
Here’s a simplified explanation of the process of replacing a VOG board mobile home wall panel: Use your fist (or a rubber mallet) to strike the panel until you find the studs. This will also help loosen the glue and batten strips on the panel.
How do you replace a vog board mobile home wall panel?
Here’s a simplified explanation of the process of replacing a VOG board mobile home wall panel: Use your fist (or a rubber mallet) to strike the panel until you find the studs. This will also help loosen the glue and batten strips on the panel.
What are vog wall panels?
Manufactured homes usually use VOG (vinyl-on-gypsum) wall panels rather than standard drywall. These vinyl-coated walls have a shiny finish, and there is often a printed design layer that is applied over the gypsum and under the shiny vinyl topcoat. Manufacturers favor VOG panels because they are lightweight and easy to install in factory settings.
How do you paint vog panel walls?
Just like any other wall in a home, priming the surface is the first step. Priming a clean surface will ensure that your paint color is well bonded to the VOG panel walls. Again, you have one of three options when choosing a primer: oil-based, acrylic or a two-in-one primer and paint base.
Can you remove battens from vog walls?
If you choose to remove the battens, you will need to tape and mud your walls with a drywall joint compound. VOG panels do not have the tapered edges found on drywall panels, so it's a bit harder to get a seamless finish but still possible.

How do you repair a VOG wall?
Manufactured Home Wall Repair PatchStep 1 - Sand lightly around damaged area of wall.Step 2 - Apply spackling compound to back of match.Step 3 - Place patch over damaged area.Step 4 - Spread compound over patch, then let dry.Step 5 - Sand, then apply texture or paint for desired appearance.
How do you repair plastic wall panels?
One way to overcome this is to cut a full-depth repair patch. Use the patch as a template to mark around the damaged area with a soft pencil. Cut out the damaged area carefully and sink the patch into the gap to the same depth as the panel surface. Use colour-matched silicone to stick and seal the patch in one go.
How do you fix damaged paneling?
STEPS | Wood Paneling Wall RepairGather materials and tools.Place brace and secure to wall.Cut patch material and secure to brace.Add filler material.Allow filler material to dry, then sand wall repair flat.Clean sanded repair and apply finish.
Can you paint over VOG panels?
The vinyl surface of VOG panels will accept paint better if you first coat them with a good quality acrylic primer. Applying primer is done like any painting job. Start by using an angled trim brush to cut in the primer along the edges of the wall, then apply the primer to the broad areas using a roller.
How do I fix my bathroom cladding panels?
0:062:44How to fit bathroom cladding - YouTubeYouTubeStart of suggested clipEnd of suggested clipSystem each panel simply slots into the last one fitted depending on what surface you are fitting toMoreSystem each panel simply slots into the last one fitted depending on what surface you are fitting to you can silicone glue staple screw or nail your cladding.
How do you repair laminated wall panels?
0:402:53The EASY Way To Fit Bathroom Wall Panels - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd ensure you push it in your internal trim. Use your drill to fix the counter some screws into theMoreAnd ensure you push it in your internal trim. Use your drill to fix the counter some screws into the tongue of the panel. Harry this process out for the rest of your panels.
How do you fix peeling paneling?
When you have peeling wood paneling, you can repair it with epoxy wood filler.Examine the delaminated wood paneling carefully to identify the outer edges of the delamination. ... Pull the damaged section away from the wall. ... Scrape away any glue that remains in the open area, using a putty knife.More items...
How do you fill holes in paneling?
Use a putty knife and apply spackling or caulk to fill nail holes. Scrape off any excess. Allow to dry until hard. Tip: If your paneling has groove lines, fill these in using a caulk gun for a smoother painted surface.
Can you spackle paneling?
Your wood panels may have visible cracks that need to be covered to form a uniform surface. Therefore, using the putty knife, apply the joint compound or the spackle to cover the grooves. Use the putty knife and press the spackle firmly into the cracks to have a smooth surface.
What kind of paint do you use on Vog?
One manufactured homeowner and blogger named Tracy recommended an acrylic Sherwin-Williams paint based on her own VOG wall board painting experience. If your VOG walls are more glossy, an oil-based primer may work better. We suggest using oil primer and oil paint.
How can I make my mobile home walls look better?
WallsRemove all trim from the walls.Prime the walls with an oil based primer.Fill in the line gaps in the paneling with drywall mud.Tape and mud the joints between the 4 x 8 sheet of paneling.Spray orange peel texture on the walls.Prime the walls for paint with a latex primer.Paint the walls.
Can you wallpaper over VOG panels?
You'll still want to primer the wall and the seam between the VOG panels. Tape and mud as you would sheetrock. Lastly, you will need to lightly sand the compound to create an even surface. Paint, texturize, or wallpaper for a finished look.
Can you patch wall paneling?
If your wall paneling has a hole or gouge, don't despair; a repair is not as difficult as you think. In most cases, a simple patch can make the paneling look new.
How do you fill holes in paneling?
0:222:51How To Patch or Fill Holes On Uneven Surfaces Like Wall PanellingYouTubeStart of suggested clipEnd of suggested clipSo the first thing you want to do is obviously get some fill it in there. Now you need to fill itMoreSo the first thing you want to do is obviously get some fill it in there. Now you need to fill it twice. When you fill it make sure you push the fill up in on the edges. So it sticks to all the edges.
What are PVC wall panels?
PVC wall and ceiling panels are made of a waterproof material which makes these panels highly resistant to water. The PVC panels are best suited for cladding the ceilings and walls of moisture-laden areas – for instance, bathrooms, basements, garages – which are prone to dampness.
How do you fill strips in mobile home walls?
7:108:26NEVER Do this to your Mobile Home Wall Strips, or Batten ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipAfter you pull all the batten strips off or pull those batten strips off drive all the staples. FillMoreAfter you pull all the batten strips off or pull those batten strips off drive all the staples. Fill it fill the big gaps tape and finish it but you need to use hot mud on a deeper fill.
What are wall panels made of?
The wall panels of a manufactured home can be made from several different material types, including drywall, porcelain tile, artificial wood and many others. The most common wall panel material in today’s manufactured homes is vinyl on gypsum, or VOG board. VOG panels are a widely used and cost-effective building material used in manufactured ...
How to get replacement wall panels?
To get a replacement wall panel that matches your home’s current panels, contact the manufacturer of your home. The manufacturer will be able either to provide you with a replacement panel from the same series or the closest available equivalent. Keep the serial number of your home handy during this process so that the manufacturer can track your ...
Can gypsum board crack?
The gypsum board in VOG panels stands up to everyday bumps well enough, but heavier impacts can cause the boards to crack. Other wall panel types can also suffer damage, too, so any manufactured home owner should have some basic knowledge of the procedures for replacing a mobile home wall panel.
Where is the serial number on a manufactured home?
The serial number is located on your manufactured home data plate, which you’ll typically find inside a cabinet, closet or utility area somewhere in your home.
Is it a good idea to hire a professional for manufactured home repairs?
It’s never a bad idea to hire a professional for manufactured home repairs, but many homeowners choose to go the DIY route, as it can be a substantial money saver. However, not all manufactured home repairs are DIY-friendly, so it’s important to know which ones should be left to the pros. Fortunately, replacing a wall panel is one ...
Can you replace wall paneling?
Fortunately, replacing a wall panel is one of the easier manufactured home repairs to DIY. The process is relatively simple, and the tools and materials are readily available from any hardware store. (Note, however, that some types of wall paneling, such as porcelain tile, are more difficult to replace than others.)
Why do people use VOG panels in their mobile home?
VOG panels are used because they are lightweight, water resistance, easy install, clean, and maintain. Below you can see low-gloss vinyl wallboards used in a manufactured home bathroom: Image Source: ths.gardenweb.com.
What is batten in a vg?
Battens are used to cover the seam where two VOG wall panels meet. By installing battens the factory is able to build homes faster and cheaper. Unlike drywall or sheetrock, VOG panels do not require taping and mudding so the edges of the panels are not tapered and the installation process is much faster.
What paint should I use for a VOG?
CDS, a large VOG manufacturer, recommends an oil primer with two coats of alkyd or latex semi-gloss enamel paint: Two coats of alkyd or latex semi-gloss enamel. Oil primer with a finish coat of oil paint or flat latex.
What is a VOG panel?
Vinyl on gypsum (VOG) panels has a laminated-like coating that holds the gy psum together. It’s used in mobile homes because it repels water, ...
How thick is gypsum?
Gypsum is calcium sulfate dihydrate, a soft and lightweight white or gray chalk-like mineral. Vinyl on gypsum panels is typically 5/16″ thick with a glossy paper coating. They do not have tapered edges so installers use battens, or strips, to cover the seams where two panels meet.
Can you paint wallpaper with caulk?
Paintable wallpaper is easy to hang but it needs to be thick enough to withstand the wet paint and keep the paper from showing the gap made by removing the battens. Of course, you can always fill the seam in with caulk or drywall compound ( see below ). Image Source: MyMobileHomeMakeover.com.
Can you paint over battens?
Once the battens are removed you can paint, texture, or wallpaper over the walls. Removing the battens is the easy part, filling in the gaps that the battens were covering, and then making the entire wall look cohesive is the difficult part. Related: Removing Walls in a Mobile Home.
What is a VOG panel made of?
First, let’s review some key information about VOG panels. They’re made from sheets of vinyl applied to thin panels of gypsum board (commonly known as drywall). The vinyl sheets sometimes have wallpaper-like patterns printed on them.
How to get full coverage on walls?
Use gentle strokes with the roller to avoid damaging the walls. Grab your angle brush and use the technique of “cutting in edges” to get complete coverage in the nooks and crannies. Finally, remove the painter’s tape, give your walls some time to dry and you’re done!
Can you sand a vog wall?
VOG walls can be damaged just like drywall, so use extra care at all points during the painting process and don’t sand your walls if possible. Typically, the seams of VOG panels will be covered by plastic strips called battens. It’s up to you whether or not to remove the battens.
Can you remove battens from a paint job?
Removing the Battens. A more even paint job is the biggest point in favor of removing your battens. Some homeowners also simply don’t like the way that battens look. However, removing battens can be time-consuming and requires the homeowner to tape and patch the wall seams with drywall compound.
What is VOG wall?
Manufactured homes usually use vinyl-on-gypsum (VOG) wall panels rather than standard drywall. These vinyl-coated walls have a shiny finish, and there is often a printed design layer that is applied over the gypsum and under the shiny vinyl topcoat. Manufacturers favor VOG panels because they are lightweight and easy to install in factory settings.
How to smooth a wet joint?
Cover the wet compound with strips of joint tape and press it into place with a 4-inch drywall knife. Immediately cover over the tape with another layer of joint compound, applied with the 6-inch knife. Let the taping compound fully dry. Lightly sand the joint to smooth.
What is the most popular home improvement project?
By far the most popular of all home improvement projects is painting the walls. New paint color can instantly change the entire look of your home, and just about anyone can successfully paint walls. But while painting is a very easy project with standard "stick-built" home construction, where the walls are finished with standard gypsum wallboard, it is a little trickier if you live in a mobile home or manufactured modular home, where the walls are made from different material.
How to get paint to bond with paint?
The surface you are going to paint must be clean to ensure a good bond with the paint. Start by covering the floors and furniture with drop cloths. Then, clean the walls with a mild detergent or TSP solution and rag. Go over each surface twice, then finish by wiping down with a fresh cloth dampened with clear water.
What to use to mask edges of walls?
Once the walls have dried, use painter's tape to mask the edges along with the trim, ceiling, and floor. If the walls have any kind of damage or holes from nails or screws, fill them with spackle, then sand smooth, following manufacturers' directions.
Can you tape battens on a manufactured home?
If you choose to remove the battens, you will need to tape and mud your walls with a drywall joint compound. VOG panels do not have the tapered edges found on drywall panels, so it's a bit harder to get a seamless finish but still possible. Taping is the best option if you are texturing your manufactured home walls or if you prefer a smooth finish.
Can you paint a vog panel?
Although the way VOG panels are manufactured and installed does complicate the job, it doesn't mean you can't paint ...
What is the difference between a VOG and a drywall?
From a glance, VOG can resemble finished drywall, and the biggest and most noticeable difference is the batten strips that connect the two panels together at the seam. A large majority of manufactured homes use VOG panels for their walls, and with good reason.
How do I paint vinyl walls?
The wall board manufacturer CDS also suggests the best way to paint vinyl walls is by using oil primer and oil paint. Expert Tip: Testing Your Primer: After you clean your wall board, apply a 3"X3" sample of primer on your wall. Let it stand 24 hours. Then put masking tape on the primed area and press down firmly.
How many layers of paint should I use for vinyl walls?
Most professional painters recommend doing two thin layers of paint rather than one super thick layer because it yields the best results.
What is a smooth paper wrapped wall?
If you're wondering whether you have paper covered sheetrock or vinyl covered sheetrock, evaluate your wall by feeling it! A smooth wall board means it is paper wrapped and a textured wall board means it is vinyl covered.
What is smooth wall board?
A smooth wall board means it is paper wrapped and a textured wall board means it is vinyl covered. You can also ask your friendly home consultant for help determining the difference. 5. Add The First Coat. Just like any other wall in a home, priming the surface is the first step.
Can you remove batten strips and fill in seams?
Following your room prep, you need to determine if you want to remove the batten stripsand fill in the seams, which can be quite difficult, or if you'd rather leave the strips where they are and paint over them.
Is gypsum drywall only for manufactured homes?
Most people think drywall is the only option, but Clayton Built® homeowners know otherwise. Other than finished drywall, gypsum panels are a popular option for manufactured and modular homes!
