Repairing Guides

how to repair top load washing machine

by Miss Marian Kassulke Published 1 year ago Updated 1 year ago
image

How to fix the top-loading washing machine shakes problem?

  • Remove foreign objects in the tub if president.
  • Check the drive belt for damage and replace it if damage
  • Clean and lubricate the idler pulley and the motor pulley.
  • Check for loose parts if you find any parts loosen then tight the parts by screw drivers or hex wrench.
  • Check the screws that hold the idler pulley and...

Full Answer

How do you open a top loading washing machine?

How to Take the Top Off a Maytag Washer

  1. Safety First. Remember that these appliances conduct electrical currents. ...
  2. Lower-Front Screws. As you go through this process, you will see that it is largely about removing screws. ...
  3. Front Panel. ...
  4. Lifting the Front Edge. ...
  5. Machine Bolts. ...
  6. Returning Everything. ...

How do I keep my front load washing machine clean?

Part 3 Part 3 of 3: Maintaining a Front Load Washer

  1. Use the right detergent. Purchase a detergent that's specifically designed for use in an HE machine.
  2. Remove your laundry right after it is done. Don't let your clean wet clothes stay in the washing machine for hours before switching them to the dryer.
  3. Dry the gasket in between loads. ...
  4. Remove and air dry the dispenser tray. ...

How to effectively clean a washing machine?

How to clean front load washing machines

  • Run a hot cycle with an empty machine to remove any built up detergent.
  • Wash on a 40 degree wash with a washing machine cleaner to get rid of odours.
  • Remove the detergent drawer and soak it in a bowl or sink. ...
  • Wipe the machine and door down with a cloth dampened with hot water. ...
  • Wipe inside the hole where the dispenser drawer was located.

More items...

How to clean your front loader washing machine?

Steps:

  1. Be sure the washing machine is empty. If your washer has removable detergent or fabric softener trays, remove those and clean them with hot water and a small brush. ...
  2. Put a washing machine cleaning tab or powder in the empty washer. ...
  3. If your washer has a dedicated cleaning cycle, you can use that. ...

More items...

image

How do you troubleshoot a washing machine problem?

Washer Troubleshooting GuideCheck that the washer is plugged in securely.Check the circuit breaker or fuse box.Test the outlet for current.Check that the water supply valves are turned on.Inspect the filter screens.Test for overheating.Test the water level switch.Test the timer control.More items...

What are common problems with washing machines?

10 Most Common Washing Machine ProblemsIt Bounces Around. ... It's Noisy. ... Clothes Are Getting Ripped. ... Improper Or Slow Draining. ... My Washing Machine Won't Spin. ... There's No Water. ... The Door Won't Open. ... It's Smelly.More items...

What causes a top loader washing machine to stop spinning?

The lid switch isn't working properly If you're dealing with a top-loading washer not spinning, an impaired lid switch is one of the most common causes and should be one of the first things you check, especially if your issue is a top-loading washer that fills and agitates, but doesn't spin properly.

How do you service a top loader washing machine?

0:573:13How to Clean Your Top-Loading Washing Machine - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhite vinegar. Between the bleach and the white vinegar it will clean away the bacteria. The soapMoreWhite vinegar. Between the bleach and the white vinegar it will clean away the bacteria. The soap scum the hard water deposits all that dirt and grime that builds.

Is it worth repairing my washing machine?

As a general rule, if it costs less than 50% of the price of a new washing machine to repair your old one, you should choose the repair option. But, you should also consider whether or not there is a warranty coverage on your washer and think about economic realities.

How many years should a washing machine last?

around 10 yearsWashing machines, on average, last around 10 years, according to Consumer Reports. If your washer is reaching the threshold, or it's been having some problems, here are some signs the end may be near.

What causes a washing machine to not spin and drain?

If the washer won't drain or spin, either something is stuck in the washing machine drain hose or pump, or the pump is broken.

How do I fix a washing machine that will not spin?

Redistribute an off-balanced load of laundry. ... Level an off-kilter washer. ... Check the power source. ... Stop using an extension cord. ... Inspect the spin switch. ... Stick to high efficiency detergent with a front-load washer. ... Undo any kink in the hose. ... Track down a blockage in the drainage system.More items...•

Why is my washer not spinning or draining?

If your washer won't drain or spin, the water level control may be faulty. Open the machine's control panel and look for a plastic tube attached to the water level valve. If it's clogged, clear it out with vinegar. If the valve itself is corroded, it may need to be replaced.

Where is the drum on a top load washing machine?

The drum of the washer is the basket that holds clothes and the post in the middle around which the basket spins. The issue, of course, is that if clothes are loaded in an unbalanced way around the drum, it won't spin freely and evenly. The drum will tilt to one side and begin scraping in it's track instead of guiding.

Where is the drum in a top loader?

The one you see where the clothes are loaded is the inner drum, which moves around the washing machine and is perforated with holes to allow the water in and out. The outer tub contains the inner drum and the water, stopping it from leaking into the rest of the machine and supports the inner drum. Agitator or paddles.

Do top load washers need to be cleaned?

Every type of top-load washer should be thoroughly cleaned at least twice per year. If you have automatic dispensers and use them for each load, they should be cleaned monthly to prevent clogs.

Is there a reset button on washing machines?

Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. Causes that lead to these problems include power spikes, imbalanced loads or an interruption in power. Some machines have a button you push to reset its motor.

How do I reset my washing machine?

1:243:47Washer Not Spinning - How to Reset Motor (Easy) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe machine gives you 30 seconds to lift the lid and close. It six times and once you start liftingMoreThe machine gives you 30 seconds to lift the lid and close. It six times and once you start lifting the lid. You have 12 seconds to do the six repetitions.

Why won't my washing machine finish its cycle?

Some of the most common faults that will make your washer stop mid cycle include thermostat failure, problems filling up with water for the rinse cycle, or even pump problems that prevent your washer from draining. One thing that you can check yourself is the lid switch.

THE WASHING MACHINE WON’T DRAIN

If your washing machine won’t drain or your loads are coming out too wet, you may have a kink or clog in the drain hose, a drain pipe that’s too lo...

MY WASHING MACHINE WON’T SPIN

A washer needs to spin correctly in order to fully rinse clothes and drain water from the tub. Before scheduling a service call, check if the power...

WASHING MACHINE IS LEAKING

Water is meant to stay in the washer. But if you’re noticing some water appearing on the floor, it may be a simple fix. Try cleaning the door seal,...

MY WASHER IS NOISIER THAN EXPECTED

If you’ve just brought home a new washer, it’s possible that it makes some noises you aren’t familiar with. Many of these are normal and shouldn’t...

MY WASHER HAS ODORS

Washer odors are easily fixable and usually the result of a missed cleaning, a load left too long or too much detergent and fabric softener use. Tr...

How to fix water on floor in washer?

But if you’re noticing some water appearing on the floor, it may be a simple fix. Try cleaning the door seal, tightening hose connections and cleaning the drain pump filter.

What to do if your washer spins but doesn't spin?

In this case, turn on a spin cycle or drain and spin cycle to get rid of the remaining water.

How high should a drain pipe be on a Maytag washer?

For most Maytag ® washers, the drainpipe should be installed at a maximum of 96" and a minimum of 39" from the bottom of the machine . Your washer will not be able to adequately pump water out of the washer if the drainpipe reaches too high. In this case, water may flow back into the washer. Consult your washer's installation instructions for model-specific installation requirements or watch this video on proper drain hose and drainpipe installation for Maytag ® washers.

Why do washers spin?

A washer needs to spin correctly in order to fully rinse clothes and drain water from the tub. Before scheduling a service call, check if the power has gone out, that your load is balanced and that the washer is level.

How to contact Maytag for repair?

If you need professional repair help, schedule service online or call 1-800-344-1274.

Why does my washer make a hum?

It’s normal to hear the pump or motor make a continuous humming sound while loads are washing, along with periodic gurgling or surging as water is removed during the spin or drain cycles . You may also hear the hum of the sensing spins after you have started the washer.

Why does my washer make a clicking noise?

Many washer lids make clicking noises while they’re locking in place at the beginning of a cycle. It’s also normal to hear metal items on clothing like buckles or zippers touch against the stainless steel basket. Always empty your pockets before putting clothes in the washer—it’s possible for coins or other items to fall between the basket and the tub, which may require a service call.

How old is a 2021 washer?

It’s September of 2020, and in January of 2021, that washer is six years old. I haven’t touched the washer for any reason. It is never overloaded and doesn’t see king-size blankets, etc. It runs great, isn’t noisy, doesn’t leak, and shows no signs of slowing down.

What Exactly is Too Much Weight?

That’s a question I get almost every day. With washers today, a hefty dose of common sense applies. As a general rule of thumb for every load, a basket that is half-full of clothes is a standard size load for a top load. A front-load washer is a little more forgiving. After loading your clothes, you should see only about eight inches of clearance between the top of the basket and the top of the load. There are no exceptions to this rule. Please, heed the warning here. Too much weight causes early problems with your washer. Your washer today is nothing like the washers of fifteen years ago. Not even close.

Can you opt out of a washer repair?

Or, you can opt-out of the repair entirely and replace the washer. But, is that what DIYers do? The DIYers I talk to love to save money, and this is one of those times when you will save a LOT of money by doing it yourself.

Is it worth it to run a washer?

Yes, it’s a lot of work, but it is worth the time and effort. When finished, you’ll have a great running washer and still have money left in your pocket.

Can a standard size load be used in a washer?

A standard size load is no problem for the washer and will do fine for years with that kind of use.

How to fix the top-loading washing machine shakes problem?

To reduce your washing machine from shaking, you should check the leveling of the machine. If this is not the case, you may tighten the nuts that hold the legs of your washing machine.

How to know your washing machine shock absorber is damaged?

You just need to know your model and check out their official sites to know where the shakes remover is placed in your washing machine.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9