Repairing Guides

how to repair roof drip edge

by Prof. Victor Kiehn Published 3 years ago Updated 2 years ago
image

How to Fix a Roof Drip Edge

  • Installing roof drip edge flashing properly. Install roof drip edge along the eaves, add underlayment, then place drip...
  • Place the metal roof drip edge flashing along the gable ends. Once all the underlayment is applied, go back and place...
  • Save yourself some aggravation.

Replacing Drip Edge Eave Strips:
Lift up roof shingles, and nail the eave strip in place with galvanized roofing nails. Overlap the other pieces of eave strip by at least 1” and nail them in place. Cut the last piece on the lower eave flush with the roof decking on the other end.

Full Answer

How to install a drip edge on an existing roof?

The steps below will then follow:

  • Find the nails holding the old drip edge and remove them out with a pry bar or hammer.
  • Jerk old drip edge pieces.
  • First, fix the new drip edges on the attics.
  • Slip drip edges underneath the felt underlayment and shingles. ...
  • Drip edges should spread beyond the roof decking by 3/4 of an inch.
  • Use a roofing nail to nail them in place.

More items...

How to install drip edge the proper way?

Materials Required

  • Drip edge
  • Ice and water shield
  • Roofing felt
  • Roofing nails
  • Staples

How to protect your roof with drip edges and underlayment?

This includes:

  • Keeps rain from blowing into the wood decking, which will cause rotting over time.
  • Sends water that is running off the roof away from the fascia board and away from the building.
  • Prevents insects and other pests from penetrating the edges of the roof.
  • Keep gaps from forming at the bottom of the roof.

More items...

Does your roof have drip edge on it?

It is safe to keep in mind that not all roofs have drip edges. However, a drip edge may be added before or after a shingle is placed. So, if you’ve relocated into a property without one, it isn’t too late to add one to preserve and extend the life of the roofing.

image

Do I need to replace my drip edge when replacing roof?

If your roof doesn't have drip edge, water gets behind your gutters and rots out both your fascia board and roof decking. When getting a roof replacement, your drip edge must be replaced. Be aware, some roofing contractors leave it off your estimate to lower their prices to beat out the competition.

How do you seal a drip edge roof?

0:215:04How to Install Drip Edge and Step Flashing | This Old House - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd they gently put it against the fascia. Board and then they nail it then they take their shinglesMoreAnd they gently put it against the fascia. Board and then they nail it then they take their shingles. And they put them on top and they make it flush with the edge.

How much does it cost to fix drip edge?

Drip edge – Replacing drip edge flashing costs $1 to $2 per linear foot and prevents water from going underneath the shingles at the roof's edge and rotting the fascia, soffit, or roof decking....Roof flashing repair cost.TypeAverage costRoof vent pipe$200 – $500Roof valley$200 – $850Drip edges$325 – $1,2002 more rows

Can you glue down drip edge?

Secure the drip edge with roofing cement. Apply a continuous bead of cement along the top of the drip edge, then press down on the shingle. If necessary, secure the ends of the drip edge with short roofing nails; just be sure they're positioned high up under the shingles.

Can you replace drip edge without removing shingles?

The drip edge is often replaced when new shingles are installed, but it can be replaced at any time. Asphalt roof shingles can become brittle in cold weather, so wait until a warm (but not hot) day to remove and replace eave stripping.

Should drip edge be caulked?

Drip caps must be installed properly to be effective. Don't caulk the seam where the siding meets the drip cap. If water gets behind the siding, this seam opening allows drainage. It's important that a drip cap slopes down and out away from the house.

How do you attach drip edge?

2:576:49How To Install Drip Edge On A Roof - YouTubeYouTubeStart of suggested clipEnd of suggested clipOver this drip edge right to the corner. And as you can see it sticks out a little bit. So what you'MoreOver this drip edge right to the corner. And as you can see it sticks out a little bit. So what you're going to want to do is you're going to want to cut this end back and tuck it around the corner.

How do you replace fascia without removing drip edge?

0:2216:07How to Replace Fascia and Soffit without removing DRIP EDGE!YouTubeStart of suggested clipEnd of suggested clipPull this fascia out and then we'll get that little piece out of there. So then i can just take myMorePull this fascia out and then we'll get that little piece out of there. So then i can just take my next piece slip it back up there make sure you stick around at the end of the video.

Where is drip edge installed on roof?

The correct placement of a roof drip edge is on top of the roof's exterior cover directly between the sheathing and the fascia board, which forms a drainage gap between the drip edge and the fascia board. As a result, the drainage improves water flow and protects the roof from potential water damage.

Does tar paper go under drip edge?

0:018:22Roofing - Does Drip Edge go Under or Over Underlayment or Tarpaper at ...YouTubeStart of suggested clipEnd of suggested clipWell apparently Florida seems to be the only state that allows the drip edge to go over or under theMoreWell apparently Florida seems to be the only state that allows the drip edge to go over or under the underlayment at the eave.

Do you nail drip edge?

Nail the drip edge to the roof deck with minimum 12-gage roofing nails spaced 8 to 10-inches on center and 1-½ to 3-inches from the edge of the sheathing. Adjacent drip edge pieces should be lapped minimum 2 inches. Asphalt shingles should overhang the exterior edge of the drip edge by ¼ to ¾-inch.

Should shingles hang over drip edge?

Shingles should be installed over the drip edge a minimum of 3/8” (9 mm) at both the eave edge and the rake edge. If the drip edge extends… out from the rakes and eaves (typically called DL Style or D Type), the shingles may be installed flush with the drip edge.

Where to put drip edge on roof?

The key is to have your lowest layer of drip edge on the bottom, your underlayment above that, and the sloped drip edge on top. This allows water to drip off with minimal risk of accruing damage.

What is drip edge flashing?

A drip edge flashing, or a gutter apron, is a piece of metal that runs alongside the roof of your home to protect your fascia and soffits from water damage. The metal lip runs underneath the first layer of shingles and directs water away from the building, ensuring the water runs off instead of creeping back and causing a leak.

What is the best rake for a roof?

Curve-bladed and wheeled rakes are the best at protecting your roof.

What is a gutter apron?

F - Type F, or more commonly known as the gutter apron, is a type that lends itself well to repairs and replacement of existing lining. It has an extended leading edge and a greater angle, leading water directly into a gutter system, and ensuring all water is carried away.

How to choose a snow rake?

When choosing the right rake, it is vital to consider the height of your roof in relation to the length of its handle. Snow removal rakes are extendable, so you should look at the maximum extension length of the handle.

When attaching a new section of drip edge, just leave an inch or so of spare flashing over the first?

When it comes time to attach a new section of drip edge, just leave an inch or so of spare flashing over the first piece to not leave any areas uncovered.

Where does flashing meet the edge of a roof?

There is another method that is more involved depending on if the corner is along your gable (the sloped, triangular portion of your roof) or if you have a piece too short to wrap around. In this, you make two markings: one where your flashing meets the edge of the roof, and the other just an inch from that point.

Introduction

The correct installation sequence for drip edge, roofing felt and ice and water shield can be confusing, since it changes from eaves to gable ends. Here's how to keep it straight.

Installing roof drip edge flashing properly

Install roof drip edge along the eaves, add underlayment, then place drip edge along the gable end. The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge.

Place the metal roof drip edge flashing along the gable ends

Once all the underlayment is applied, go back and place the roof drip edge flashing along the gable ends of the roof. Covering the ends of the ice-and-water barrier or felt paper with drip edge ensures that windblown rain that gets under the shingles will run over the underlayment, not on the sheathing.

Save yourself some aggravation

But save yourself some aggravation and get the corners cut on the gable and eave pieces so they mate properly before installing them. That's the only way you'll get clean locking corners.

What is drip edge on a roof?

A properly installed roof includes drip edge along both the eaves and the gable ends. On eaves, it is placed under the underlayment. On gable ends, it is installed over the underlayment.

What is drip edge flashing?

Metal drip edge flashing is an important element of any roofing edge. It bends around the edge of the roof, channeling any moisture that penetrates the shingles away from the roof decking. A properly installed roof includes drip edge along both the eaves and the gable ends. On eaves, it is placed under the underlayment. On gable ends, it is installed over the underlayment.

What are the signs of rot on a roof?

By Matt Brown. The eaves at the bottom of a roof and the gable ends that run up the slope are often the first to show signs of rot and damage. Their position at the edge of the roof leaves them susceptible to moisture infiltration, ice dams and wind, which can uplift the bottom course of shingles. If, however, the rest of your roof is in good ...

How to replace a damaged piece of plywood?

Any damaged plywood should be replaced. Cut out the damaged section with a circular saw. Measure the dimensions of the piece you cut out and cut a piece of the same size from a new piece of plywood. Nail the new piece into place.

How far should ice be from a roof?

Local building codes call for an ice barrier to cover either the bottom 3 feet or 6 feet of the roof. Replace any damaged or missing ice barrier on your roof, overlapping new pieces over the old. After the ice barrier is installed, the roof surface should be covered with a felt underlayment.

Can you reuse shingles?

You may be able to reuse some of the shingles you removed, but if they are damaged, purchase new shingles the same color and style. Lift the upper courses of shingles again and slide the new shingles underneath. Nail them into place. Apply a bead of roofing adhesive over the new nail holes.

Where to put eaves on a roof?

Install the eave strips on the lower roof edges first, with the eave strips under the shingles and felt underlayment.

How to cover gap between gable eaves?

Cut and bend the end of the gable eave strip to cover the gap between it and the lower eave strip.

What is the strip of metal flashing that runs under the roof along the eaves of your house called?

The strip of metal flashing that runs under the roof along the eaves of your house is called eave strip or drip edge. Eave strips help support the roofing that extends past the roof decking and keeps rainwater from running down the fascia board.

What is eaves stripping made of?

Now, many homes will have eave stripping made from galvanized metal, which is designed to keep it from rusting. But without proper maintenance, it can become very unsightly with all the rust spots that can form.

Can you replace drip edge on asphalt roof?

The drip edge is often replaced when new shingles are installed, but it can be replaced at any time. Asphalt roof shingles can become brittle in cold weather, so wait until a warm (but not hot) day to remove and replace eave stripping.

Can you paint aluminum shingles?

Now, one alternative is to replace it with this type of metal, which is a vinyl coated aluminum which won’t rust. And it won’ t need any type of painting, just a little bit of cleaning from time to time. Now, generally it’s replaced at the same time your shingles are replaced, but really it’s fairly easy to replace it anytime.

Can you paint drip edge shingles?

A better alternative is vinyl coated aluminum eave strip, which won’t rust and don’t need to be painted. The drip edge is often replaced when new shingles are installed, but it can be replaced at any time.

What happens if you put a ladder on a roof?

If it's cooler/cold outside, the ladder leaning on the edge will break off the overhanging shingles, eventually allowing water penetration.

How does water get under shingles?

But some of it also gets sucked under the shingle by capillary action (and is assisted by wind). On a house with such a low pitch, it doesn't have far to travel to get behind the flashing and get onto bare wood. (as a side note, this is why in my area, it seems most appropriate to first lay tar paper and THEN install any flashings on TOP of the tar paper... the idea being that if water gets over the top of the flashing for any reason, at least there is tar paper there to protect the majority of the sheathing. If you do it the other way around, and water gets over the top of the flashing, it is on 3" of bare wood.)

How many inches should I lap a gutter apron?

Where one gutter apron overlaps another, I like to lap it a minimum of 6"... again, because of capillary action.

How wide is a gutter apron?

The top edge of the gutter apron is a little wider- about 3 1/2" wide, and all of it rests on the sheathing, which means it will lay FLAT when it is nailed. The front edge of the flashing is longer and is bent at an angle because, unlike d-style drip edge, it is designed to be installed on a pitch.

Why are there notches in the first row of shingles?

This allowed water to get behind the fascia board. Also, the shingles in the first row do not have any "overhang" to get the water away from the structure.

How big is the slit in a shingle?

That picture may be misleading. The slit in the shingle doesnt actually go all the way up, its just a 1/8" or so.

Can you stick gutters behind flashing?

and having the back of the gutter hit the bottom of your plywood edge once you shove it 1/2" up behind, gutter apron gives you a full 2 1/2" to stick the gutter behind, meaning you can actually give the gutter some slope and it will still stay tucked behind the flashing.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9