
[Solution] How to Fix Soffit
- Remove Shingle Mold. Pry the narrow shingle mold from the fascia using a flat bar. If it comes off without splitting, reuse it later.
- Remove Rotted Fascia.
- Remove Old Soffit.
- Remove Rotted Rafter.
- Attach Cleat.
Full Answer
How to repair damaged soffit on Your House?
Soffit and Fascia Repair 1. Remove Shingle Mold. Pry the narrow shingle mold from the fascia using a flat bar. If it comes off without splitting, reuse it later. 2. Remove Rotted Fascia. Remove the rotted section of fascia. Be careful not to damage any nearby roof shingles or flashing. 3. Remove Old Soffit. Pull down to remove the old soffit.
Should soffit and fascia be replaced after gutters?
You can even set a reminder in your phone or calendar to check your gutters in the spring and the fall. If you start to notice that your soffits and fascias don’t look quite as beautiful as they did on move-in day, it might be time for a replacement or a repair. Keep an eye out for signs of deterioration:
How much to charge for installing soffit?
To estimate costs for your project:
- Set Project Zip Code Enter the Zip Code for the location where labor is hired and materials purchased.
- Specify Project Size and Options Enter the number of "linear feet" required for the project.
- Re-calculate Click the "Update" button.
How do I repair this soffit flashing thing?
This helps:
- Keep your home’s structure intact. Because gutters prevent rainwater from seeping into your walls and foundation, they help maintain your home’s structural integrity. ...
- Prevent damage to your landscaping. Without gutters to channel it away, rainwater will most likely rush down to the ground, eroding the soil and damaging nearby greenery. ...
- Save money. ...

How do you repair rotten soffit?
The good news is that you won't even need to climb on top of your roof to fix your soffit!Pry off your shingle mold. ... Remove the fascia. ... Remove the soffit's rotting wood. ... Take out the rotted rafter (when applicable). ... Install the new rafter (when applicable). ... Prepare the new soffit. ... Attach the soffit. ... Attach the fascia.More items...•
How do you repair a hole in a soffit?
Patching the Soffit Measure the hole carefully, and cut a patch to fit. The patch should be slightly smaller than the hole, to allow for expansion. Care should be taken to match a tongue and groove patch to the existing soffit. Nail or screw the patch into place.
What can I use to fix soffits?
3:195:19Repair Soffit and Fascia - YouTubeYouTubeStart of suggested clipEnd of suggested clipI'm going to have to cut it. Since this is one solid piece I'm going to take it with the saw and goMoreI'm going to have to cut it. Since this is one solid piece I'm going to take it with the saw and go right to here and we'll be able to pull that little piece out of. It.
Is soffit expensive to replace?
Replacing your soffit generally costs about $20 to $30 a linear foot installed, while replacing your fascia costs about $15 to $25 a linear foot installed. Prices for the project depend on a number of factors, including the materials used and the size of your house.
How do you repair a hole in a vinyl soffit?
1:313:21How to Patch a Hole in Vinyl Siding in 3 Minutes - YouTubeYouTubeStart of suggested clipEnd of suggested clipMaking sure there's no wrinkles. Or bubbles tear aid type B is designed to be used as a permanentMoreMaking sure there's no wrinkles. Or bubbles tear aid type B is designed to be used as a permanent patch on vinyl fabric. But it works on this final siding.
What's the difference between soffit and fascia?
The soffit helps regulate your home's temperature, allowing your roof to “breathe.” Cool, dry air is drawn into the soffit vent, and hot moist air is forced out of roof exhaust vents. The fascia is the attractive board along the side of the overhang and the roof that helps your roof appear finished.
How do you replace one piece of soffit?
Soffit and Fascia RepairRemove Shingle Mold. Pry the narrow shingle mold from the fascia using a flat bar. ... Remove Rotted Fascia. Remove the rotted section of fascia. ... Remove Old Soffit. Pull down to remove the old soffit. ... Remove Rotted Rafter. ... Attach Cleat. ... Attach New Rafter. ... Seal Replacement Soffit. ... Attach Replacement Soffit.More items...
What are rotting soffits ?]?
Unfortunately, rotted soffit is usually caused by leaks that drip down and collect in the gutters and on the soffit boards. It can also be caused by bad weather and pesky animals. Soffits play an important role in your home because they cover the eaves and protect the rafters from weather damage.
Can you put new soffit over old?
If you happen to be working on an older home, most contractors and homeowners find that they will need to install their vinyl soffit over top of old wood. This can definitely be done, but you will need to take several precautions to prevent the wood from rotting beneath this new layer.
What is the best soffit material?
Most roofing and siding professionals recommend that you go with either aluminum or vinyl for your fascia and soffit, as both are more water-resistant, and neither are as prone to rot.
What wood is used for soffits?
Standard soffit material is 3/8- or 1/2-inch-thick exterior plywood in pine (or similar softwoods) or cedar. Common, but much less durable, is Masonite or similar fiberboard soffit, as well as much more weather-resistant fiber-cement.
Why are my soffits dripping?
Gutter Problems A gutter that is clogged with organic debris such as leaves, or that is damaged so that water does not flow down the gutters as intended, can lead to water leaking through the house's soffit.
What is soffit repair?
Soffit repair is a fairly common home improvement project for homeowners. The soffit is the material that is fixed underneath various parts of a building. You can use it to complete installation of cornices, stairs, eaves, cabinets and ceilings. However, soffits have a high vulnerability to damage, especially by weather.
How do I install soffit in a hole?
Fit the new soffit into the hole. Secure it to the rafters with a hammer and nails. Apply acrylic caulk to the seams. It is best to apply just what you need. If you dispense too much caulk, it creates an untidy surface and makes it harder to achieve good results when painted over. Smooth the caulk with a utility knife and allow it to dry completely.
Where to find molding on soffit?
You’re likely to find molding where the soffit lies against the exterior wall. Molding is also used to join the soffit with the fascia. Use a utility knife to remove the molding that runs all along the edge of the soffit.
1. Determine the type and extent of the deterioration
The first and most obvious step is to look for rotten wood. Structural movement of the building may shift the cornice woodwork, opening up joints. This breaks the paint film, letting water soak into the end-grain causing checks, splits, and decay.
2. Plan the repairs
There are four basic types of repair techniques: wood Dutchman (a patch), lap-joint splice, wood-epoxy repair, and complete replacement.
3. Design and lay out the joint
Now that I know the conditions of the board in detail, I can design an effective joint. Here, I’ll use a 3″-long half-lap joint. I lay out the joint with a pencil, combination square and marking gauge (as in Step 2). I mark the shoulder of the lap 3″ back from the end of the board, using the square to make it 90 degrees to the edge of the board.
4. Cut and shape the joint
Next, I cut the shoulder. The depth of this cut extends only halfway through the board. I like to use a Fein multi-tool fitted with a saw blade, which goes a bit slow, but gives me more control for these tricky cuts. Working with a mallet and sharp chisel, I split away the waste [D] and pare down the surface of the cheek until it is nice and flat.
5. Create the replacement part
In the shop, I make the replacement part using the old board end as a pattern. The original soffits are made of heartwood Eastern white pine, so I select a board of the same.
6. Assemble the repair
Back up on the scaffold, I check the part in place, trim it to fit, and drill shank holes in the new part for screws to hold the joint together. Then I glue it into place with an epoxy adhesive.
7. Sand and finish
A light sanding completes the wood lap-joint splice repair, and it’s ready to be painted.

Step 1 – Remove Molding
- You’re likely to find molding where the soffit lies against the exterior wall. Molding is also used to join the soffit with the fascia. Use a utility knife to remove the molding that runs all along the edge of the soffit.
Step 2 – Locate Soffit Seams
- The soffit is usually installed in panels or strips. Trace the seams on each side of the damaged area. Cut through the caulking with a utility knife to separate the individual soffit lengths.
Step 3 – Remove Damaged Soffit
- Use a pry bar to lift out the damaged soffit sections. Watch out for nails lodged in the roof rafters. If you have to cut through the soffit, use a jig saw to cut out a square or rectangular patch. It makes it easier to install the new portion and helps to maintain the stability of the feature. If your soffit is of the tongue and grove type, be sur...
Step 4 – Identify Cause of Damage
- Take some time to inspect the damage. It will help you to determine what may have contributed to the damage. This will enable you to undertake repairs more effectively. The damage could have been caused by some hard impact, small animals, insects or water leakage. Bees and wasps love to nest in the eaves. If you spot any, call an exterminator first to clear them before you work.
Step 5 – Clean
- It is best if you install the new soffit in a clean area. Use a soft scrub brush to clear loose dirt and debris from the area. Wipe clean with a damp cloth.
Step 6 – Take Dimensions and Cut
- Use a tape measure to determine the size of the area to be fitted with new soffit. Cut out a wooden panel to fit the area. Be sure the wood is of the same type as that used on the rest of the soffit installation. It is important that the wood has similar width and durability to create uniformity in the installment.
Step 7 – Install
- Fit the new soffit into the hole. Secure it to the rafters with a hammer and nails. Apply acrylic caulk to the seams. It is best to apply just what you need. If you dispense too much caulk, it creates an untidy surface and makes it harder to achieve good results when painted over. Smooth the caulk with a utility knife and allow it to dry completely.
Step 8 – Finishing
- Apply a suitable primer for wood over the repaired area. You can then paint it with a color that matches the rest of the soffit.