Instructions
- Remove damaged shutter slats.
- Remove the pins from the frame.
- Pop the new pins into the shutter frame.
- Drill bigger holes into slat if necessary.
- Put one side of the slat into a pin.
- Flatten out the other pin using a knife or card.
- Slide the slat down into place.
Full Answer
How to fix loose shutters?
Step 2: Mounting the Shutter
- Check all the holes to make sure the previous anchors broke off. ...
- Orient the shutter correctly and get at least one screw in far enough to hold it up without your help.
- Go to town on the other screws.
How to remove interior shutters?
- Open the shutters completely. Once open, locate the hinges that attach the shutters to the support piece of wood.
- Unscrew the hinges and remove the shutters.
- Unscrew the hinges from the piece of wood that is attached to the wall.
- Remove the support beams from the wall.
- Remove any additional hardware from the wall.
How to replace a shutter lock fastener?
- Put on work gloves and place a ladder next to the window so you can reach the house shutter.
- Insert a hacksaw blade into the space between the back of the shutter and the wall of the building.
- Slide the hacksaw blade downward until it stops on one of the plastic nails.
How to remove shutter plugs?
- Find a long metal screw, and pick a drill bit appropriate for pre-drilling that screw.
- Drill into the remaining shank of the Shutter-lok, all the way to its end.
- Screw the long metal screw into the Shutter-lok.
- Pull the metal screw out. (Ease it out, rocking and twisting if it resists.)
How do you fix a broken shutter pin?
1:222:23How to replace a broken shutter louvre blade or pin - YouTubeYouTubeStart of suggested clipEnd of suggested clipHold the louver blade straight and carefully insert this vehicle. Use the end of the pliers to push.MoreHold the louver blade straight and carefully insert this vehicle. Use the end of the pliers to push. The staple in the loser blade goes through the staple in the control.
How do you fix clip on plantation shutters?
3:568:06How to Fix Plantation Shutters - missing staples and broken magnet ...YouTubeStart of suggested clipEnd of suggested clipYou run it through the metal. Staple that's already existing in the slat. And then you go ahead andMoreYou run it through the metal. Staple that's already existing in the slat. And then you go ahead and get your super glue apply a little bit and then start to force the staple back into its holes.
What size are shutter pins?
1/4 inchThe standard shutter pins will fit inside of a 1/4 inch diameter frame hole with at least 3/8 inches in depth. The pins overall length is 1 inch.
How do you fix plantation shutter slats?
0:281:45How to replace a slat in your push rod shutters - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe slat is dislodged from the panel. Remove this old pin from the panel. Now we're ready to fitMoreThe slat is dislodged from the panel. Remove this old pin from the panel. Now we're ready to fit your new slat. Take your replacement pins. Insert this longer fixed pin like this into the panel.
How do you replace staples in shutters?
0:562:42How to replace a tilt rod staple - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo as far as inserting the new staple goes. Move your louvers to about a 45 degree angle. Reach inMoreSo as far as inserting the new staple goes. Move your louvers to about a 45 degree angle. Reach in from behind typically you'll put a little bit of glue. Super glue gel on the legs of the staple.
How do you fix loose shutters?
2:354:22How to tighten the louvres on your plantation shutters - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's simply a matter of getting a Phillips head screwdriver that will fit in the hole. And turn theMoreIt's simply a matter of getting a Phillips head screwdriver that will fit in the hole. And turn the screw clockwise to tighten or anti clockwise to loosen.
What are shutter pins?
Shutter Tension Pins are utilized when constructing new plantation shutters. These pins eliminate the use of tension screws when constructing shutters. They support the louvers in the shutter panel, and allow the louver to rotate. The narrow end of the nylon pin is inserted into the louver.
How do you install vinyl shutter fasteners?
0:311:24Installing Exterior Shutters using spikes - YouTubeYouTubeStart of suggested clipEnd of suggested clipPut the shutter spike in a hole. Using a hammer gently tap the spike in repeat. Until all sixMorePut the shutter spike in a hole. Using a hammer gently tap the spike in repeat. Until all six shutter spikes are started then finish tapping them all in be careful not to tap them in too far.
Can you replace slats in shutters?
Luckily, shutter slats are held in place with pins that can easily be replaced to reattach any dislodged or damaged slats.
How do you repair wooden shutters?
2:196:00Repairing A Wood Shutter - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd we had to expose them and they had wood plugs protecting. And hiding the screws in order to getMoreAnd we had to expose them and they had wood plugs protecting. And hiding the screws in order to get the wood plug out and expose the screw. I took a 3/16 drill bit and drilled out the plug.
How do you fix manual roller shutters?
A solution to this issue is to spray the components of your roller shutter with a lubricant, such as WD-40. The WD-40 will loosen up the mechanisms, allowing them to move smoothly. Open up the box at the top of your slats and you should be able to investigate further.
How do you reattach window shutters?
Screw a two-inch weatherproof deck screw into each hole to ensure there is still “bite” to the hole. If the screw slips right in, fill the hole with wood filler. Use a Philips head screwdriver to insert the filler into the hole. Let dry 24 hours before continuing.
How do you install a shutter vane connector?
4:045:55How to Repair a Tilt Connector - YouTubeYouTubeStart of suggested clipEnd of suggested clipActually put the tilt connector into the slack. And you wiggle it. Around. Until it goes in and thenMoreActually put the tilt connector into the slack. And you wiggle it. Around. Until it goes in and then. You just repeat.
How do you fix plantation shutters that won't stay open?
0:000:42Ask the Pros: Help! My Shutters Won't Stay Open - YouTubeYouTubeStart of suggested clipEnd of suggested clipTurn on this side and then the other folded back and get at that tighten things up put yourself inMoreTurn on this side and then the other folded back and get at that tighten things up put yourself in position you'll be good to go in no time.
How do you fix manual roller shutters?
A solution to this issue is to spray the components of your roller shutter with a lubricant, such as WD-40. The WD-40 will loosen up the mechanisms, allowing them to move smoothly. Open up the box at the top of your slats and you should be able to investigate further.
Why did CiCi hang out at the front window?
Before the shutters were up, we noticed that CiCi had been hanging out at the front window so that she could watch for our return. After the shutters went up, she didn’t take kindly to the fact that we had covered her window to the world, so she proceeded to knock out four of the slats at the bottom.
Can you replace plantation shutters?
Plantation shutters are pretty expensive, so you want to repair them and not replace them. Here is how to fix broken shutters!
What is missing staple on shutters?
Missing staples allow individual louvers to rotate independent of other louvers. There is a low degree of difficulty to replace shutter staples. Shutter staples are available at shuttermedic.com. Children occasionally grab or tug shutters inappropriately which may break the tilt bar, or tilt rod.
Why do interior shutters not work?
However, on occasion interior shutters are subject to uncommon abuse which results in shutters that do not work properly. The most common failure happens when the shutter staples that connect the tilt bar to the shutter louver are removed ...
Can interior shutters be repaired?
Interior shutters often can not be repaired. View our page on suggested shutter companies to find a retailer.
Can you replace a louver on a plantation shutter?
Shutter louvers can occasionally be damaged inadvertently or by aggressive pets. Plantation shutters can either use a flat or elliptical louvers. It may difficult to match the color of replacement louvers. Paint can be matched by paint suppliers. It may be best to order an extra louver to test stains to match current stain finishes. Order replacement louvers at shuttermedic.com.
What type of pins are used for a louver?
PLANTATION SHUTTER: ONLY nylon pins are used to pivot the louvers. Each nylon pin has a 1/32 in shoulder, allowing even spacing between the louver and style. Nylon pins eliminate the problem of shrinking, swelling and wear with movement associated with using wood dowels on the louvers.
How to reattach a louver that is not open?
If the Rails & Stiles are separating, then reattach them properly. If your louvers will not stay open, first check for the presence of tension screws. Most likely you will find them recessed on the outside of each stile. By turning these screws clockwise, you pull the louver (s) closer to the stile.
What to do if your louvers keep flopping down?
If your louvers keep flopping down, replace the Vinyl Tension Louver Pin (dome head). Insert Tension Louver Pin (part # 1579) on 1 end of louver, and Louver Repair Pin (spring loaded, part # 1570) on the other end of louver.
Do shutter repair kits require special skills?
All our shutter parts, repair kits do not require any special skills. Just a bit of patience, follow the instructions on our our videos and your shutter would be working beautifully again. If you are new at shutter repair, please check out the shutter diagrams to learn the terminologies & locate your parts.
