
Use the baking soda mixture to clean the battery box and check to make sure the battery box is securely attached to the car. Dry the battery box and the battery cable connectors. In order to replace the battery, place the side post battery securely into the battery box and reinstall the hold down assembly.
How do you fix a stripped battery?
It took a good bite in the stripped-out hole. Let it set for a few days so that it is not gassing from being charged. Then lay it on its side with the terminals facing up. Blow air all around the battery to remove any remaing explosive fumes. Then take a propane torch and melt new lead into the stripped holes.
How do I replace the battery on my Side post battery?
In order to replace the battery, place the side post battery securely into the battery box and reinstall the hold down assembly. Apply the battery grease to the side post terminals to prevent corrosion build-up. Connect the red-colored positive battery cable and tighten the clamp.
How do you clean the negative wire on a battery?
Lift the old battery out of the car and set it on the ground. Create a mixture of one tablespoon Baking Soda to eight ounces water and dip the negative cable connector into the mixture. Use the stiff brush to scrub any debris off the connector.
Should the battery cables be replaced when replacing the battery?
While replacing the battery, it's a good time to inspect the battery cables for wear and tear. Replace these at the same time you replace the battery if necessary.
How do you Rethread a side post battery?
7:5710:00Side Post Battery Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust because this has damaged threads they're a little bit over cut I substitute it by making theMoreJust because this has damaged threads they're a little bit over cut I substitute it by making the threads a little bit larger. So everything will be a nice tight fit in there which. It is now.
How do you replace a side mount battery terminal?
0:112:39How To Replace Battery Side Post Terminal Bolts on GM - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo we're going to want to take the black one off first this one's a side post battery. So we'll justMoreSo we're going to want to take the black one off first this one's a side post battery. So we'll just go ahead and loosen these up i want to disconnect the black one first so then when we're touching.
Can you spray wd40 on battery post?
WD-40 Specialist Fast Drying Contact Cleaner can act as a protective layer, applied on the poles and terminals of the car battery and successfully eliminate oil, deposits of grease and mud.
What thread is a side post battery?
Registered. It's just a 3/8 inch coarse thread.
Do felt washers on battery terminals work?
These washers prevent corrosion on top of the battery and do an excellent job. So far they have been on for over 6 months and the battery terminals look brand new. I would not hesitate to put these on every battery when I change them. No brainer thick felt washers!
Can I replace a side post battery with a top post battery?
Replace the Battery's Terminals Remove the side-post terminals. Replace each battery terminal with a post converter. These parts give you a safe and effective way to convert a side design to a top-post configuration. The converters should stretch between the sides and end up along the topside of the battery.
Is Coke good to clean battery terminals?
You can even get rid of an anthill by liberally dousing the area with Coke. Coke can be used to clean car battery terminals; the slight acidity does not react with battery acid, so you can pour it over the battery and let it wash away corrosion.
Is Vaseline good for battery terminals?
Once the terminals are dry, dab a bit of petroleum jelly onto them. This will lubricate them, help prevent further corrosion, and help strengthen the connection.
What grease can I use on battery terminals?
The grease that should be applied is white lithium grease. It is readily available at automotive stores. It will not interfere with the electrical connection, but will help prevent future corrosion by displacing the air in the surrounding space.
What size thread is a car battery?
The most common battery bolt will have a nut of around 10 millimeters or 0.4 inches, a bolt length of 1.24 inches, and a bolt thread size of 5/16 inches.
What can you put on battery terminals to prevent corrosion?
After removing the terminals, you can apply anti-corrosion washers or a small amount of dielectric grease on your battery's posts. Another great anti-corrosion chemical is the AMSOIL heavy-duty metal protector, which can also be used to prevent rust.
Is WD-40 electrically safe?
It dries quickly, leave no residue and removes over 95% of common surface contaminants, making it the best at cleaning electrical contacts and for optimal performance of equipment. Safe and ideal for use on printed circuit boards, controls, battery terminals, switches, precision instruments and electric panels.
How do I clean battery terminals?
Using around a teaspoon of baking soda, or more as necessary, coat your battery terminals and other affected areas. Pour a small amount of water on each terminal then use your brush to scrub the corrosion away. While a steel wire brush will work the best, an old toothbrush can work with enough elbow grease.
Does WD-40 clean corrosion?
WD-40 can help remove rust from metals like iron, chrome, and stainless steel without further damaging the surface of the metal or removing the paint. The Multi-Use Product is great for loosening and removing excessive surface rust.
How to get a bolt to stay in place when removed?
Take a piece of solder and bend it in an L , insert one leg of the L into the hole and rethread the bolt in , you may have t hammer the solder flat to get the bolt started. The solder will take up the gap and allow the threads to bite. Same idea as a paperclip in a body bolt. Hopefully the solder will stay in place when the bolt is removed.
How to clean up buggered threads?
I've made thread chaser bolts to clean up threads in softer material. Use grade 8 allen bolts and cut the threads with a die grinder in two opposite sides to create a tap like configuration. They will run themselves right in and clean up the buggered threads.
How to make a bolt bigger?
Wrap several layers of aluminum foil on the bolt to make it a little larger or cut a piece of 3/8 threaded rod, clean it well, heat it cherry red and stick it in the hole to melt the lead to it.
How long does it take to fix a larger bolt?
I've done the larger (metric) bolt trick successfully. It's a 5 minute fix if you start the bolt carefully.
Can you run a larger diameter bolt into a battery terminal?
I have always had good luck just running a larger diameter bolt into them. The lead is soft and will conform to the new threads. We get lots of buggered up battery terminal ends/cable ends here at work and this is the cheapest easiest fix.
Can you pour molten lead into a stripped hole?
I've never done this, but you may be able to pour molten lead into the stripped hole and then tap it out to the correct thread size...
Do sparks and batteries mix?
I'm not familiar with drilling out holes, but what I do remember is that sparks and batteries don't mix, so whatever you do, please don't put yourself in a dangerous situation.
Can you make a stud and a nut to tighten the terminal?
Making a stud and a nut to tighten the terminal should work fine as well.
How to remove a bad battery from a side post?
Raise the car hood and locate the bad side post battery. Remove the hold down assembly that holds the battery in place and set it aside for later. Find the proper sized socket or screwdriver and gently unscrew the black-colored negative cable from the negative post. Set this cable aside without letting it touch any metal parts of the car. Repeat this procedure for the red-colored positive cable. Lift the old battery out of the car and set it on the ground.
How to clean a car battery box?
Use the baking soda mixture to clean the battery box and check to make sure the battery box is securely attached to the car. Dry the battery box and the battery cable connectors.
How to clean a negative cable connector?
Create a mixture of one tablespoon Baking Soda to eight ounces water and dip the negative cable connector into the mixture. Use the stiff brush to scrub any debris off the connector. Repeat this procedure for the positive cable connector.
What to wear when working around a car battery?
Put on the latex gloves and safety goggles whenever working around a car battery to prevent any battery acid from contacting your skin or getting into your eyes.
When replacing a battery, is it a good time to inspect the battery cables?
While replacing the battery, it's a good time to inspect the battery cables for wear and tear. Replace these at the same time you replace the battery if necessary.
Do auto parts stores test batteries?
Tips and Warnings. Some auto parts stores will test a suspect battery to determine if it is bad or not. Some batteries come with a warranty that will prorate the price of a new battery over the length of the warranty. Always use care when working around the car battery.
