- Remove the recoil housing cap Unscrew the cap that holds the pulley to the recoil starter housing. ...
- Untie the rope Untie the knot in the rope and slide it out of the housing.
- Replace parts (if needed) Swap out the pulley, housing or spring if the parts need replacing.
- Re-tension the spring Now it's time to re-tension the spring. Think about how you want the rope to return into the housing. ...
- Attach the cap Reattach the cap that holds the pulley to the recoil housing. ...
- Reinstall the rope Line up the holes on the pulley and the recoil housing and thread the rope through them both. ...
- Coil the cord
How do you fix a recoil starter on a small engine?
7. Coil the cord Hold the recoil starter firmly--it is still under tension--and remove the screwdriver. Pull the starter cord tight and then let go of the pulley. Control the rope speed as the pulley winds the rope back into the starter. Conclusion You can easily repair a broken small engine recoil starter yourself.
What causes a recoil starter to go bad on a lawn mower?
As anyone who works with lawn equipment knows, small engine recoil starters eventually fail. When your lawnmower, string trimmer or other tool's pull cord goes slack, starting the engine becomes impossible. In most cases, the recoil starter fails because the spring slides out of place, causing it to lose tension.
How do you fix a broken recoil spring on a rifle?
Remove the recoil housing cap Unscrew the cap that holds the pulley to the recoil starter housing. If your spring has slid out of the slots in the housing, then you can continue with the repair. If the housing, pulley or spring have failed, then you will need the proper replacement parts before continuing.
How do you put the pulley back in the recoil housing?
Think about how you want the rope to return into the housing. You will need to wind the pulley in the opposite direction. With the pulley in the recoil housing, turn it about six times. Once you have tensioned the spring, use a small screwdriver to keep the pulley from spinning. 5. Attach the cap
How long does it take to fix a recoil starter?
How to replace a spring on a recoil starter?
How to keep a pulley from spinning?
How to thread a rope through a pulley?
How to fix a broken starter?
Why does my lawn mower's recoil starter fail?
Can a small gas engine recoil starter be repaired?
See more
About this website
How do you fix a recoil starter?
0:006:40How to fix a pull starter recoil spring and replace a stuck or limp pull cordYouTubeStart of suggested clipEnd of suggested clipJust kind of have to work it with your pair of pliers the most important thing is. This is whereMoreJust kind of have to work it with your pair of pliers the most important thing is. This is where it's gonna go once it's in there it's gonna go like this. Okay go in there like that you know catch it.
How do you fix a pull start that won't retract?
0:412:58HOW-TO Tighten A Limp Starter Rope That Won't Retract On A Small EngineYouTubeStart of suggested clipEnd of suggested clipI'm just going to turn counterclockwise. One turn on this one if the rope was out further I would goMoreI'm just going to turn counterclockwise. One turn on this one if the rope was out further I would go two turns counterclockwise. And with this recoil here one turn counterclockwise fix.
What if the starter rope won't pull?
0:102:38Lawn Mower Won't Start: Can't Pull the Recoil Starter Rope - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou might have a problem with the recoil starter or the engine might be locked up we'll remove theMoreYou might have a problem with the recoil starter or the engine might be locked up we'll remove the blower housing to check the recoil starter on.
How do you rewind a small engine recoil starter spring?
2:0710:26Best 3 Ways To Install A Recoil Starter Spring On A Small Engine - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe first thing you want to do here is cut the zip tie. Again make sure you're wearing your safetyMoreThe first thing you want to do here is cut the zip tie. Again make sure you're wearing your safety glasses. So now I have to remove it from the casing grab a good pair of pliers.
What causes a pull cord to lock up?
One way the starter cord can get stuck is due to hydraulic lock, which is caused by oil getting trapped in the combustion chamber. You'll need to release the compression and the oil, so remove the spark plug and then give the cord a tug.
How do you lubricate pull start?
3:535:41How To Lubricate A Sticky Starter On A Chain Saw or Weed EaterYouTubeStart of suggested clipEnd of suggested clipRight I usually go on the top when I put a couple good blasts in the in the top in the hole that'sMoreRight I usually go on the top when I put a couple good blasts in the in the top in the hole that's closest to the top blast. It in there like that.
How does a recoil starter work?
Recoil start When the rope's grip is pulled, the rope uncoils, tensions the spring, engages the clutch and turns the crankshaft, spinning it to crank or start the engine before the end of the pull stroke. The running of the engine then disengages the clutch.
Why can't I pull the string on my mower?
If you overfill the crankcase with oil or you store the mower in such a way that it's standing on its front wheels, oil can seep into the piston cylinder and restrict the movement of the piston. When the piston can't move, the crankshaft can't turn and you can't pull the rope.
How do you replace a pull string?
2:033:54How to Replace the Pull Cord on a Small Engine by @Gettin' Junk DoneYouTubeStart of suggested clipEnd of suggested clipBut I've already replaced it you're gonna take this and spin it by hand against the spring. You keepMoreBut I've already replaced it you're gonna take this and spin it by hand against the spring. You keep spinning it over and over. Until you get to the point where you have a lot of tension.
How do you rewind a starter rope on a Briggs and Stratton?
0:007:31HOW TO Repair The Pull Cord on Your Lawnmower With Briggs ...YouTubeStart of suggested clipEnd of suggested clipNow once the three bolts are off just simply remove the cover. Now this recoiled the rope is broken.MoreNow once the three bolts are off just simply remove the cover. Now this recoiled the rope is broken. So all I have to do is to pull the rope out of the eyelet over here.
How do you reset the pull cord on a lawnmower?
3:005:35How to easily fix a lawnmower pull start cord - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou'd have to take it back out again just wind it back up all the way and jam your screwdriver inMoreYou'd have to take it back out again just wind it back up all the way and jam your screwdriver in for the cord lined up undo your simple knot. Let it go back.
How do you fix the pull cord on a leaf blower?
1:483:24How To Fix a Broken Leaf Blower Cord - YouTubeYouTubeStart of suggested clipEnd of suggested clipRun your new cord through the handle. Pull the bad cord out of this plastic piece push in the newMoreRun your new cord through the handle. Pull the bad cord out of this plastic piece push in the new cord tie a small tight knot in it. Pull the cord back down pull it into the handle.
How do you fix a Briggs and Stratton pull start?
0:007:31HOW TO Repair The Pull Cord on Your Lawnmower With Briggs ...YouTubeStart of suggested clipEnd of suggested clipNow once the three bolts are off just simply remove the cover. Now this recoiled the rope is broken.MoreNow once the three bolts are off just simply remove the cover. Now this recoiled the rope is broken. So all I have to do is to pull the rope out of the eyelet over here.
How do you fix the pull cord on a trimmer?
2:114:41How to Replace the Pull Cord of a Weed Trimmer - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo once we get that here we just tie a temporary knot just so we don't lose the strain into. It. SoMoreSo once we get that here we just tie a temporary knot just so we don't lose the strain into. It. So the next thing to do is to pull the string fully out and then check to see.
How long does it take to fix a recoil starter?
Luckily, when this happens, you can fix your recoil starter in about 20 minutes. Your recoil starter may also fail because the pulley or recoil housing has worn and the spring no longer sits in the housing correctly. We used a Briggs and Stratton starter for this repair, but most starters will require the same steps.
How to replace a spring on a recoil starter?
1. Remove the recoil housing cap. Unscrew the cap that holds the pulley to the recoil starter housing. If your spring has slid out of the slots in the housing, then you can continue with the repair. If the housing, pulley or spring have failed, then you will need the proper replacement parts before continuing. 2.
How to keep a pulley from spinning?
With the pulley in the recoil housing, turn it about six times. Once you have tensioned the spring, use a small screwdriver to keep the pulley from spinning. 5. Attach the cap. Reattach the cap that holds the pulley to the recoil housing.
How to thread a rope through a pulley?
Line up the holes on the pulley and the recoil housing and thread the rope through them both.
How to fix a broken starter?
Coil the cord. Hold the recoil starter firmly--it is still under tension--and remove the screwdriver. Pull the starter cord tight and then let go of the pulley. Control the rope speed as the pulley winds the rope back into the starter. Conclusion You can easily repair a broken small engine recoil starter yourself.
Why does my lawn mower's recoil starter fail?
In most cases, the recoil starter fails because the spring slides out of place, causing it to lose tension. Luckily, when this happens, you can fix your recoil starter in about 20 minutes. Your recoil starter may also fail ...
Can a small gas engine recoil starter be repaired?
As anyone who works with lawn equipment knows, small engine recoil starters eventually fail.
How long does it take to fix a recoil starter?
Luckily, when this happens, you can fix your recoil starter in about 20 minutes. Your recoil starter may also fail because the pulley or recoil housing has worn and the spring no longer sits in the housing correctly. We used a Briggs and Stratton starter for this repair, but most starters will require the same steps.
How to replace a spring on a recoil starter?
1. Remove the recoil housing cap. Unscrew the cap that holds the pulley to the recoil starter housing. If your spring has slid out of the slots in the housing, then you can continue with the repair. If the housing, pulley or spring have failed, then you will need the proper replacement parts before continuing. 2.
How to keep a pulley from spinning?
With the pulley in the recoil housing, turn it about six times. Once you have tensioned the spring, use a small screwdriver to keep the pulley from spinning. 5. Attach the cap. Reattach the cap that holds the pulley to the recoil housing.
How to thread a rope through a pulley?
Line up the holes on the pulley and the recoil housing and thread the rope through them both.
How to fix a broken starter?
Coil the cord. Hold the recoil starter firmly--it is still under tension--and remove the screwdriver. Pull the starter cord tight and then let go of the pulley. Control the rope speed as the pulley winds the rope back into the starter. Conclusion You can easily repair a broken small engine recoil starter yourself.
Why does my lawn mower's recoil starter fail?
In most cases, the recoil starter fails because the spring slides out of place, causing it to lose tension. Luckily, when this happens, you can fix your recoil starter in about 20 minutes. Your recoil starter may also fail ...
Can a small gas engine recoil starter be repaired?
As anyone who works with lawn equipment knows, small engine recoil starters eventually fail.
