How to Fix a Seam on a Vinyl Bounce
- Step 1. Prepare a cupful of water mixed with 1/2 tsp. of dishwashing liquid. Inflate the faulty bounce. Brush soapy...
- Step 2. Cut an oblong transparent vinyl patch big enough to overlap the seam by an inch on all sides. Trim off a...
- Step 3. Clean the surface of the repair with a wad of cotton-wool soaked in rubbing alcohol. Blow the...
How to repair a tear in a bounce house?
If you’re repairing a tear on the bounce house, you will now follow the steps above for applying a bounce house patch using a Bounce House Patch Kit (link to Amazon). Sewing a tear with the awl kit and then applying a patch is the most permanent professional bounce house patch repair that you can do.
How do you apply a bounce house patch?
Some larger bounce houses have zippers that can open up and give you access to the inside of the bounce house. This is the best place to apply the patch because the pressure when inflated will be pushing the patch more into place, rather than the air pressure pushing the patch outwards.
How do you fix a leaking inflatable bounce?
Fix a leak in an inflatable bounce with a vinyl repair kit. Inflatable bounces, such as bounce houses, are a source of entertainment for children ranging from toddlers to teens. Unfortunately, with boisterous play, the seams sometimes spring a leak, and this causes the device to slowly collapse.
How do you fix a leaky bounce on a vinyl siding?
Brush soapy water onto the suspect areas with a 1/2-inch paintbrush and watch for bubbles. Measure the length of the leak with a ruler and mark the area with an erasable grease pencil before deflating the bounce. Cut an oblong transparent vinyl patch big enough to overlap the seam by an inch on all sides.
How do you fix a hole in a seam of inflatable bounce house?
To patch a bounce house, you will need to cut a round patch from a patch kit and apply to the damaged area with vinyl cement or patch glue. If possible, patch the tear from the inside of the bounce house. If the tear is along a seam, or damage to the stitching, you will need to re-stitch with a sewing awl.
What kind of glue do you use to patch a bounce house?
vinyl cementSimply apply the vinyl cement to the cleaned area on the unit and also on the secondary vinyl (patch or what you are gluing to the inflatable). The vinyl cement needs to dry for a couple of minutes to become tacky then apply together with pressure for a few minutes.
How do you sew a jumping house?
1:515:20How To Stitch And Patch A Cut On An Inflatable Bounce House - YouTubeYouTubeStart of suggested clipEnd of suggested clipWith the knot underneath. You're going to go across from the hole you started on once you get itMoreWith the knot underneath. You're going to go across from the hole you started on once you get it underneath you're going to zigzag you can go diagonally to the other side. And come back up like that.
Can You Use Flex Seal on a bounce house?
0:021:532018.10.14 - Using flex-seal tape to fix bouncy houses - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe just apply that right in there and it sticks all the time keeps all that air from coming out andMoreWe just apply that right in there and it sticks all the time keeps all that air from coming out and it's got a nice clean.
How do you seal seams on bounce castle?
0:381:51How to patch a leaking seam with repair tape - Bounce House TutorialYouTubeStart of suggested clipEnd of suggested clipJust make sure that the edge of your tape is anchored and secure to the vinyl. Before you startMoreJust make sure that the edge of your tape is anchored and secure to the vinyl. Before you start peeling off the rest of it. So I'm going to keep the rest of the seam stretched out and firm.
Can you use epoxy on inflatables?
3:304:16How To: Inflatable Repair Adhesives Guide - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou'll want to use G flex epoxy G flex is a very strong and flexible epoxy that will stick to justMoreYou'll want to use G flex epoxy G flex is a very strong and flexible epoxy that will stick to just about anything as long as the surfaces are prepared properly.
How do you fix a ripped inflatable?
To begin your quick inflatable repair, deflate your item completely. Then, clean the small hole or tear with isopropyl alcohol. Step 2: Patch the leak. Patching a small leak or tear on your inflatable is simple with a quick-curing UV repair adhesive that bonds directly to the material.
How do you fix a tear in a Little Tikes bounce house?
0:039:04Little Tikes bounce house patching. - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo we'll see to fix it I got this tear aid type-a from Amazon it wasn't that expensive it was aboutMoreSo we'll see to fix it I got this tear aid type-a from Amazon it wasn't that expensive it was about 20. But it will bugs i. Total came out to probably like around 30.
Can you sew an inflatable?
Stitching or special repair patches fix damaged inflatables. The downside to inflatables is that they are prone to leaks, punctures or tears that render them unusable. Rather than discarding your favorite holiday inflatables, many of them can be patched with tape or a vinyl repair kit.
Does Flex tape work on inflatables?
3:139:53Fixing a hole in a inflatable paddle board with FLEX TAPE - YouTubeYouTubeStart of suggested clipEnd of suggested clipLet's get about flex tape is that since since this is a inflatable paddle board it kind of it flexesMoreLet's get about flex tape is that since since this is a inflatable paddle board it kind of it flexes with that as it deflates. So you can see there's kind of some wrinkles.
How do you patch an inflatable vinyl?
Patch It Up!Step 1: Drain The Water. ... Step 2: Cut The Patch. ... Step 3: Dry And Clean The Patch Area. ... Step 4: Inflate The Kiddie Pool. ... Step 5: Apply The Glue. ... Step 6: Apply Your Patch. ... Step 7: Let It Dry.
Can you use flex seal on an inflatable pool?
3:4616:03Flex Seal: Does It Work?? Sealing our Intex Easy set Pool!! (2020)YouTubeStart of suggested clipEnd of suggested clipI know you can use flex seal while there's actually you know water coming out.MoreI know you can use flex seal while there's actually you know water coming out.
How do you patch a hole in a bounce house?
If you happen to catch the damage while the bounce house is in the field, you can use TPU tape to make a quick and easy repair. Simply clean the affected area with alcohol, apply the tape to the damaged spot, and then use a seam roller to smooth it out.
Can you patch a bounce house with Gorilla tape?
It is not recommended to use Gorilla Tape or Duck Tape to repair a bounce house. Even if it is waterproof, these types of tape do not have much flexibility or elasticity to them so they will rub off and not last.
How do you repair a nylon bounce house?
Vinyl bounce houses are fixed with vinyl glue, while nylon bounce houses are fixed using a sewing kit. Because nylon is basically fabric, you can treat it as such and stitch a nylon bounce house just as you would a torn jacket.
What glue is good for vinyl?
Polyurethane glue is ideal for gluing thinner flexible vinyl together as well as gluing vinyl to other surfaces like wood or plastic.
How do I prevent rips and tears in my Bounce House?
Choose an appropriate site that is free of sticks and rocks - Store your bounce house properly - Set rules for children, including a no shoe policy.
How much does it cost to repair a Bounce House?
Vinyl Repair Kits, Sewing Awls, and other tools you may need will ultimately determine the total cost. For a rough estimate, let’s call it $10-30....
How do I repair any netting on the Bounce House?
You could sew the netting back together with the right equipment (needle, string, etc).
How to fix a bounce?
of dishwashing liquid. Inflate the faulty bounce. Brush soapy water onto the suspect areas with a 1/2-inch paintbrush and watch for bubbles. Measure the length of the leak with a ruler and mark the area with an erasable grease pencil before deflating the bounce.
How to repair a patch on a vinyl wall?
Spread a liberal amount of vinyl repair adhesive onto the patch area with the brush provided in the kit. Position the bottom of the patch an inch below the seam. Hold the rest of the patch away from the adhesive with one hand and carefully smooth it flat with the palm of your other hand to remove any creases and air bubbles. Work as fast as you can because vinyl adhesive dries quickly.
Why is my inflatable not fully inflated?
Waiting to fix even a small torn seam puts your customers at risk. A torn seam on the bottom of your jumper or other inflatable could be causing air to leak out, so that your inflatable will not stay fully inflated.
What happens if you put sand on a water slide?
If a water slide or other moonwalk has grit or sand, the sand will function just like sandpaper and slowly break away at the stitching of your inflatable and cause seam tears. The last thing you want to do to try and solve this issue is to tape it with duct tape or gorilla tape.
Can you fix a torn inflatable?
At Fix My Bounce House, we can repair torn seams on any inflatable made by any manufacturer. Some repair companies only service one particular manufacturer, but we will repair any moonwalk. We have repaired torn seams on everything from giant slides to Velcro walls. Torn seams on inflatables can be dangerous. The safety of your customers is very important to us. Even a small torn seam can become larger very quickly with the internal pressure from the blower and the external pressure of kids jumping. Waiting to fix even a small torn seam puts your customers at risk. A torn seam on the bottom of your jumper or other inflatable could be causing air to leak out, so that your inflatable will not stay fully inflated.
What to use to make bubbles last longer?
If all else fails, you’re going to want to turn to soap and water. Some folks recommend mixing in some glycerin, which is useful for retaining the effectiveness of the bubbles you’re about to create - using a detergent helps to lower water’s surface tension, which in turn enables bubbles to last longer.
How to get a patch to not stick?
First, make sure the patch is flat and not stuck to another piece of itself. After that, you have two choices . One, sit there and hold the pieces together for several minutes. Or two, find a heavy object and get it to do the job of maintaining an adequate amount of pressure on the patch site. Your choice.
What does it mean when a part is sticking up?
Any part that is sticking up is a part that will not properly bond. Add more glue if need be, or, get a heavier object to press down upon the patched leak.
Can you use corn syrup in a bounce house?
You will want to properly clean your b ounce house if you’re going to add in a third party adjunct (ie - the glycerin, corn syrup, or other substitute).
How to Find the Hole in Your Bounce House
It’s not always an easy task to find smaller holes in the house. For your first attempt at finding one, run the blower so you can walk the perimeter and feel for any air escaping.
Step-by-Step Guide to Patch a Hole in Your Bounce House
Fix your bounce house properly by using a proper vinyl patch kit. It does take a little time to accomplish your task. However, the bit that takes the longest amount of time is finding the leak. Since you already found it using the above tips, you’re already about halfway to completing the job and getting back to sitting in the shade.
Quick Patch Options
If you’re short on time, then you can use one of two quick patch options:
Is the Tear at the Seam?
If you discover that stitching has become damaged or the tear causing the leak is on a seam, then you can consider sewing the seam. A quality sewing awl kit gives you everything you need to sew the seam.
When to Call in a Professional
If you’ve followed the step-by-step instructions, made your repairs, and the problem persists, then it’s a good idea to call an inflatable repair expert.
When to Replace Your Bounce House
If the air leak still persists after you’ve tried the patch kit and called in a professional, it may be time to invest in a new bounce house.
How to Prevent Vinyl Tears in the First Place
Now that you know how to patch and repair your bounce house, you might want to know how to prevent rips and tears in the first place.
How to fix a leaky inflatable?
Step 1. Find out exactly where the leak is. Fill a spray bottle with a mixture of soap and water and spray it liberally on the inflatable item along the seams . You'll notice that the solution starts to bubble up where the leak is located, so take note of the position of the hole.
How long to wait to fill inflatable sandbox?
Fill the inflatable about halfway with air and wait another 30 minutes or so to make sure that the goop has dried completely.
How long does it take for plumber's goop to dry?
Apply plumber's goop liberally to the seam and let it dry for about 15 minutes. If possible, apply some goop to the inside of the seam as well, so that it spreads out and gives an extra layer of protection when the inflatable pressurizes.
Do inflatables come with patch kits?
Most inflatables come with a patch kit that works in most instances. If you have a hole on the seam of your inflatable, however, you may find that little patch just isn't up for the challenge. In this case, you have to get creative.
