how to repair satellite dish cable

by Mariane Waelchi Published 3 years ago Updated 2 years ago

So to fix satellite signal, start by loosening the nuts that attach the dish and support pole together. Next, reorient the dish; the easiest way to do this is to ask someone to watch the TV and direct you to the best angle for good signal.

Full Answer

How do you fix a satellite dish that is not working?

How to fix a broken satellite TV signal?

However, there is no need to panic because this has an easy fix. So to fix satellite signal, start by loosening the nuts that attach the dish and support pole together. Next, reorient the dish; the easiest way to do this is to ask someone to watch the TV and direct you to the best angle for good signal.

How do I connect a satellite dish to a TV?

Select a satellite you wish to connect to. Pick a satellite that is in range of your particular dish. There are numerous satellites out there, but dishes cannot get signals from all of them. If you bought your dish from a TV service, for instance, you might have a hard time connecting to their competitor's satellites.

Do I need a professional installer to set up a satellite dish?

This article has been viewed 63,784 times. Learn more... Rather if you have Dish, AT&T, or cable and you are planning on getting satellite service for your home, you don't need to call a professional installer. Even if you don't have much construction experience, you can set up a satellite dish.

How do you fix a cut dish cable?

0:533:38How To Fix A Cut Coaxial Cable-F Connector Repair Tutorial - YouTubeYouTubeStart of suggested clipEnd of suggested clipTool right over here just like that we're actually going to feed the cable. In and it just seatsMoreTool right over here just like that we're actually going to feed the cable. In and it just seats perfectly right there and we're going to crimp it down you're going to see that blue line disappear.

How do I fix my satellite cable?

3:144:16How To Fix Cut Repair Make End On Coax Coaxial TV Cable WireYouTubeStart of suggested clipEnd of suggested clipSo basically it's all you do is you put the cable in like that. And it comes you make it flush toMoreSo basically it's all you do is you put the cable in like that. And it comes you make it flush to the ends. And you gently kind of push on it and twist the cable.

How do you splice satellite cable?

0:001:33TV & Electronics : How to Splice Coaxial Cables - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure the dielectric. Comes to the seats at the bottom of the F. Plug. Both. And theseMoreMake sure the dielectric. Comes to the seats at the bottom of the F. Plug. Both. And these compression cables need to be crimped. That's what this tool does that crimps them down tight.

How do you fix a broken coaxial cable?

How to Repair a Coaxial CablePaint on liquid electrical tape if the insulation covering is damaged but the line is intact. ... Cut the damaged area of the wire out if the coaxial cable has been cut into. ... Twist the new ends onto each wire end that you just cut back. ... Join the two ends together with the coax joiner.More items...

Can a cut coax cable be repaired?

The outside of the coax cable consists of a synthetic insulating jacket. With all of the layers that compose a coax cable, simply splicing two ends of a cut cable could have disastrous effects. But by fitting the severed ends of your coax cable with new connectors, you can rejoin the cable using a coax coupler.

How do I know if satellite cable is working?

1:333:32How To Test Coaxial Cable With a Multimeter - TheSmokinApeYouTubeStart of suggested clipEnd of suggested clipSo want to do that I'm going to put one probe on the pin. And one probe low and then a shield on theMoreSo want to do that I'm going to put one probe on the pin. And one probe low and then a shield on the outside connector. And you can see on the multimeter it says o L.

How do you connect two pieces of coaxial cable?

0:492:31ANTSIG : How to join a coax TV cable - YouTubeYouTubeStart of suggested clipEnd of suggested clipInto one side of the capsule. Ensure the copper reaches halfway into the capsule secure the copperMoreInto one side of the capsule. Ensure the copper reaches halfway into the capsule secure the copper in place by re tightening the screws repeat this on the other side with the new coax cable.

Can you solder coaxial cable together?

Yes you can. Use self-annealing tape to insulate the inner and make sure the screen braid is spread evenly before spot soldering.

Can you join coaxial cable without connectors?

If you have a coax cable without a connector, installing your own is a simple task. Strip the wire and expose its inner conductor. Then push a connector over it and crimp it in place. For tight spaces, use a right-angle connector to avoid bending the cable too much.

How do you replace a coaxial cable?

0:155:33How to Install a Coax Cable F Connector with Common ToolsYouTubeStart of suggested clipEnd of suggested clipHere I cut off the end of the coax cable. So I'm gonna show you how to put a new one on because thisMoreHere I cut off the end of the coax cable. So I'm gonna show you how to put a new one on because this cable isn't gonna be moved a lot I'm just gonna use a twist on F connector.

How do I fix my sky twin cable?

0:158:27Repair Sky Aerial Cable - YouTubeYouTubeStart of suggested clipEnd of suggested clipOr a satellite connector the way work is normally the cable goes in this end and this end hereMoreOr a satellite connector the way work is normally the cable goes in this end and this end here screws onto the Sky box onto your Freesat box.

How do I connect my TV to aerial cable?

You'll also need an aerial lead and a working aerial.Plug your aerial lead into the aerial socket on your box (1). ... Using an HDMI cable, connect to the equivalent socket on your TV to the port marked HDMI 1 on the box. ... Put your TV on standby, then switch the TV on using your TV remote control.More items...

Can you splice Sky cable?

That's why you need coaxial cable, not just two wires side-by-side like regular mains power cable. This also means that you can't reliably splice coaxial cable without very careful consideration of the joint geometry.

Step 1: Tools

Left to right: wire cutter, cable trimmer,something to kneel on. Make sure the cable trimmer has an RG-6 setting. You can buy the cable trimmer at Home Depot or any hardware store that stocks cable parts and supplies.

Step 2: Supplies

Left to right: 2 F-F RG-6 compatible cable adapters, 2 twist on RG-6 F connectors, 1 6' length of RG-6 cable (with F connectors already attached). In case F and F-adapter terminology is confusing, it means this: An F connector has internal threads (and a wire poking out from the center) to connect to another cable section. But what if you have 2 F connectors and you want to connect them together? Then you use an F-adapter, which has external threads on both sides to attach to the F connectors..

Step 3: Make a Clean Cut on the Cable

This just makes it easier to attach the twist on F-connector. From here on out, the steps should be applied to both cable ends.

Step 4: Strip the Cable

Not shown: Using the wire cutters, carefully cut away the entire covering of the cable, to expose the little wire right in the middle. Make this cut about 1/4 inch from the end. Then strip the cable using the RG-6 setting on your cable stripper.

Step 5: Attach Twist on Connectors

Slide them over the cable ends and twist them clockwise to tighten. The inner wire should poke through the end of the connector about 1/8 inch after you are done.

Step 7: Attach the 6' Cable to Each F-adapter

Job done! Now go inside and play some games on the internet! Oh, and don't forget to call the cable company so they can do a permanent fix.

How to fix satellite signal?

What spray to use on satellite dish?

In this case, use WD-40® Specialist Fast Release Penetrant Spray, which will quickly penetrate and free the bolts.

Why does my satellite antenna lose its orientation?

One of the biggest problems your satellite antenna may face is heavy winds, this can often blow the dish causing it to lose its correct orientation. This can mean that it can no longer provide the decoder with any signal. However, there is no need to panic because this has an easy fix.

Why does my antenna get water?

You may find that sometimes heavy rain or melting snow can draw water into the antenna’s connectors. Since you won’t have the special instruments to check if these connections are the source of the problem, you should check the connectors to check if it is the cause. Start by loosening and removing the connectors.

What to do if your cable is oxidized?

If they appear oxidized, they will need to be replaced with new ones of identical size and diameter. The end of the cables must be peeled and prepared correctly (making sure the central conductor doesn’t touch the outer layer!) and then you can put the connectors back.

Can satellite dish antennas be preserved?

Satellite dishes or digital terrestrial antennas are not elements that require continuous preservation. However, you may find your signal will suffer after long periods of time without proper satellited maintenance. In extreme cases, the antenna can become completely obscured after strong winds, heavy rain and snow. Satellite dish maintenance may seem daunting especially if you have never done it before. However, it is definitely worth doing to fix your satellite signal when needed!

Why is my Dish Playmaker Not Working?

There may be three reasons why your Playmaker is not working. The first is that the Playmaker is designed to work with the Dish system only. If you have a different set up this may be your main problem .

Why is My Dish Playmaker Making Grinding Noise?

According to Dish itself, the grinding noise does not come from broken gears. Instead, it comes when the voltage is too low. The dish or the equipment just does not have enough power to move the satellite into the proper position.

Is Dish Playmaker Waterproof?

It is probably more water-resistant than waterproof. According to the warnings in the manual , you cannot place the dish in water deeper than one inch. If you ignore that rule, you could damage the electronics inside the dish.

How to set up a satellite dish?

1. Select a flat spot on or around your home. Find a level place that is accessible if you need to clean off or adjust the satellite dish later. If you have space, the safest place for a satellite dish is on the ground. It will have plenty of room to point north or south, depending on where you live.

How to connect a satellite dish to a wall mount?

Connect the adjustment panel on the dish to the wall mount. Fit the dish onto the open end of the support. If everything is attached correctly, it will fit inside or behind the adjustment panel. You can then add the 1 or 2 remaining bolts to fasten these pieces together. If the dish looks good, then you're ready to position it to communicate with a satellite.

How to install a LNB?

First, slide the handle of the LNB onto the open end of the arm. Secure it with nuts and bolts, then take the LNB out of the box. It looks almost like a round speaker or flashlight. Position it on the handle, facing it toward the dish before bolting it in place.

How to adjust a dish with a LNB rod?

Fit the U-shaped rod inside the adjustment panel. Your dish will have a bent metal rod that fits into one of the slots on the adjustment panel. Slip the rod inside, sliding its prongs through the holes. Ensure the prongs point toward you rather than the tail end of the LNB rod you connected earlier. Fit a small clamp over it, followed by a washer and nut on each prong.

How to connect a satellite dish to a low noise block?

Attach the antenna bracket to the low noise block (LNB) arm. Your dish will most likely come with a flat metal plate to connect the satellite dish to the L-shaped LNB arm and other components. Position the plate, so the prongs are on the left and right, facing you. Hold the LNB arm between the prongs with the tail end extending out past the plate's opposite side. Place some 3⁄4 in (1.9 cm) lag bolts through the arm and into the plate, tightening them clockwise with a wrench.

How to mount a dish to a wall?

Find the bolts that came with your dish, usually 1⁄2 in (1.3 cm) lag bolts. Fasten the bolts by using a cordless screwdriver. Make sure the mount feels secure in the wall before you move on.

How to set up a dish?

One of the best ways to set up a dish is by anchoring a metal pole in the ground with concrete, then mounting the dish on top of it. The rod gives the dish more height without it needing to be on the roof.

What to do if satellite dish is damaged by high winds?

If high winds cause problems then the dish may not be securely fixed. Call a satellite engineer to get the dish secured. Check your cables – make sure that the feed is securely connected and that the cable from the dish to the back of your satellite receiver is undamaged.

What causes interference in a satellite dish?

Blocked signal – the dish needs a clear line of sight to the satellite. Scaffolding, buildings, walls and even trees blocking the path to the satellite may cause interference.

What to do if your set top box doesn't work?

Set-top box – if you are using a set top box try resetting it. If that doesn’t work then there may be a problem with your equipment or your viewing card. Contact your satellite television supplier for help.

Can satellite dish be fixed?

If high winds cause problems then then dish may not be securely fixed. Call a satellite engineer to get the dish secured.