How to Repair Cedar Shake Siding
- Step 1 - Inspect the Siding. Scrutinize the siding and look for shakes that have come slack from the nails or ones that...
- Step 2 - Color Difference. Note the color dissimilarity between the new and the old shingles. The old shingles will have...
- Step 3 - Remove the Damaged Cedar. Force open the damaged cedar shake by inserting a blade...
How to install staggered cedar shake siding?
Things You Will Need
- Building paper
- Staple gun with 3/8-inch staples
- Utility knife
- 5d galvanized box nails
- Shingle hatchet or hammer
- Measuring tape
- Scaffold
Should you install soffit before siding?
- Dramatic improvement in home appearance: Within installing of home siding can improve your home appearance. ...
- New siding increases your property value: Installing a new siding at your home can also increase your home value when you sell it. ...
- Energy efficiency improvement: You can also get the benefit of low energy
How much does vinyl shake siding cost?
“For a professional to install 1500 ft. of vinyl cedar shake siding, homeowners will pay between $6,750 and $11,250. Prices typically decrease per square foot as the project size increases, as well as with less complicated projects.” Expect to spend $300 to $425 per square for the materials only.
How to install exterior lights on siding?
Tools Required
- 4-in-1 screwdriver
- Cordless drill
- Wire stripper/cutter
Why is cedar shake siding so popular?
Why are old shingles faded?
About this website
How do you restore cedar shakes?
Simply mix the powder with water in a large spray container per the directions on the bottle and spray it onto the house. Wait 15 – 20 minutes and use a handled brush to scrub the cedar shingle siding gently, as you don't want to crack or break them. Then you'll want to hose down the shakes to wash everything off.
How much does it cost to replace shake siding?
The average cost to install cedar shake siding ranges from $6.50 to $13.50 per square foot. You can expect to pay between $16,600 and $25,500 for a contractor to install new cedar shake siding on a typical house. This includes the cost of having a contractor remove the existing siding.
How do you repair vinyl shake siding?
0:312:55How to Replace Damaged Vinyl and Polymer Shakes Siding Cedar ...YouTubeStart of suggested clipEnd of suggested clipNext pry the nails out of the nail hem of the damaged panel push up on the panel to unlock it andMoreNext pry the nails out of the nail hem of the damaged panel push up on the panel to unlock it and pull it down to remove. It. Be sure to tape or replace cut or torn house wrap.
How do you repair wood shake shingles?
1:523:59How To: Replace a cedar shake shingle - YouTubeYouTubeStart of suggested clipEnd of suggested clipLine it up with your old. Ones. We're going to take our nails you want to get the nail where theMoreLine it up with your old. Ones. We're going to take our nails you want to get the nail where the next shingle is going to cover it. So we're going to go about an inch. Up. All it requires two nails.
How long does shake siding last?
20-40 yearsIf well-maintained, cedar shake siding endures the elements well and can last many years. Some manufacturers offer warranties of over 25 years because cedar shake siding can last 20-40 years when well-maintained. However, your cedar shake siding should stay off of the ground to extend its longevity.
Does vinyl shake siding look cheap?
Although the vinyl shakes cost makes them an appealing option when compared to traditional wood shakes, they are not necessarily the best option on the market. They still require a fair amount of maintenance, can suffer damage, and if not installed properly, can look cheap and degrade very quickly.
How do you fix vinyl siding without replacing it?
2:256:20How to Replace Damaged Vinyl Siding | Ask This Old HouseYouTubeStart of suggested clipEnd of suggested clipActually cuts away the nailing strip on the top about two inches and they also remove a section ofMoreActually cuts away the nailing strip on the top about two inches and they also remove a section of the snap-in. Piece on the bottom.
Can you replace a single piece of vinyl siding?
Vinyl siding is tough but not indestructible. If a falling branch or a well-hit baseball cracked a piece of your siding, don't fret — you can make it as good as new in about 15 minutes with a zip tool and a replacement piece. It's as simple as unzipping the damaged piece and snapping in a new one.
Can you fill holes in vinyl siding?
If they're small enough, filling the holes with a matching caulk can be a quick and inexpensive fix. If you can't find caulk that matches your vinyl siding, you can use white caulk and purchase matching paint to conceal the hole.
How do you fix a wood shake?
To repair a wooden shake roof:Step 1: Use hammer and sharp chisel to split damaged shake. Slant chisel up into shake at same angle as pitch of roof. ... Step 2: Measure gap left by old shake, and cut new one. ... Step 3: Install new shake. ... Step 4: Set heads of nails with nail set, and seal them with caulking compound.
Can you replace just a few shingles?
In the end, if your roof needs just a few shingles replaced or a few minor patches made, you can get a roofer to make those small repairs for you. But, if you need anything more than half of your roof repaired, it's in your best interest to simply re-roof your entire home.
Should I replace my cedar shake siding?
Expect to replace cedar siding every 10 to 15 years. Inspect your cedar siding a couple times each year for the following signs of damage that could require replacement: Loose or damaged panels, which should be nailed down or replaced. Holes, cracks, scratches, or blemishes, which can lead to moisture damage.
Is Shaker siding more expensive?
Wood siding isn't as popular as it once was, but cedar shake and shingles display the beauty of wood in a prominent way. It tends to be more expensive than other wood siding options, due mostly to labor, and has some advantages over other wood siding options.
Should I replace my cedar shake siding?
Expect to replace cedar siding every 10 to 15 years. Inspect your cedar siding a couple times each year for the following signs of damage that could require replacement: Loose or damaged panels, which should be nailed down or replaced. Holes, cracks, scratches, or blemishes, which can lead to moisture damage.
How much does it cost to replace shingle siding?
Cedar Shingle Siding Cost Guide & Installation Prices. The average cost to install cedar shingle siding ranges from $6 to $15 per square foot. You can expect to pay between $10,200 and $24,600 for a licensed contractor to install new cedar shingle siding on a typical house.
How much does it cost to install vinyl shake siding?
Vinyl Siding Installation Cost If you hire a professional to install your vinyl siding, you will pay about $3.70 per square foot in labor costs. Labor costs range from $2 to $5 per square foot. Costs vary based on where you live as well as the time of year you're installing your siding.
Why is cedar shake siding so popular?
Cedar shake siding is appealing to many people due to the fact that it provides a rural effect in a natural way. It is resistant to insects and is relatively strong against moisture.
Why are old shingles faded?
Note the color dissimilarity between the new and the old shingles. The old shingles will have faded a bit due to the effect of the weather conditions. A good tip to use to avoid this color difference is to have some spare shingles stored outdoors. They will be exposed to the weather's effects and ultimately they will generate a color similar to the shingles which had been installed originally.
Step 2 - Color Difference
- Note the color dissimilarity between the new and the old shingles. The old shingles will have faded a bit due to the effect of the weather conditions. A good tip to use to avoid this color difference is to have some spare shingles stored outdoors. They will be exposed to the weather'…
Step 3 - Remove The Damaged Cedar
- Force open the damaged cedar shake by inserting a blade beneath the bottom edge of the shingle. Normally a cedar shake will have 2 nails fastening it. Normally, one can shift the shingle back and forth using a blade or a wide metallic instrument, while pulling it away from the boxing.
Step 4 - Sample The Old Cedar
- Make use of your old cedar shake to serve as a guide. Place it over a new cedar shake that is a bit wider, and then use a straight edge so as to illustrate a line along the edge of the new shingle.
Step 5 - Slice The Cedar
- Cut along the line sketched, with a sharp utility knife, and do the same thing in the same spot on the backside so as to slice the cedar.
Step 7 - Final Touches
- Then, carefully nail in the new shake. Locate the shingle and use 2 nails to fix the shingle in place. Make sure to use nails which are galvanized, and of a suitable length. The nails should show on top of the upper shingle.