStart of suggested clipEnd of suggested clipIn first I just align the tab on the spring with the notch and the housing. And then I just wind theMoreIn first I just align the tab on the spring with the notch and the housing. And then I just wind the spring back into the housing. And that's how simple it is to rewind a starter spring.
How do you fix a recoil starter on a lawn mower?
0:171:19Replacing the Recoil Starter on a Lawn Mower - YouTubeYouTubeStart of suggested clipEnd of suggested clipPosition the new recoil starter in the blower housing and snap it into the retainer clips snap theMorePosition the new recoil starter in the blower housing and snap it into the retainer clips snap the recoil starter guard into place position the blower housing on top of the engine.
What causes a pull cord to lock up?
One way the starter cord can get stuck is due to hydraulic lock, which is caused by oil getting trapped in the combustion chamber. You'll need to release the compression and the oil, so remove the spark plug and then give the cord a tug.
How do you lubricate pull start?
3:535:41How To Lubricate A Sticky Starter On A Chain Saw or Weed EaterYouTubeStart of suggested clipEnd of suggested clipRight I usually go on the top when I put a couple good blasts in the in the top in the hole that'sMoreRight I usually go on the top when I put a couple good blasts in the in the top in the hole that's closest to the top blast. It in there like that.
How does a recoil starter work?
Recoil start When the rope's grip is pulled, the rope uncoils, tensions the spring, engages the clutch and turns the crankshaft, spinning it to crank or start the engine before the end of the pull stroke. The running of the engine then disengages the clutch.
How do you replace a pull string?
2:033:54How to Replace the Pull Cord on a Small Engine by @Gettin' Junk DoneYouTubeStart of suggested clipEnd of suggested clipBut I've already replaced it you're gonna take this and spin it by hand against the spring. You keepMoreBut I've already replaced it you're gonna take this and spin it by hand against the spring. You keep spinning it over and over. Until you get to the point where you have a lot of tension.
How do you fix the pull string on a lawn mower?
2:574:31How to Replace a Pull String on a Push Mower - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow I can replace the starter handle I'll just thread the Rope through the handle. And again tie itMoreNow I can replace the starter handle I'll just thread the Rope through the handle. And again tie it off with a. Knot. Now I can remove the not that we temporarily tied in the rope.
How do you rewind a recoil spring on a lawn mower?
0:196:52Easily Fix Your Pull Start Recoil Spring for Small Engine - YouTubeYouTubeStart of suggested clipEnd of suggested clipHey everybody broody here from take a bath productions with another video showing you how to fixMoreHey everybody broody here from take a bath productions with another video showing you how to fix various things today we're going to be working with this starter spring that goes to a chainsaw. This
How do you fix a pull start on a Briggs and Stratton engine?
0:007:06Pull Starter Repair On Briggs & Stratton Engines - Snowblowers Etc.YouTubeStart of suggested clipEnd of suggested clipSo you may have to drill up the rivets to get the recoil off or take the whole shroud off to repairMoreSo you may have to drill up the rivets to get the recoil off or take the whole shroud off to repair this but fortunately for today all I need is a nut driver to remove the recoil.
How do you fix the pull cord on a leaf blower?
1:483:24How To Fix a Broken Leaf Blower Cord - YouTubeYouTubeStart of suggested clipEnd of suggested clipRun your new cord through the handle. Pull the bad cord out of this plastic piece push in the newMoreRun your new cord through the handle. Pull the bad cord out of this plastic piece push in the new cord tie a small tight knot in it. Pull the cord back down pull it into the handle.
How do you fix a Briggs and Stratton pull start?
0:007:31HOW TO Repair The Pull Cord on Your Lawnmower With Briggs ...YouTubeStart of suggested clipEnd of suggested clipNow once the three bolts are off just simply remove the cover. Now this recoiled the rope is broken.MoreNow once the three bolts are off just simply remove the cover. Now this recoiled the rope is broken. So all I have to do is to pull the rope out of the eyelet over here.
How do you fix the pull cord on a trimmer?
2:114:41How to Replace the Pull Cord of a Weed Trimmer - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo once we get that here we just tie a temporary knot just so we don't lose the strain into. It. SoMoreSo once we get that here we just tie a temporary knot just so we don't lose the strain into. It. So the next thing to do is to pull the string fully out and then check to see.
Why does my lawn mower string not pull?
0:102:38Lawn Mower Won't Start: Can't Pull the Recoil Starter Rope - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou might have a problem with the recoil starter or the engine might be locked up we'll remove theMoreYou might have a problem with the recoil starter or the engine might be locked up we'll remove the blower housing to check the recoil starter on.
How long does it take to fix a recoil starter?
Luckily, when this happens, you can fix your recoil starter in about 20 minutes. Your recoil starter may also fail because the pulley or recoil housing has worn and the spring no longer sits in the housing correctly. We used a Briggs and Stratton starter for this repair, but most starters will require the same steps.
How to replace a spring on a recoil starter?
1. Remove the recoil housing cap. Unscrew the cap that holds the pulley to the recoil starter housing. If your spring has slid out of the slots in the housing, then you can continue with the repair. If the housing, pulley or spring have failed, then you will need the proper replacement parts before continuing. 2.
How to keep a pulley from spinning?
With the pulley in the recoil housing, turn it about six times. Once you have tensioned the spring, use a small screwdriver to keep the pulley from spinning. 5. Attach the cap. Reattach the cap that holds the pulley to the recoil housing.
How to thread a rope through a pulley?
Line up the holes on the pulley and the recoil housing and thread the rope through them both.
How to fix a broken starter?
Coil the cord. Hold the recoil starter firmly--it is still under tension--and remove the screwdriver. Pull the starter cord tight and then let go of the pulley. Control the rope speed as the pulley winds the rope back into the starter. Conclusion You can easily repair a broken small engine recoil starter yourself.
Why does my lawn mower's recoil starter fail?
In most cases, the recoil starter fails because the spring slides out of place, causing it to lose tension. Luckily, when this happens, you can fix your recoil starter in about 20 minutes. Your recoil starter may also fail ...
How to keep a knot from untying?
If you're worried about the knot untying itself, add a coating of thin super glue to keep it secure. Pull the starter cord tight in the housing and ensure the knot won't interfere with the pulley's ability to rotate in the housing. 7. Coil the cord.
