how to repair stripped oil pan threads

by Ima McGlynn Published 2 years ago Updated 2 years ago

^{The Process}

Drain just about every drop of oil from the car. This can take awhile.
Jack the car up in the front, so it tilts away from where the oil pan drain is located. ...
Clean the drain plug opening thoroughly with brake cleaner or acetone and let the car sit in that position until the oil pan drain opening is perfectly dry
Mix the JB Weld. Squeeze equal parts of the steel and hardener onto a paper plate and mix thoroughly
Remove the center part of the plug and set aside.
Apply JB Weld to the threads of the oil pan drain plug, both sides of the attached gasket, and the drain plug opening in the oil pan.
Screw the oil pan drain plug into place. We used an artist's paintbrush to apply the JB Weld to the plug, gasket, and oil pan drain opening and we applied ...

Part of a video titled DIY | STRIPPED ENGINE OIL PAN BEST FIX! - YouTube

0:04

6:20

The most solid way to fix a strip oil pen is to buy the thread tap kit this usually runs anywhereMoreThe most solid way to fix a strip oil pen is to buy the thread tap kit this usually runs anywhere from fifty to a hundred dollars. And it will fix it permanently.

Full Answer

What happens if you have a stripped oil pan drain plug?

A stripped oil pan drain plug can be especially frustrating because it will leave your oil drain plug loose causing a constant leak. If the threads are completely stripped it can even lead to the drain plug not fitting at all which would leave your engine completely empty of oil and unable to be ran.

How do you replace the drain plug on an oil pan?

Many oil drain plug repair kits feature a reaming bit, which removes the remains of any pre-existing threads. This provides a renewed surface, which can be tapped to accept a new drain plug. A specially sized tap will then be carefully threaded into the oil pan’s drain hole.

Do you need a new oil pan drain thread?

Have you ever gone for an oil change and been told the threads on your oil pan drain have been stripped? The very next thing you are told is you need a new one. This is quite an expensive repair and one that you can avoid.

How do I Stop my oil pan from leaking?

These drain plugs can cut new threads in the soft aluminum of your oil pan allowing you to keep your current oil pan installed and drive leak free! Try calling any of our partnering local auto parts stores to see if they carry an oversized drain plug for you vehicle:

Can you Rethread an oil pan?

Lisle Oil Pan Plug Rethread Kit works on soft steel and aluminum oil pans with 1/2 in., 12 mm, and 14 mm threads. The tapping tool ensures the new thread is perpendicular to the gasket surface to prevent any leakages. Kit includes a piloted drill, spring-loaded tapping tool and 5 magnetic drain plugs.

How much does it cost to fix a stripped oil pan bolt?

The general range is between $100 and $350, but there are some vehicles that cost more. You can get an oil pan gasket replacement for between $40 and $150. The part is not the most expensive part of the repair, but the labor can be very intensive.

How do you fix a stripped oil drain?

0:0510:21HOW-TO Repair Stripped Oil Drain Plug Threads - Video - YouTubeYouTubeStart of suggested clipEnd of suggested clipHey guys welcome back to my channel today I'll show you how to rethread a stripped oil drain plugMoreHey guys welcome back to my channel today I'll show you how to rethread a stripped oil drain plug hole on any TV.

How do you helicoil an oil pan?

8:4811:33Stripped Oil Pan Repair Time -Sert / Helicoil Perfection! MUST WATCH ...YouTubeStart of suggested clipEnd of suggested clipHand remember we need loctite on the outside of the insert. And oil on the driver. I'm going toMoreHand remember we need loctite on the outside of the insert. And oil on the driver. I'm going to slowly work that. In. And then with our socket.

What causes stripped oil pan?

Stripping of a drain plug or oil pan's threads generally comes as the result of prior over-tightening. All drain plugs carry a specific torque, to which they should be tightened during reinstallation.

How often does an oil pan need to be replaced?

eight- to nine-yearGenerally, on the average vehicle, oil pans tend to require replacement around the eight- to nine-year mark, unless they've been impacted harder than usual.

Can you use Teflon tape on oil drain plug?

0:205:58Should you use PTFE Tape for your Car Oil Drain Plug ? Let's test.YouTubeStart of suggested clipEnd of suggested clipOf people says that is perfectly fine they have used PTFE tape on their drain plugs all their livesMoreOf people says that is perfectly fine they have used PTFE tape on their drain plugs all their lives and they had never experienced any problems with their engine.

How do you restring a oil pan plug?

2:164:26How to Repair a Stripped Out Aluminum Oil Pan - YouTubeYouTubeStart of suggested clipEnd of suggested clipBack it out a little bit and what clean out some of the shavings. And then put it back in and startMoreBack it out a little bit and what clean out some of the shavings. And then put it back in and start it and do that a couple times until. Until it this goes all the way through the little oil pan.

How much does it cost to replace a oil pan?

between $20 and $1000An oil pan replacement can cost anywhere between $20 and $1000, depending on your vehicle's year, make, and model. Other factors that may affect its price include the pan's brand, capacity, material, and whether or not it comes with a gasket kit.

Which is better helicoil or Time-Sert?

After doing a bit of research it sure seems to me that the Time-Sert is the clear choice for a more full-proof 'permanent" fix. The only advantage to a Helicoil I found, is that it is cheaper. Being in the industry for a little while I have seen time and time again, that cheaper is never better.

Will tightening oil pan bolts Stop leak?

best way to do it is just replace the gasket. Tightening wouldn't do any good, as tightening the bolts any tighter could result in warping the oil pan, or you could over tighten the bolts and it would be hard to try to remove them the next time you had to remove the oil pan.

What is a helicoil thread repair kit?

0:003:42Thread Repair - How to install a Helicoil - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's a little coil of threads. That is installed with a special tool and to do that you need toMoreIt's a little coil of threads. That is installed with a special tool and to do that you need to drill out to the appropriate sized threading hole for this tap comes with this all comes with a kit.

How much does it cost to replace oil drain plug?

How Much Does an Oil Drain Plug Replacement Cost? The cost of an aftermarket oil drain plug can range between $5 and $75. Pricing depends on various factors, such as material, type, color or finish, brand, warranty, and set inclusions. Labor can cost you an extra $70 to $100, depending on the rates in your area.

Does Jiffy Lube replace oil plug?

0:541:47How Jiffy Lube Performs a Signature Service Oil Change ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhile the technician under the hood is performing these checks the technician in the lower bankMoreWhile the technician under the hood is performing these checks the technician in the lower bank underneath your cart begins his work he'll remove the drain plug allowing the older.

How do I Rethread my aluminum oil pan?

Can you replace oil drain plug?

A: If only the drain plug (screw) itself is damaged, replacements are readily available. If the threads of the oil pan are damaged, you need not replace the entire pan — which in some cases can be labor intensive. You don't tell us what kind of car you have, so we will suggest a universal-type oil drain plug.

What causes oil pan bolts to not torque?

The first of these conditions involves damage to the threads of an oil pan’s drain hole. This damage prevents a drain plug (or oil pan bolt) from being properly torqued.

How to remove stripped threads from drain plug?

Drain Plug With Stripped Threads. A drain plug with stripped threads can often be removed simply by rotating it in a counterclockwise fashion, with a wrench or socket. However, it might be necessary to provide a slight amount of outward force on the plug itself, in order to get any remaining threads to engage.

How Does an Oil Drain Plug Get Stripped?

The term “stripped” oil drain plug (or oil pan plug) is typically used to describe one of two conditions. These issues differ from one another in context, as well as possible means of repair.

How to reduce the chance of rounding off a drain plug?

The first of these precautions involves using a properly sized wrench or socket during every oil change. Doing so significantly reduces the chance of rounding off a drain plug’s hexagonal head. Information regarding drain plug size for a particular vehicle can often be found via the Internet, or by consulting a manufacturer-specific service manual.

What is oil drain plug repair?

Oil drain plug repair kits focus on removing any remaining damaged threads within an oil pan’s drain hole, before rethreading this drain hole to accept a slightly oversized plug.

What is a stripped drain plug?

The second condition often described as a “stripped drain plug” actually refers to the rounding-off of a drain plug’s hexagonal head. This prevents a wrench or socket from being properly applied to a drain plug during removal. rounded off head. As a result, one is unable to drain the old oil from an engine’s crankcase.

Why is my drain plug rounded off?

The most common cause of a rounded-off drain plug is the use of an improperly sized wrench or socket during prior removal/installation. This often occurs when a standard socket is used in a metric application or vice versa.

Why is my oil pan drain plug not fitting?

Can aluminum bolts damage threads?

The downfall of aluminum is that it is much easier to damage threads as a similarly sized bolt will hold much less torque in aluminum. The most common places this happens in a motor is valve covers or intake manifolds bolting to aluminum heads or oil pan drain plugs threading into aluminum oil pans. A stripped oil pan drain plug can be especially ...

When to apply anti seize on piggyback center bolt?

Anti-Seize should be applied to the Piggyback Center Bolt after every oil change before it is threaded back into the drain plug

Where to apply JB weld?

Apply JB Weld to the threads of the oil pan drain plug, both sides of the attached gasket, and the drain plug opening in the oil pan.

How to keep a piggyback from rusting?

Apply Anti-Seize to the center part (the Piggyback) and thread it into place. The Anti-Seize will keep the metal from rusting or locking so tightly that it can't be removed for an oil change. When you go for an oil change, make sure they are familiar with the oil drain plug you have inserted.

Does the Dodge Intrepid have an oil pan drain plug?

An auto mechanic friend suggested a Self Threading Oil Pan Drain Plug. We discovered that the Dodge Intrepid does not have a standard oil pan plug size. Even knowing the year, make, and model does not clear that up.

Do you need to remove the piggyback center bolt for an oil change?

They need to know that only the Piggyback Center Bolt is removed for an oil change. If they attempt to remove the whole plug you will, with certainty, need a new oil pan! Anti-Seize should be applied to the Piggyback Center Bolt after every oil change before it is threaded back into the drain plug.

How to keep cuttings out of a hole?

Old mechanic trick to keep the cuttings out of the hole when tapping new threads - coat the tap with grease, particularly the fluted parts . The cuttings stick to the grease. Cut a few threads, back it out, wipe off and regrease -continue the process.

Does Threadsert work?

Threadsert works, but it really is kinda ghetto.

Repairing Guides