how to repair sink stopper

1. With a slight twist, try to lift out the stopper. ...
2. Lift the stopper from the drain. Clean off all hair and debris. If the stopper is broken or its seal looks worn, replace it.
3. Face the hole at the bottom of the stopper toward the pivot rod’s location, and drop the stopper back into the drain hole. ...
4. Loosen the set screw on the clevis and adjust the strap up or down so that it operates the pivot rod to open and close the stopper. ...
5. If adjusting the clevis screw doesn’t help, reset the pivot rod by squeezing the spring clip and freeing the pivot rod. ...
6. If water drips from around the pivot ball, tighten the retaining nut that holds the ball in place. ...

How to fix sink stopper that will not stay up?

Steps Download Article

1. Understand a bit of what's going on under your sink. ...
2. Push and pull the rod. Notice whether the drain stopper moves. ...
3. Adjust the nut. On the back of the drainpipe, there is a nut. ...
4. Make sure the two rods are connected. ...
5. Attach the stopper to the lower rod. ...
6. Adjust the location of the lower rod. ...
7. Adjust the travel of the lower rod. ...

How can I remove the stopper from my Sink?

• Wrench or pliers – Depending on how tightly the nut is fastened, you may need a wrench or pliers to loosen it.
• Flashlight – A regular hand-held flashlight may be useful because otherwise, you might not be able to see what you are doing beneath the sink.
• Brush (e.g. ...

More items...

How to put the drain stopper back in the sink?

Part 4 Part 4 of 4: Installing the New Sink Stopper Mechanism

1. Align and place the drain stopper into the sink's drain opening. ...
2. Insert the tapered plastic washer into the horizontal stub on the tailpipe. ...
3. Feed the pivot rod into the stub and through the hole on the drain stopper. ...
4. Feed the pivot nut over the pivot rod and tighten it onto the pipe stub. ...
5. Install and connect the lift handle and extension bar. ...

More items...

How do I fix a bathroom sink stopper?

Method 3 Method 3 of 3: Adjusting a Stopper That Won’t Stay down Download Article

1. Detach the pivot rod from the clevis by removing the spring clip. The clevis is the vertical metal bar that the horizontal pivot rod attaches to beneath the sink.
2. Put the spring clip on the end of the pivot rod. Slide the pivot rod through one of the holes in the metal clip.
3. Align the pivot rod with one of the holes in the clevis. ...

More items...

How do you reconnect a sink stopper?

0:414:58How to repair or reassemble pop-up sink stopper DIY video ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt is completely missing this arm here so all we will have to do is go ahead and plug this new oneMoreIt is completely missing this arm here so all we will have to do is go ahead and plug this new one in and hook it up and it should work like new.

Can you replace just the stopper in a sink?

Lift the sink drain stopper out of the drain. Inspect the rubber seal on the bottom of the stopper head. If the seal is cracked or brittle, the stopper should be replaced. If it's still in good condition, you can reuse it.

Can you replace a pop up sink plug?

Pop up sink plugs can be removed and replaced easily. For more complex installations, use an adjustable wrench or wrench.

How much does it cost to replace a sink stopper?

Replace a Kitchen Sink Drain: national average cost The national average materials cost to replace a kitchen sink drain is $10.61 per drain, with a range between $9.52 to $11.70.

How to tighten a pop up assembly?

Tighten the nut on the pop-up assembly body. This plastic one is made to tighten sufficiently with fingers only and no pliers. Tighten the body nut as tightly as your fingers can tighten it. Be careful that the body of the pop-up assembly does not rotate out of its position. Hold it firmly while tightening.

Can you tighten a pop up nut?

If your pop-up assembly is metal, be careful not to tighten the nut too much with a pair of pliers. Part of the metal nut is a thin washer mounted in the nut and it can push out. Once it does, you will have difficulty making the nut hold the ball on the linkage rod so there are no leaks.

What is a sink stopper?

Sink stoppers are simple but useful tools that prevent water and debris from going down the drain. Although the parts wear out over time, they are fortunately easy to fix even if you have little plumbing experience. The stopper is controlled by a couple of metal bars underneath the sink.

How to fix a stopper that won't stay down?

Start by removing the stopper components. If the stopper won't rise, check and replace the horizontal pivot bar. Alternatively, move the vertical clevis to fix a stopper that won't stay down. Complete the repairs to get a tight-fitting stopper without having to call a plumber. Steps.

What is the retaining nut on a sink?

The retaining nut holds the levers that connect the stopper to its control on top of the sink. It’s not hard to spot since you can see these levers underneath the sink. If the nut looks rusted or leaky, you may need to replace it. Try cleaning or tightening it first before getting a new one.

Where should the pivot rod be in a sink?

Look for the hole at its bottom edge. That hole is where the end of the pivot rod needs to be. Drop the stopper into the sink, turning it so the hole faces the side opening, then push the ball end of the pivot rod into it. The pivot ball should rest right inside the pipe’s opening.

What does it mean when you remove a P trap from a sink?

Removing the P-trap from the sink’s plumbing means you can no longer run water in the sink without causing a big mess. Also, the P-trap usually has water in it, so keep a bucket underneath it.

How to get a retaining nut back on a pivot rod?

Screw the retaining nut back onto the pivot rod. Check the nut to make sure it has a rubber ring called a washer inside of it. Once the washer is in position, slide the nut onto the end of the pivot rod and all the way down to the ball. The nut covers the ball, capping the pipe’s opening.

How to Fix A Bathroom Sink Drain Stopper: 4 Easy Solutions

One of the most common issues – is that the lift rod moves up and down but the stopper doesn’t move. Or something along those lines! Here are four potential solutions that will hopefully fix things up.

4. Does the stopper go up but not down and the stopper is not damaged?

Is your issue that you can push the stopper up – but it never pulls down? A common reason for that is the bottom of the stopper is positioned 90 degrees offset.

The Wrap Up

I hope this helped you out! I know these plumbing projects can be intimidating, but they’re often more accessible than they seem once you get to know the parts a little better.

What Is a Sink Stopper?

A sink stopper is a device that helps firmly close a drainage outlet. When the drainage outlet is closed, the sink can fill with water or other liquids. Though sink stoppers are usually found in the bathroom or kitchen, they can also be used for your basins and bathtubs.

So, How Do Sink Stoppers Work?

To understand how sink stoppers work, you should first get familiar with the different parts of this mechanism and their functions.

A Step-by-Step Guide to Installing a Pop-Up Drain Stopper

Installing a sink stopper is quite simple. Here is what you’ll need for the job:

Learn How to Fix Sink Stoppers DIY-Style

You will need to fix a new sink stopper when you install a new sink or buy a faucet that comes with its own stopper, or when the stopper doesn’t work as it should.