
Step-by-Step How to Repair a Roof Edge
- Finding the Damage. To locate rotted areas of the roof’s edge, gently lift up shingles with a pry bar or taping knife.
- Replacing Decking. Any damaged plywood should be replaced. Cut out the damaged section with a circular saw. Measure the...
- Drip Edge. Metal drip edge flashing is an important element of any roofing edge. It bends...
Full Answer
How to reroof over existing shingles?
What You Need
- Power nailer or roofing hatchet
- Tape measure
- Roofing shovel or flat pry bar
- Hammer
- Drill
- Carpenter's square
- Tin snips
- Utility knife
- Chalkline
- Broom
Do it yourself roofing shingles?
Step 1: Removing the Old Roofing Shingle. Remove the old roof’s shingles and repair any damages sections of the roof covering. Use a roofing shovel to do so. This square-ended shovel with teeth can pull out nails. Step 2: Take Measurements. Measure the length and width of the roof surface and calculate the footage that needs to be covered.
How to replace or repair a damaged shingle by roofingintelligence.com?
To fix broken shingles: Gather up your pry bar, hammer, utility knife, replacement shingles, and some 1-1/4-inch roofing nails. Climb on to the roof. Slide pry bar beneath the row of shingles directly above damaged section.
Can you put new shingles on top of Old Ones?
To level out an existing asphalt-shingle roof, rip down (reduce the height of) two courses of shingles, as shown in the drawing below. Because asphalt shingles are routinely exposed 5 in., rip down the first strip (the starter course) so that it is 5 in. high. Then lay it over the original (old) first course so that the strip is flush against ...

How do you replace shingles on a roof edge?
1:277:39How to Replace or Repair a Damaged Shingle by RoofingIntelligence.comYouTubeStart of suggested clipEnd of suggested clipSo make sure to separate it all the way around. You can just slide the flat bar in like this andMoreSo make sure to separate it all the way around. You can just slide the flat bar in like this and slowly pry the shingle loose. Once you've broken the glue bond.
How do you fix the edge of a roof?
0:352:13Roof Edge Repair with Flashing - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd direct that any so the corner tile covers this and this would overlap the edge flashing andMoreAnd direct that any so the corner tile covers this and this would overlap the edge flashing and force everything down and to the next flashing. And then out.
How do you fix a leaking roof edge?
0:126:573 ways to fix leaking roof and gutters - DIY - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo this one here is probably the most commonly used one very easy to use simple straightforward outMoreSo this one here is probably the most commonly used one very easy to use simple straightforward out of a caulking gun you can squeeze that material. Out smooth off the area.
How do you repair damaged shingles?
If a shingle is simply cracked or torn, you don't have to replace it—just repair it. Start by applying a thick bead of roofing sealant under the crack. Press the shingle down and apply a second bead of sealant on top of the crack. Then spread the sealant with a putty knife.
Can you replace drip edge without removing shingles?
The drip edge is often replaced when new shingles are installed, but it can be replaced at any time. Asphalt roof shingles can become brittle in cold weather, so wait until a warm (but not hot) day to remove and replace eave stripping.
What's the edge of a roof called?
Eaves. The lower edge of a roof (usually overhanging beyond the edge of the house).
Is Flex Seal good for roof leaks?
Flex seal for rooftops is the ideal product to manage roof leaks. The sealant can be placed on the roof when it is leaking or has a leaking problem. Flex seal comes in a liquid form, making it easier to apply and works superbly. It protects the roof from rust stains, UV rays, and mildew growth.
What is roofing drip edge?
Drip edge is a metal flashing that is installed at the edges of the roof to help control the flow of water away from the fascia and to protect the underlying roofing components. Drip edge overhangs the sides of the roof and has a small metal flange that is bent away from the fascia.
How do you install drip edge on an existing roof?
1:563:26How To Properly Install Drip Edge on your Roof -Jonny DIY - YouTubeYouTubeStart of suggested clipEnd of suggested clipBefore you mount it about a half inch. So you want about a half inch between the drip edge and theMoreBefore you mount it about a half inch. So you want about a half inch between the drip edge and the fascia a gap. So that the water just doesn't run off the edge onto your fascia.
Will roof leak with one shingle missing?
Will your roof leak with just one missing shingle? Maybe. Just because you lose a shingle or two doesn't mean water will immediately drip from your ceiling. However, such a missing shingle could cause issues over time if the surrounding shingles deteriorate from exposure to water, wind and sunlight.
Can you replace just a few shingles?
In the end, if your roof needs just a few shingles replaced or a few minor patches made, you can get a roofer to make those small repairs for you. But, if you need anything more than half of your roof repaired, it's in your best interest to simply re-roof your entire home.
Will a roof leak if shingles blown off?
This is problematic as the nails holding your shingles in place have loosened and your roof is now more vulnerable during the next wind or rainstorm. No longer sealed and water-resistant, your shingles may allow water to pool (or ice dams to build) and leak through your roof.
What is a roofing verge?
The 'verge' usually refers to the outer ends of your roof above the gable end commonly an apex. Traditionally, these areas at the edge of your roof are fixed with a sand/cement mortar mix in order to prevent water ingress and unwanted guest such as birds or bees/wasps nesting in your roof.
How do you install roof edge flashing?
0:215:04How to Install Drip Edge and Step Flashing | This Old House - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd they gently put it against the fascia. Board and then they nail it then they take their shinglesMoreAnd they gently put it against the fascia. Board and then they nail it then they take their shingles. And they put them on top and they make it flush with the edge.
How much does it cost to replace drip edge?
The cost of drip edge Drip edge is always going to be included in your roof replacement. Because of this, it's going to have an impact on the price you'll pay for your new roof. The standard drip edge used (aluminum) is going to be around $2.00 a linear foot, including labor to install.
What is a rake edge on a roof?
Defining the Rake of a Roof Specifically, it's the exposed part of a gabled roof that extends from an eave to the ridge of the roof's sloped sides. It covers the top edge of a roof and is typically cut from a variety of roofing materials. Concrete or PVC, cedar, pine, and smartboard are all common candidates.
What is drip edge on a roof?
A properly installed roof includes drip edge along both the eaves and the gable ends. On eaves, it is placed under the underlayment. On gable ends, it is installed over the underlayment.
What are the signs of rot on a roof?
By Matt Brown. The eaves at the bottom of a roof and the gable ends that run up the slope are often the first to show signs of rot and damage. Their position at the edge of the roof leaves them susceptible to moisture infiltration, ice dams and wind, which can uplift the bottom course of shingles. If, however, the rest of your roof is in good ...
What is drip edge flashing?
Metal drip edge flashing is an important element of any roofing edge. It bends around the edge of the roof, channeling any moisture that penetrates the shingles away from the roof decking. A properly installed roof includes drip edge along both the eaves and the gable ends. On eaves, it is placed under the underlayment. On gable ends, it is installed over the underlayment.
How to replace a damaged piece of plywood?
Any damaged plywood should be replaced. Cut out the damaged section with a circular saw. Measure the dimensions of the piece you cut out and cut a piece of the same size from a new piece of plywood. Nail the new piece into place.
How far should ice be from a roof?
Local building codes call for an ice barrier to cover either the bottom 3 feet or 6 feet of the roof. Replace any damaged or missing ice barrier on your roof, overlapping new pieces over the old. After the ice barrier is installed, the roof surface should be covered with a felt underlayment.
Can you reuse shingles?
You may be able to reuse some of the shingles you removed, but if they are damaged, purchase new shingles the same color and style. Lift the upper courses of shingles again and slide the new shingles underneath. Nail them into place. Apply a bead of roofing adhesive over the new nail holes.
How to fix shingles that dont hang over the edge of house?
I had my roof replace about 5 years ago. Over 75 percent of the shingles hang over the edge about 1 inch and that keeps the fascia board clean. But on the back side, the middle portion of it the shingles meet up with the edge. This lets run off from the roof run down the fascia board and dirt and dedris from the tree accumulate on it. It is also causing rot.I seems the back side of the house is not completely even.
What is drip edge on shingles?
Often times shingles are cut flush with the edge of the roof and a metal drip edge is installed to direct runoff from the roof away from the fascia (and into gutters if they are installed).
What angle should drip edge come off?
bend the end of the drip edge further away from the fascia board. It should come off at ~45 deg angle.
Why is my roof flush?
Well, the part that is flush collects dirt from the roof and the wood is rotting since the water is running down it. Where as the other parts of the roof are not dirty and they are dry since the water runs off the shingles and falls to the ground......
Can you drip metal edge?
Respectfully, you have no drip metal edge. The water runs off the shingles and down the trim and facia.
How far off should shingles be on a damaged roof?
The end seams should be lined-up about a foot off to one side of the damaged one. In other words, you'll want to make sure that you pull off shingles in a radius around the damaged portion, to make sure you get everything.
What is ridge cap shingles?
The ridge cap shingles are just regular 3 tab shingles that are cut and turned sideways. They are nailed down so that the nails are not exposed. Take a stack of regular 3 tab shingles and cut little v notches at the top edge of the shingles between the tabs. This also keeps the ridge shingles from being completely square and the corners tuck in nicely.
How long do shingles last?
It depends. Most shingles have a 15-25 year lifetime guarantee, so it depends on the age and condition of the shingles if they can be used again.
How to get up on a roof?
Any time you're getting up on the roof you need to practice roof safety. Wear protective eyewear, heavy-duty gloves, and gripping boots appropriate for walking on the roof. Preferably, you'll also install roof jacks to have something to stand on, and harnesses to protect yourself.
Who owns Bumble Roofing?
This article was co-authored by David Bitan. David Bitan is a roofing professional, licensed contractor, and the owner and founder of Bumble Roofing based in Southern California. With over 12 years of construction industry experience, David specializes in restoring, repairing, and maintaining residential, commercial, and industrial roofs. With over 60 years of combined experience, Bumble Roofing provides easy, friendly services to structures including residential, commercial, industrial, multi-family, and government buildings along with hospitals, hotels, and churches. This article has been viewed 323,479 times.
Can shingles cut into a roof?
Damaged shingles can seriously cut into the life of a roof. To keep your house secure, it's important to regularly evaluate and replace damaged shingles to make sure your home is safe and dry. [1] Roofing Contractor & Maintenance Professional Expert Interview. 14 July 2020.
Can you remove shingles in hot weather?
Remove shingles in cool weather. Asphalt and asphalt sealant will heat up in hot weather, making it moldable and much more difficult to remove. It's a lot easier to remove shingles that are cooled down and slightly more brittle than the moldable, so do the work of removing them first thing in the morning, before the sun has beaten down upon them considerably.
Why are there notches in the first row of shingles?
This allowed water to get behind the fascia board. Also, the shingles in the first row do not have any "overhang" to get the water away from the structure.
How does water get under shingles?
But some of it also gets sucked under the shingle by capillary action (and is assisted by wind). On a house with such a low pitch, it doesn't have far to travel to get behind the flashing and get onto bare wood. (as a side note, this is why in my area, it seems most appropriate to first lay tar paper and THEN install any flashings on TOP of the tar paper... the idea being that if water gets over the top of the flashing for any reason, at least there is tar paper there to protect the majority of the sheathing. If you do it the other way around, and water gets over the top of the flashing, it is on 3" of bare wood.)
How many inches should I lap a gutter apron?
Where one gutter apron overlaps another, I like to lap it a minimum of 6"... again, because of capillary action.
How wide is a gutter apron?
The top edge of the gutter apron is a little wider- about 3 1/2" wide, and all of it rests on the sheathing, which means it will lay FLAT when it is nailed. The front edge of the flashing is longer and is bent at an angle because, unlike d-style drip edge, it is designed to be installed on a pitch.
What happens if you put a ladder on a roof?
If it's cooler/cold outside, the ladder leaning on the edge will break off the overhanging shingles, eventually allowing water penetration.
How big is the slit in a shingle?
That picture may be misleading. The slit in the shingle doesnt actually go all the way up, its just a 1/8" or so.
Can you stick gutters behind flashing?
and having the back of the gutter hit the bottom of your plywood edge once you shove it 1/2" up behind, gutter apron gives you a full 2 1/2" to stick the gutter behind, meaning you can actually give the gutter some slope and it will still stay tucked behind the flashing.
