
Concrete Floor Toilet Flange Replace
- If the flange is any higher than about 3/8" (depends on the particular toilet) then the toilet won't fit flat on the...
- The hot line and cold line are spaced 8 inches apart (from left to right). Measure from your back wall to the closet...
- Gapper Flange • Used to repair. Select from a variety of new and replacement toilet flanges...
Full Answer
How to fix a broken toilet flange in concrete?
Instructions
- Cut off the Old Flange and Obstructions. After you remove the toilet, you will probably find an existing toilet flange. ...
- Scrape off Old Wax Ring. ...
- Pick the Correct New Toilet Flange. ...
- Place T-Bolts in New Toilet Flange. ...
- Position Toilet Flange. ...
- Drill Holes Into Concrete. ...
Can a toilet be properly installed without a flange?
The toilet flange needs to be on top of the finished floor. Meaning the bottom edge of the flange needs to be on the same plane as the toilet. So if your toilet sits on the tile, the flange needs to be on top of the tile too. Can a toilet be properly installed without a flange? 2 Answers.
How to unclog a toilet with a flange plunger?
Unclogging the Toilet Using a Plunger
- Keep Stagnant Water in the Toilet Bowl. Ensure there is pooled water in the toilet bowl. ...
- Pull Out the Flange of the Plunger. If your flange plunger has the capped part, make sure that it’s completely pulled out of the cap. ...
- Fit the Cup over the Hole of the Drain. ...
- Grab the Plunger with Both Hand and Push. ...
- Pull the Cup of the Whole On the Last Thrust. ...
How to attach a toilet to a concrete floor?
Required Materials for this Project
- Caulk
- Masking tape
- Paper towels
How do you replace a broken toilet flange on a concrete floor?
1:313:52How to Fix a Toilet - Cement Sub-Flooring Repairs - Part 1 of 2YouTubeStart of suggested clipEnd of suggested clipItself the second way to fix this problem is to cut out the damaged flanges metal ring leaving theMoreItself the second way to fix this problem is to cut out the damaged flanges metal ring leaving the ABS coupling and install an inside fitting flange. The reason this technique is suggested.
How do you repair a concrete toilet flange?
1:423:22How to Fix a Toilet - Cement Sub-Flooring Repairs - Part 2 of 2YouTubeStart of suggested clipEnd of suggested clipApply ABS glue to the inside of the sewer inlet. And also to the replacement flange insert the newMoreApply ABS glue to the inside of the sewer inlet. And also to the replacement flange insert the new flange into the sewer inlet. Once the flange is position with the mounting channels at the 9.
How do you glue a toilet flange to a concrete floor?
0:223:45How to Fix a Toilet - Cement Sub-Flooring Repairs - Part 1 of 2YouTubeStart of suggested clipEnd of suggested clipAnd the toilet flange is inserted into the sewer. Inlet. Pilot holes are then drilled into theMoreAnd the toilet flange is inserted into the sewer. Inlet. Pilot holes are then drilled into the cement. And then the cement screws installed securing the flange to the cement slab.
What do you use to anchor a toilet flange to a concrete floor?
Use Tapcon anchors or a similar type of masonry/concrete screw to fasten the toilet flange to the concrete slab. If using a plastic flange ring, be careful not to crack the ring by screwing the anchors in too far. With the toilet flange in place, you are ready to install the toilet with a new wax ring.
Can you put a new toilet flange over an old one?
Apply a generous bead of 100% silicone caulk on top of the old closet flange. And to the bottom of the new closet flange extender. Either slide the new closet flange bolts into the old flange before adding the extender or add them after you adhere the extender to the old flange.
How do you fix a PVC toilet flange in concrete?
4:5710:54How to Replace a Broken PVC Toilet Flange (Start to Finish) - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd make sure that it's a smooth bit and now I'll go ahead and glue it you want to install. TheMoreAnd make sure that it's a smooth bit and now I'll go ahead and glue it you want to install. The flange so when it's down in there it's sitting just the height of the flange off the floor.
Does a toilet flange need to be glued?
If the pipe has a 4-inch inside diameter: This toilet flange is designed to glue on the inside of the pipe or expand inside the pipe. Leave the old toilet flange right in place and glue on the new one at the right elevation for the floor, if it's plastic.
Does a toilet flange need to be screwed to the floor?
Closet (toilet) flanges must be 1/4" above a finished floor. This is so the wax ring seals properly to the flange and the hub on the toilet. If a proper seal is not achieved it will result in leaking. If the flange is lower than or flush with the floor they make foam rings that cover the distance for a proper seal.
How do you replace a cast iron toilet flange in concrete?
0:1138:04Replacing a Cast Iron Toilet Flange Part 3 - YouTubeYouTubeStart of suggested clipEnd of suggested clipI've now got most of the concrete. That's over the top of the toilet flange out of the way chiseledMoreI've now got most of the concrete. That's over the top of the toilet flange out of the way chiseled it out i've got the lead exposed.
How do you bolt a toilet to a concrete floor?
Step 1: Place the Flange. Place the toilet flange face down on the concrete. ... Step 2: Drill Holes for the Flange. Next, use a marker to mark the concrete right where the four holes in the flange are. ... Step 3: Clean the Area. ... Step 4: Attach the Flange. ... Step 5: Finish the Flange Installation. ... Step 6: Connect the Toilet.
How do you secure a toilet flange to the floor?
0:594:12How to Install a New Toilet Flange | Ask This Old House - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing an old shim. Good. This is actually a compression flange. We're going to be using a rubberMoreUsing an old shim. Good. This is actually a compression flange. We're going to be using a rubber gasket and that will make a nice tight seal between the bend. And the flange.
How do you install a toilet without breaking concrete?
0:020:37How to Add a Toilet in The Basement Without Breaking Concrete in ...YouTubeStart of suggested clipEnd of suggested clipIt was easy and we save so much money because we didn't have to break the floor or fanic la masaMoreIt was easy and we save so much money because we didn't have to break the floor or fanic la masa raiders and pumps can be used anywhere in the home you can also install a bathroom in the garage.
How do you replace a cast iron toilet flange in concrete?
0:1138:04Replacing a Cast Iron Toilet Flange Part 3 - YouTubeYouTubeStart of suggested clipEnd of suggested clipI've now got most of the concrete. That's over the top of the toilet flange out of the way chiseledMoreI've now got most of the concrete. That's over the top of the toilet flange out of the way chiseled it out i've got the lead exposed.
Does a toilet flange need to be glued?
If the pipe has a 4-inch inside diameter: This toilet flange is designed to glue on the inside of the pipe or expand inside the pipe. Leave the old toilet flange right in place and glue on the new one at the right elevation for the floor, if it's plastic.
How do you install a toilet offset flange on concrete?
0:197:48Toilet Flange Repairs in Cement Offset Toilet Flange - YouTubeYouTubeStart of suggested clipEnd of suggested clipPlace now if you're way off then you might have to just break the floor out and actually moveMorePlace now if you're way off then you might have to just break the floor out and actually move fittings and we'll look at that in just a minute. But if you're a little bit off. Say one to two inches.
How do you remove an outside toilet flange?
1:044:12How to replace a flange outside the pipe | Toilet flange replacementYouTubeStart of suggested clipEnd of suggested clipAnd then just drill it around do the four or five drills. Now carefully using the flat screw driver.MoreAnd then just drill it around do the four or five drills. Now carefully using the flat screw driver. I'm gonna put it between these two rings. And using my hammer. And i'm gonna knock. It.
How do you install a toilet flange on a concrete floor?
Cut off the Old Flange and Obstructions. After you remove the toilet, you will probably find an existing toilet flange.
What happens if toilet flange is broken?
If the toilet rocks because the flange is no longer holding it securely, the wax ring seal can break, water can begin to seep out and problems quickly multiply.
Should a toilet flange be flush with the floor?
The toilet flange needs to be on top of the finished floor. Meaning the bottom edge of the flange needs to be on the same plane as the toilet. So if your toilet sits on the tile, the flange needs to be on top of the tile too. The spacing of the toilet exit “horn” and sealing surface is designed for this height.
Do you put the wax ring on the toilet or the flange?
Place the wax ring on the closet flange, not on the toilet. Then, pick up the toilet and set it evenly over the closet flange, making sure the bolts come through the bolt holes in the toilet base. Fine-tune the toilet position, so it’s right where you want it, then push it straight down so it smashes the wax evenly.
How do I know if my toilet flange is bad?
If you notice a lot of water pooling at the base of your toilet and inspect to find that your flange is cracked or broken, it’s time for a replacement. Signs of potential flange damage:
Should I replace toilet wax ring?
It requires no maintenance and can last 30 or more years, often as long as the toilet itself. But sometimes wax rings can dry out, crumble, and fail prematurely. When that happens, they need to be replaced. The telltale sign of wax ring failure is water leaking out from around the base of the toilet.
Should PVC toilet flange be glued?
pvc flange should be glued into a pvc pipe. IT would have been less of a problem if a plumber had made the replacement. Use a “good” flange and you will not have to do it again. Caulk is NOT glue.
How do you fix a broken toilet flange?
Hook the heads of the closet bolts to the underside of the repair plate, repair ring or push-in replacement and center them in the tracks. Place a new wax ring on the flange opening, replace the toilet and bolt it to the flange. Replace the supply hose and turn the water back on.
What causes a toilet flange to break?
Many times an uneven floor and uneven setting of the toilet leads to rocking which then leads to a broken flange. The tendency is to either double up on the new wax ring or use flange spacers to beef up to proper height.
Should a toilet flange be flush with the floor?
The toilet flange needs to be on top of the finished floor. Meaning the bottom edge of the flange needs to be on the same plane as the toilet. So if your toilet sits on the tile, the flange needs to be on top of the tile too. The spacing of the toilet exit “horn” and sealing surface is designed for this height.
Do you put the wax ring on the toilet or the flange?
Place the wax ring on the closet flange, not on the toilet. Then, pick up the toilet and set it evenly over the closet flange, making sure the bolts come through the bolt holes in the toilet base. Fine-tune the toilet position, so it’s right where you want it, then push it straight down so it smashes the wax evenly.
Should PVC toilet flange be glued?
pvc flange should be glued into a pvc pipe. IT would have been less of a problem if a plumber had made the replacement. Use a “good” flange and you will not have to do it again. Caulk is NOT glue.
Should you caulk around a toilet?
Some people prefer to caulk all around the toilet and leave about a one -inch gap in the caulk at the back of the toilet to allow water to escape out in the event of a leak .
Will a broken toilet flange cause a leak?
For example, a rocking toilet can crack the wax ring. When the wax seal is broken, you’ll have water leaking from the toilet.
How long does it take to replace a toilet?
Even beginner DIY plumbers find that they can remove the old toilet and put in the new toilet in less than an hour, as long as there are no complications.
What happens if you remove a wax ring from a drain?
After you remove the obstructions, the old wax ring will still be in place around the drain opening. The wax most likely will be thick, sticky, and possibly stained with sewage. Removing the wax ring requires patience, a putty knife, and latex gloves.
What tool do I need to drill into masonry?
If you expect to drill into masonry more often, purchase a good-quality tool, such as a Bosch, Hilti, DeWalt, or Milwaukee hammer drill. Because the old bolts will need to be cut off, you'll need some type of power tool to do the job. A manual hacksaw will not work, because you need to move the saw blade against and parallel to the concrete slab.
Can you rotate a toilet flange?
You can rotate the flange in either direction until you have reached the preferred position. After the toilet is placed, you will still have the opportunity for some minor rotation, but it is still best to get the position as straight as possible before securing the flange. Lee Wallender.
Can you use a hacksaw to cut concrete?
A manual hacksaw will not work, because you need to move the saw blade against and parallel to the concrete slab. Either an oscillating multi-tool equipped with a metal-cutting blade or an angle grinder will do the trick.
Can you keep old bolts in place?
If the old bolts are in good condition and match up perfectly with the new flange, you can keep them in place to secure the new flange. But if the bolts are unacceptable (too rusted, mismatched, too short, etc.), they must be cut off before installing the new flange.
How to stop a toilet from leaking?
Use a water absorber, like LiquiLock, to temporarily solidify the remaining water, turning it into a gel, which will help prevent drips and leaks when removing the toilet fixture. The gel will dissolve when additional water is added.
How do I reinstall a toilet?
Reinstall toilet by using Johni-bolts (the bolts that connect the toilet to the floor) as a guide. Make sure you hold the toilet as level as possible when placing it onto the new wax seal. The toilet tank should be parallel to the wall behind it.
Can you rock a toilet?
Do not rock the toilet as it is placed on the new wax seal. Use a slight side-to-side twisting motion until the toilet bowl is resting on the bathroom floor.
Can you use knockout plugs on cast iron?
For new construction or remodels, there are flanges with knockout plugs that allow you to test the system without having to use a test ball or plug, while also keeping sewer gases from escaping.
Can you repair a toilet flange?
The good news? With the proper tools, a little know-how and a trip to the local hardware store, most people can effectively repair their own toilet flanges without breaking a sweat (or the bank!)
