- Do some research to find a good replacement/upgrade blade for your clipper
- Unscrew and remove your current blades
- Clean the clipper to remove any hair clipping or grease accumulation
- Place your new blades on the clipper and screw them loosely
- Align your blades and hold them in place using your other hand
- Gently, tighten the clipper’s screws simultaneously to maintain blade alignment
- Oil your new blades
- Switch on the clipper to distribute the oil and confirm that the blades are in place as expected
Full Answer
How to fix Wahl Clippers won’t turn off issue?
Steps to repair Wahl clippers won’t turn OFF issue Remove back cover of clipper – unscrew 3 screws of back cover There are two screws that are holding the power switch – You need to remove them (make sure your clipper is disconnected from power source)
How do I take apart and sharpen my Wahl Clipper?
The guide will teach you how to take apart, sharpen, and reassemble a Wahl hair clipper. It is recommended to clean and sharpen your clipper every 3 or 4 uses. No parts specified. Take your Philips head screwdriver and loosen the set screws by turning them left. This will allow you to separate the blades from your clipper.
How to clean the blades of a Wahl 1045 precision Clipper?
1 Unclip the tips and remove 2 Unscrew the top 2 screws to remove blades 3 Clean the blades using small brush / alternatively blades can be jam due to bending, in such case you can replace blades using Wahl 1045 Precision Clipper Blade Set 4 Apply some oil to blades 5 screw back again
How long does it take to fix Wahl Clippers?
Since Wahl strives to maintain high standard for its products, urging that anything from a bad battery to a loose motor be brought in for service, the company has several service centers located throughout the US. Depending on how close you are to one of these centers, your clippers may be fixed in as little as 48 hours.
How do I fix my Wahl Clippers not cutting?
Why Won't My Blades Cut?Remove the blade from the clipper.Use a small cleaning brush to get any loose hair that may have accumulated between the blade and clipper. You may also use a pipe cleaner or index card to clean between the teeth of the blade. Next, you should oil your blade regularly.
How do I rebuild my Wahl Clippers?
0:168:21How to Reassemble Wahl Clippers - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou're just going to put the padding back on here behind this piece this has a little knob. RightMoreYou're just going to put the padding back on here behind this piece this has a little knob. Right here that you're gonna put on there. And then you're just going to pop it shut.
Why is my Wahl Clipper not working?
If your electric Wahl Razor will not turn on, one problem could be the batter needs to be changed. In order to do this, the back must be unclipped and taken off. The battery is then attached in between two prongs. The battery is then removed and replaced with a Battery Set, 2 "AA" Ni-Cad 2.4.
How do you take Wahl Clippers apart?
0:123:58How to clean Wahl clippers - YouTubeYouTubeStart of suggested clipEnd of suggested clipAll you'll need for this is just the your larger end and smaller end screwdriver and some kind ofMoreAll you'll need for this is just the your larger end and smaller end screwdriver and some kind of brush to clean it out with.
Can hair clippers be repaired?
The cutting blades can become clogged and the cutting edges can be damaged. Fortunately, you can make many repairs yourself. Some new models actually clean themselves. Remove the fasteners holding the two halves of the case in place to expose the motor and switch.
How do I fix my Wahl Clipper spring?
0:296:09How To repair Your Electronic Hair Clippers Spring AttachmentYouTubeStart of suggested clipEnd of suggested clipYou can also use a paperclip. And bend the paperclip to fit the shape of this start with the square.MoreYou can also use a paperclip. And bend the paperclip to fit the shape of this start with the square. Then add a couple loops it'll probably be I think it was tubes for the paperclip.
Why did my clippers stopped cutting?
If you can stop the cutting blade with very little pressure, then your power is too weak, and you will need to clean out your tool and/or adjust the power (upcoming article). If all the teeth are present and your power is good, then you will need to clean your blades.
How do I take apart my Wahl Senior Clippers?
12:0021:25How to Deep Clean Wahl Seniors... - YouTubeYouTubeStart of suggested clipEnd of suggested clipOkay so once you have this cleaned off now with your connectors facing up we are going to place thisMoreOkay so once you have this cleaned off now with your connectors facing up we are going to place this back in here get our screws.
How do you put clipper blades back together?
1:335:57How to Put a Clipper Blade Back Together Quickly - YouTubeYouTubeStart of suggested clipEnd of suggested clipDo a couple of drops of oil on the back rail. And then i'll do one drop sorry that was two on theMoreDo a couple of drops of oil on the back rail. And then i'll do one drop sorry that was two on the cutter. I then stack the cutter. And i take the back.
How do you fix hair clippers?
1:452:41Blades are NOT moving HOW TO Fix a broken Hair clipper Wahl Conair ...YouTubeStart of suggested clipEnd of suggested clipNow. So my Conair Hair Clipper wasn't working what I've done is I've just taken it apart I'veMoreNow. So my Conair Hair Clipper wasn't working what I've done is I've just taken it apart I've cleaned it out i check the blades the blades were actually I don't know if just with gunk in there and
How do you put clipper blades back together?
1:335:57How to Put a Clipper Blade Back Together Quickly - YouTubeYouTubeStart of suggested clipEnd of suggested clipDo a couple of drops of oil on the back rail. And then i'll do one drop sorry that was two on theMoreDo a couple of drops of oil on the back rail. And then i'll do one drop sorry that was two on the cutter. I then stack the cutter. And i take the back.
How do you put a Wahl nose trimmer back together?
5:588:22Wahl Micro Groomsman assembly - YouTubeYouTubeStart of suggested clipEnd of suggested clipAll you're going to do is take the outer portion here there's two male pins there's one on this sideMoreAll you're going to do is take the outer portion here there's two male pins there's one on this side and there's another one on that. Side. You want to start one side or the other.
How do you put the blades back on a Wahl dog clipper?
0:592:15Change Blade of Wahl KM 2 Dog Groomer - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you push the button up as far as it will go you pull the head back and you pull it off see you'llMoreSo you push the button up as far as it will go you pull the head back and you pull it off see you'll notice there's a lot of hair a metal brush.
How do you sharpen Wahl Clippers?
0:000:30How to Sharpen Hair Clippers - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo sharpen hair clippers remove the blade from the clippers. And run it along a 4 000 grit coarseMoreTo sharpen hair clippers remove the blade from the clippers. And run it along a 4 000 grit coarse honing stone which you can get at a home improvement. Or hardware store angle the blade.
How long does it take for wahl clippers to fix?
Since Wahl strives to maintain high standard for its products, urging that anything from a bad battery to a loose motor be brought in for service, the company has several service centers located throughout the US. Depending on how close you are to one of these centers, your clippers may be fixed in as little as 48 hours. Clippers which are beyond fixing may be replaced by the company.
Where to take clippers for repairs?
Mail or take the clippers to the service center for repairs.
Does Wahl have a service center?
Since Wahl strives to maintain high standard for its products, urging that anything from a bad battery to a loose motor be brought in for service, the company has several service centers located throughout the US.
General Repairs
If your Wahl tools need repair services, you've come to the right place. Whether your home grooming tools or professional grooming tools need to be fixed, contact us with your repair needs and we can help you.
Blade Repairs
Do you have Wahl clippers, trimmers, or shavers need a blade repaired? Whether you need blades fixed on your home grooming tools or professional grooming tools, contact us with your repair needs and we can help you.
Service Terms
Seller, Wahl Clipper Corporation, upon acceptance of an order placed by Buyer, will supply the products and services specified in the order pursuant to and expressly limited by of all the terms and conditions stated herein.
FAQs
Do you have questions? We have answers. Search below or choose a category to see what others have asked.
WATCH TUTORIAL VIDEOS
Watch our tutorials and how-to videos on hair and grooming trends. We have tutorials on personal care, hair trends, tips for pet grooming and more.
How to separate blades from Philips clipper?
Take your Philips head screwdriver and loosen the set screws by turning them left. This will allow you to separate the blades from your clipper.
How to tighten Philips blades?
Place your blades back into position and insert your set screws into the proper holes. Take your Philips screwdriver and turn the screws to the right until you feel them completely tighten. Be careful to line up your blades correctly.
How to sharpen a whetstone?
Run your blade left and right in a horizontal direction across a Whetstone honing stone. First on the coarse side to sharpen the blade then on the finishing side to smooth out the blade.
How to use Wahl clipper oil?
The blades of your new clipper should be oiled every few haircuts. Simply place a few drops of Wahl Clipper Oil on the teeth of the blades. Use only the Wahl Clipper Oil included in the pack. Due to the high speed of your Wahl clipper, the correct type of oil must be used. Do not use hair oil, grease or any oil mixed with kerosene or any solvent, as the solvent will evaporate and leave the thick oil, slowing down the blades. Wahl Clipper Oil is a very thin, natural oil which will not evaporate and will not slow down the blades.
How to attach guide combs to clippers?
NOTE: To attach guide combs, hold comb with the teeth up. Snap guide comb attachment firmly to the bottom of the clipper blade. (L)
How to do a sideburn on a clipper?
(On a multi-cut clipper, push the taper lever up to the “close-cut” position.) Comb hair into desired style. Starting between the ear and the sideburns, as shown at left, hold clipper with corner edge of blade against the hairline. Slowly follow the desired outline of the hair over, around and behind the ears. For defining side-burns and the back of the neck, hold the clipper upside down, against the skin at the desired length and move down. Comb hair and check that sides are even. Check for uneven spots throughout the haircut.
How to cut uniform hair?
For uniform cutting, allow the clipper to cut its way through the hair. Do not force it through at a faster rate.
How far back should a clipper blade be from the bottom?
End of top blade teeth should be approximately 1/32 ″ (.64 mm) back from bottom blade. This is important so that the clipper does not cut too close or allow the moving cutter to touch the skin.
Do Wahl clippers need to be aligned?
Your Wahl clipper blades were oiled and aligned before leaving our factory; however, it is possible for blades to get bumped out of alignment. Blades must be realigned if they have been removed for cleaning or replacement. To determine if realignment is necessary, compare your clipper blades with diagram G.
Do all Wahl guide combs come with a kit?
Some kits do not include all Wahl guide combs. However, any of these combs (or additional accessories not listed here) may be available from your dealer or can be ordered directly from Wahl.
