How to replace a faulty shock cord in a tent pole
- If your cord is still intact, the first thing you need to do is pull apart two sections of your tent pole and use...
- Now you need to measure out the length of the cord to replace the old broken one. If you’re replacing the shock cord...
- Take the loose end of the new shock cord and tie it securely to one grommet...
How do you tie a shock cord to a tent pole?
The knot must be large enough to prevent the shock cord from slipping through the pole. Connect the tent poles. Cut the shock cord from the left end of the first pole piece leaving room on the end for knots. Leaving extra shock cord on the end will also allow you to adjust the tension in the shock cord later on.
How do you fix a tent pole that won’t stay up?
If the cord hasn’t broken, and rather it’s too stretched out for your tent pole, there’s an easy fix. Just remove the peg from one end of your poles and untie the cord. Then, pull through the shock cord until it’s taught once again, and retie it at the grommet peg.
What should I do if the shock cord is too tight?
If the shock cord is too tight, reconnect the poles and adjust the shock cord length between the left end of the first pole and the end piece. Almost done! To reassemble your device, follow these instructions in reverse order.
Why does my tent pole shock cord not work?
Tent pole shock cords can easily malfunction, over time they deteriorate and become brittle, and eventually lose their elastic properties. When the shock cord in your tent pole doesn’t function anymore, you might think new poles need to be purchased. However, buying new tent poles can be very costly, and there’s a much cheaper alternative.
How long should shock cord be for tent pole?
You will need 1/8” thick shock cord and about 1-2 ft. longer than the length of the entire pole for each pole (if you have a 10ft pole get about 12ft, some say a ¾ 1. ratio might be better). Remove the end tip, and the shock cord will be tied in a knot (either on a washer or on the end tip of the pole).
How do you fix the elastic in a tent pole?
1:354:58How To Repair Tent Pole Elastic - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo use a screwdriver to clear that away that should expose the knot inside. Which you can then takeMoreSo use a screwdriver to clear that away that should expose the knot inside. Which you can then take the tweezers with remove untie the knots. And then clear away the old elastic.
How do you use a tent pole repair tube?
0:072:27Tent Pole Repair Tips - YouTubeYouTubeStart of suggested clipEnd of suggested clipSection flatten any rough areas that keep the repair sleeve from sliding into place if you have ductMoreSection flatten any rough areas that keep the repair sleeve from sliding into place if you have duct tape with you wrap the ends of the tube a few times to keep it in place. If.
Can you repair a tent pole?
The easiest and quickest way to fix a broken pole is with a pole repair sleeve. Also called a splint, this short tube is often provided with your tent. If not, buy one and pack it with you. A good pole repair sleeve is just slightly larger in diameter than your pole so that it doesn't move around too much.
Are shock cords elastic?
A bungee cord (sometimes spelled bungle; also known as a shock cord) is an elastic cord composed of one or more elastic strands forming a core, usually covered in a woven cotton or polypropylene sheath.
What is a tent pole repair sleeve?
0:031:13How to Use a Pole Repair Sleeve | NEMO - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can hopefully repair it and continue using that tent with this repair accessory to use it goMoreYou can hopefully repair it and continue using that tent with this repair accessory to use it go ahead and slide it on the end of the pole length that's closest to the break in the pole.
How do I fix my camping tent pole?
0:184:55How to repair a broken tent pole - YouTubeYouTubeStart of suggested clipEnd of suggested clipA key thing here is you don't want the shock cord to get trapped. And. So you can see there it'sMoreA key thing here is you don't want the shock cord to get trapped. And. So you can see there it's coming out trying to come outside you wanna make sure it's in the middle of the thing.
How do you use a tent pole splint?
0:140:58How to use your repair splint - YouTubeYouTubeStart of suggested clipEnd of suggested clipStep one to properly use your pole splint. Simply slide the splint over the broken pole segment.MoreStep one to properly use your pole splint. Simply slide the splint over the broken pole segment.
How do you replace a tent pole section?
0:093:56How To Repair A Broken Tent Pole Section - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you simply need to measure mark. And cut the pole down with a hacksaw. And then with a sandpaperMoreSo you simply need to measure mark. And cut the pole down with a hacksaw. And then with a sandpaper just remove any sharp edges this will prevent them from damaging the elastic in your pole sections.
How do you repair Aluminium tent poles?
1:287:43How to Repair a Broken Tent Pole - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou're getting a fiberglass tampo repair kit if you're fixing aluminium lightweight tents or a swagMoreYou're getting a fiberglass tampo repair kit if you're fixing aluminium lightweight tents or a swag swagg pole then you get a swag pole replacement kit.
How do you repair a Coleman tent pole?
3:0712:48How to Repair a Broken Tent Pole - Coleman Replacement Kit - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe have a nice replacement pull section cut down to the right level a quick note about the shockMoreWe have a nice replacement pull section cut down to the right level a quick note about the shock cord if I really wanted to I could probably salvage the old cord and reuse it in the repaired pole.
How do you replace a tent pole section?
0:093:56How To Repair A Broken Tent Pole Section - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you simply need to measure mark. And cut the pole down with a hacksaw. And then with a sandpaperMoreSo you simply need to measure mark. And cut the pole down with a hacksaw. And then with a sandpaper just remove any sharp edges this will prevent them from damaging the elastic in your pole sections.
How do you fix a swag pole?
1:287:43How to Repair a Broken Tent Pole - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo if you're fixing a fiberglass tentpole. You're getting a fiberglass tampo repair kit if you'reMoreSo if you're fixing a fiberglass tentpole. You're getting a fiberglass tampo repair kit if you're fixing aluminium lightweight tents or a swag swagg pole then you get a swag pole replacement kit.
How do you restring a Coleman tent pole?
2:5910:30Coleman Tent Pole Repair Kit - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then came to the end and then wrap some white duct tape around it. That's gonna help me seeMoreAnd then came to the end and then wrap some white duct tape around it. That's gonna help me see where I need to cut it now all I have to do is take her hacksaw. And cut it at this line right here.
How do you tighten a shock cord?
0:281:27How To Tighten a Loose Bungee Cord - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou know pretty close to the other knot tighten it and then simply snip off that end that you don'tMoreYou know pretty close to the other knot tighten it and then simply snip off that end that you don't need to pull it back out to release it from that little notch let it go and then you'll find that.
Introduction
This guide will illustrate how to replace the shock cord in tent poles with a bobby pin and string. There are many other methods that can be used to feed the shock cord through tent poles, but when away from home, a bobby pin and string can save the day.
Step 6
Drop the bobby pin and string through the tent pole pieces one by one.
Step 7
Once the last piece has been threaded, untie or cut the string from the shock cord.
Step 9
Cut the shock cord from the left end of the first pole piece leaving room on the end for knots.
Step 11
To reassemble your device, follow these instructions in reverse order.
What is the peg on a shock cord?
There should be a peg, called a grommet peg, at either end of the poles; remove these, and you’ll see the old shock cord tied on.
How to make a tent as good as new?
If your cord is still intact, the first thing you need to do is pull apart two sections of your tent pole and use scissors to sever the shock cord inside. Once the cord is cut, your tent pole will fall apart into its different sections.
What is the purpose of shock cords in tent poles?
Modern tent poles contain shock cords, their main purpose is to keep your tent poles attached together. Earlier tent designs featured poles which simply broke apart into smaller sections, while this modern improvement keeps all your poles in one piece and makes pitching your tent easier.
Can you set tent poles down on the ground?
If you’ve made a repair to your tent pole shock cord, and want to avoid having to do the same again in the future, we have some advice on preserving and extending the life of your tent poles. At any time, avoid setting your poles down on the ground, especially in loose dirt, gravel, or mud.
Can a tent pole break?
How to repair a broken tent pole. The shock cord isn’t the only thing that can break on your tent pole; sometimes, the outer poles themselves can be prone to breakage. If you suffer from a tent pole breakage when out on a camping trip, it can make your shelter completely useless!
Can you use string to replace a tent pole?
Using string as a temporary replacement for a broken shock cord. If the shock cord in your tent pole is beyond repair, but you don’t have a new replacement cord on hand, you can use a string to attach your poles together.
Can you use shock cords on a tent?
It’s also much easier to lose components of your tent and poles when they aren’t attached together, so shock cords are very useful in this regard.
How to tie a shock cord?
Tie a knot in one end of the shockcord, then feed the other end through all but the last pole section. Stretch the shockcord to extend its length, then tie a temporary knot to keep it from slipping back inside the second-to-last pole section; alternatively, you can use a pair of locking pliers to hold the cord.
How to replace shockcord on tent pole?
Fortunately, replacing it is a straightforward process. Here’s what you’ll need: Here’s how to replace the shockcord: Start by laying the tent pole out straight. To avoid mixing up sections, you can label them with a permanent marker (use masking tape if you don’t want to write directly on the pole.)
How to fix a broken tent pole?
Using a repair sleeve to fix a broken tent pole is simple: Line up the broken pole sections. If the pole is bent but not fully broken, gently straighten out the bend. Slide the sleeve over the pole end until it’s centered over the break or kink; you might have to use pliers to crimp or a rock to bend splayed pieces so that ...
What happens if a tent pole breaks?
If your pole breaks where one pole end inserts into the next one, you will have to splint the sections together; keep in mind that this will prevent the poles from folding up neatly when you take the tent down.
What to do if a tent pole gets stepped on?
Whether your tent pole gets stepped on or a powerful gust of wind does the damage, a kinked, split or snapped pole needs immediate attention in the field (when you get home, you can look into having the pole replaced or professionally repaired.) You have two options: Use a pole repair sleeve. Use a tent stake as a splint.
What is a splint for a tent pole?
Also called a splint, this short tube is often provided with your tent. If not, buy one and pack it with you. A good pole repair sleeve is just slightly larger in diameter than your pole so that it doesn’t move around too much. Using a repair sleeve to fix a broken tent pole is simple: Line up the broken pole sections.
Can you use a shockcord pole in the field?
If the shockcord snaps while you’re in the field, you can still use the pole by carefully assembling the individual sections. However, when you get home, you’ll want to replace the shockcord; it makes assembly simple and keeps you from losing a pole section. Fortunately, replacing it is a straightforward process.
What size shock cord is in tent poles?
What you’ll need: Shock Cord (1/8″ or smaller). You need at least the length of all your poles combined.
How do you tie a tent shock cord?
Tie a large knot around the tent pole end piece. Fit the end piece into the left end of the first pole. If your poles do not come with an end piece, simply tie a large knot in the shock cord. The knot must be large enough to prevent the shock cord from pulling through.
Why are guy ropes so called?
People also (mistakenly) call it guide wire. The name guy wire is derived from the term guy: defined as a rope, cord or cable used to steady, guide or secure something. Guy wire is a tensioned cable that is both lightweight and strong.
How can I make my tent more stable?
Start with your tent body and stake it down, starting with the windward side. Don’t push your stakes straight down but rather at 45 degrees which makes them more secure. Put rocks on the tent to help hold it down while you stake it around. Use more rocks to keep the stakes down.
Can you fix a broken tent pole?
The easiest and quickest way to fix a broken pole is with a pole repair sleeve. Also called a splint, this short tube is often provided with your tent. If not, buy one and pack it with you. A good pole repair sleeve is just slightly larger in diameter than your pole so that it doesn’t move around too much.
Can one person put up a tent?
There is no need to be intimidated. Even though dome tents look difficult to set up alone, they are actually one of the easiest tents to assemble by yourself! If you have a newer dome tent, it is simpler than ever to put one together.
How do you melt a shock cord?
Use something simple like a lighter (some people use heat guns) to melt the elastic ends together. Assuming that material allows this, fusing after you put the cord in a knot will help create a stronger bond.
Why do tent poles fail?
All tent poles are bound to fail at some time due to wearing of the elastic bungee cord around the end of the tent pole aperture. So before you even think of throwing the tent away look at this process which allows you to fix them with ease. You can also step to the video here:
How long should a tent wiper blade be?
The best wiper blades are those from a saloon car or a van for the best length. Ideally you need wiper blades of length around 50cm - 52 cm so they are just longer than a single pole of the tent pole assembly.