How to Fix a Lift-Bucket Drain Stopper
- Remove the Cover Plate and Stopper. Back out the mounting screws that hold the overflow cover plate onto the overflow tube. ...
- Adjust the Linkage. If necessary, adjust the linkage to lengthen the connecting rod. ...
- Reassemble the Stopper. Insert the stopper and drain linkage back down through the overflow opening. ...
Full Answer
How to remove and replace a bathtub drain stopper?
- Push the stopper handle all the way down to expose the bottom of the stopper linkage underneath the sink.
- Locate the tension clip that secures the clevis to the stopper linkage.
- Disconnect the clevis from the stopper linkage.
- Remove the clevis from the sink's drainpipe.
- Lift the stopper out of the sink.
How do you remove the stopper from a tub?
- Place a towel in the bottom of the bathtub to protect the tub's finish while you work.
- Lift the toe-tap stopper with your fingers until it will lift no farther.
- Pull upward on the stopper as you turn it counterclockwise if the stopper only spins instead of unscrews from the drain.
How to get the drain plug out of a tub?
- The faceplate will be on the tub wall near the faucet, not on the bottom of the tub with the drain.
- These type of drains will stop a tub when a trip lever is activated. ...
- Set the tip of the screwdriver underneath the lip of the loosened drain if you need some leverage as you pull it out.
- Make sure to pull away from the tub wall.
How to unstop a bathtub drain?
Method 4 Method 4 of 5: Using Chemical Drain Cleaners
- Buy a chemical drain cleaner from the store. Chemical drain cleaners unclog drains with chemicals such as potassium hydroxide or sulfuric acid.
- Read the instructions on the back of the cleaner. These are the manufacturer’s instructions, and all drain cleaners will have slightly different ones.
- Remove any standing water from the bathtub. ...
How do you fix a broken bathtub drain stopper?
1:423:06Replacing Tub Drain with BROKEN T! - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis point I'm taking my hammer. And I'm hitting the screwdriver underneath the tub drain. And whatMoreThis point I'm taking my hammer. And I'm hitting the screwdriver underneath the tub drain. And what I want to do is I want to cut you know.
How do you repair or replace trip lever drain stopper?
3:0711:15Bath tub trip lever/ bath tub stopper replacement or adjustnmentYouTubeStart of suggested clipEnd of suggested clipYou just pull this thing out over there. And you put your new plate on there put the cotter pin andMoreYou just pull this thing out over there. And you put your new plate on there put the cotter pin and throw this back in so this isn't really that dirty.
Can a tub stopper be replaced?
Buy a new lift-and-turn stopper to replace your old lever-style drain. When the stopper in your lever-style bathtub drain won't pop up anymore because the linkage is damaged or clogged, replace it with a much simpler lift-and-turn style tub drain.
How do you replace a tub lift and turn stopper?
1:012:14Removing a lift-&-turn stopper (1-step) - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut basically you'd grip it underneath that top part and just grip it tight turn it once he getsMoreBut basically you'd grip it underneath that top part and just grip it tight turn it once he gets loose. Enough. Just keep turning. And it comes out.
How do you fix a twist handle bath control mechanism?
0:041:34How to fix a twist handle bath plug mechanism - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf we take it off you can see it's actually just a screw on the top there. That's have to be comingMoreIf we take it off you can see it's actually just a screw on the top there. That's have to be coming loose.
How do you replace a bathtub drain flange?
6:1011:39Replacing a Tub Drain: Bathtub Drain Removal and ReplacementYouTubeStart of suggested clipEnd of suggested clipTightening always start the drain off hand tight to ensure it isn't being cross threaded snug up theMoreTightening always start the drain off hand tight to ensure it isn't being cross threaded snug up the drain with a wrench clean up the plumber's putty and then reinstall.
How do you remove a pop up drain stopper?
Pop-upTechnique #1: Grasp the drain stopper by squeezing each side. Pull the drain stopper up until it comes out. ... Technique #2: Twist counterclockwise to unscrew the cap. Next, use a screwdriver to unscrew the base underneath. ... Technique #3: This works for a rocker arm pop-up stopper.
How do you remove a trip lever drain stopper?
How to Remove a Trip-Lever Drain Stopper:Set the drain to its open position.Unscrew the faceplate that is mounted to the overflow drain.Pull the faceplate free and the rest of the drain stopper's connected hardware should follow. ... You may need to wiggle the drain stopper to free its entire length.
How do you remove a stuck trip lever tub drain stopper?
Try spraying some WD-40 down the overflow drain pipe where the plunger sits. The lubrication may help to loosen the stuck plunger tip from the walls of the overflow tube. Use pliers to grip the rod and attempt to lift straight up on the plunger. DO NOT pull at an angle.
How do you unclog a trip lever drain?
1). Slowly withdraw the trip waste mechanism and plug from the overflow pipe. Clear hair from the mechanism and run hot water down the train to flush away any debris. Then, open the trip lever on the cover plate, and feed the lever and plug back into the overflow pipe.
How do you remove a push pull drain stopper?
0:502:25So Easy! How to Remove a WATCO Pop-up Drain Plug - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo pop it up into the up position. And then I can't really get down in there to show you but theMoreSo pop it up into the up position. And then I can't really get down in there to show you but the shaft the collar that this sits on. Actually is flat on two sides. So that a 9/16 wrench. If you sit
How to lower a stopper on a tub?
To lower the stopper, thread the bottom lock nut down. Next, spin the adaptor that the plunger hangs from down until it reaches the bottom lock nut, and then tighten the upper locknut to the adaptor. Place the plunger, threaded rod, and trip lever back into the hole in the tub and screw the plate back into place.
How to keep water in tub when it drains out?
Close the stopper, run some water into the tub, and see if it stays. If the water drains out, repeat the process above and lower the plunger a little bit more until you get the bathwater to stay in.
What is a tub drain?
Bathtub drains consist of a visible trip lever, a plunger that seats in the drain to stop water, and two pieces of threaded rod which connect the lever and plunger. The assemblies are adjustable to fit a wide range of tubs. The first step is to unscrew the plate that holds the trip lever.
How long does it take for a bathtub to drain?
10 to 20 minutes. Bathtub drain assemblies are mysterious things. Somehow, a lever placed well above the bottom of the tub controls whether the water stays in the tub when it’s wanted, and then allows it to drain when bath time is over. When a tub won’t hold water, the two potential causes are easily repaired.
Who is the master plumber of the old house?
In this video, This Old House master plumber Richard Trethewey shows how bathtub drains work, and how to fix them when they don’t.
What does it mean when a bathtub drain stopper doesn't work?
Any bathtub drain stopper that doesn't do its job is an annoying inconvenience. Usually, the problem is easy to fix, though the procedures vary depending on what type of tub stopper you have. Some drains have stoppers that are spring-loaded, operated by a push of the toe or by hand, while others use a trip-lever mounted on ...
How does a trip lever drain work?
Rather than a lift-bucket plunger that seals a drain opening at the bottom of the overflow tube, there is a spring at the end of the connecting rod. This spring pushes down on a pivot arm that levers the pop-up stopper up into an open position when the trip lever is moved. When the trip lever is moved to the closed position , gravity allows the stopper to drop back down and seal the drain opening.
Where is the lift bucket on a bathtub?
The small up-and-down lever you see protruding from the overflow plate on your bathtub is connected to a vertical connecting rod inside the overflow pipe behind the front tub wall. Near the bottom of the connecting rod is a plunger of some kind—usually a weight that works by sealing the drain opening at the bottom of the overflow tube. This type of drain stopper is sometimes known as a lift bucket.