The furniture veneer may buckle or warp as a result of contact with water. To repair the damage, you can soak the veneer with a moisturizer until it lies down flat again. Wipe it dry and clean. Fill a syringe with veneer glue and stick the needle between the veneer and the body of the furniture.
Full Answer
How to save your laminate floors from water damage?
How to Fix a Laminate Floor That Got Wet?
- Contain the Damage. Obviously, if your laminate is still being exposed to water then there’s no point in going through the process of fixing it.
- Check the Locking System to Find Damage. ...
- Make Sure You Have the Proper Tools. ...
- Remove the Laminate Up to the Damaged Area. ...
- Replace the Damaged Planks. ...
- Reinstall the Laminate. ...
How do I repair water damage to a laminate floor?
- Depending on how wet the flooring got, you may want to use more than one of each.
- Position them in such a way that the fans are angled downward, and blowing directly onto the floor.
- Set up dehumidifiers, and position them strategically around the affected area.
How to paint laminate after water damage?
- Shake up a small can of stain or furniture polish.
- Dip your old rag into the stain or polish.
- Rub the covered rag over the scratches, coating them with stain.
- Wipe them off with the dry part of the rag, and the laminate scratches will have disappeared.
- Plug your iron in and turn it on to medium heat.
How to clean laminate wood floors without doing damage?
- The best way to clean laminate floors is to use products made especially for them. ...
- Use a damp mop on your floors every two to three months. ...
- You can also use a laminate floor mop. ...
- After mopping, go over floors with a dry microfiber cloth or a dry mop to make sure there’s no water left on the floor.

How do you repair water-damaged laminate furniture?
If the glue just won't come off, squeeze hot water from a sponge under the loose piece of veneer. The water will eventually melt the glue so you can then remove it using the knife. Wipe off any excess moisture. Re-attach the veneer by adding fresh white (wood) glue, then put a piece of plastic over the repaired area.
How do you refinish water-damaged veneer?
To repair a veneer blister, carefully slit it open with a razor knife. Then use a glue syringe or a toothpick to apply yellow carpenter's glue beneath the veneer. Press down lightly on the blister to spread the glue. Cover the repair with wax paper and a flat wood block, then clamp the blister flat.
How do you paint bubbled laminate furniture?
3:404:57How To Remove Bubbles on Laminate Furniture - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you can use your bin or whatever you want to do but i would definitely recommend priming beforeMoreAnd you can use your bin or whatever you want to do but i would definitely recommend priming before you paint. So i did two coats of the primer. And now i'm going into the paint.
Can wet particle board be repaired?
Accidents happen, and sometimes the particle board may experience water damage. When this happens, the surface will swell up and lose its smooth shape. Thankfully, water damaged particle board isn't too difficult to repair. In some cases, there may be enough damage that requires new sheets of material.
How do you fix a swollen laminate table top?
Simply dip a clean fiber-free cloth in the mineral oil and rub it on the wood to apply an oil finish. You can also apply an extra polish of mineral oil after it dries.
How do you fix a water-damaged dining room table?
Undo water damage. Start by placing a clean, thick towel on top of the stain. With your iron on a dry low-to-medium setting, press over the towel (making sure the soleplate doesn't touch the wood) for several seconds. The gentle heat will warm the finish enough to release the moisture into the towel.
How can I tell if my furniture is laminate or veneer?
1:354:46How to tell the difference between laminate and veneer ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo first and foremost the wood grain it's a pattern. So that's usually a good sign that it is aMoreSo first and foremost the wood grain it's a pattern. So that's usually a good sign that it is a laminate. But do you see how it kind of chips back here. And you can't really see the wood grain.
What kind of paint do you use on laminate furniture?
Latex paintLatex paint is recommended for laminate surface painting projects because of its durability and smooth finish. Try ProClassic Interior Acrylic Latex Enamel for lighter colors, and All Surface Latex Enamel Base for deeper hues.
How do you refurbish laminate furniture?
0:502:52How to Paint Laminate Furniture | Benjamin Moore - YouTubeYouTubeStart of suggested clipEnd of suggested clipCompletely using advanced interior paint or insulux cabinet coat apply an even coat of paint. AndMoreCompletely using advanced interior paint or insulux cabinet coat apply an even coat of paint. And let it dry. Completely before applying a second coat.
How do you fix a water-damaged particle board dresser?
To fix particleboard furniture with water-damage, first dry off the water. Then use sandpaper to buff the swollen areas. You can use a sharp knife to remove severely water-damaged swollen areas. Replace these holes with wood filler.
How do you repair laminate particle board?
0:179:31Particle Board Furniture Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd creates a strong bond between the flextech in the wood mix. Two parts a with one part B andMoreAnd creates a strong bond between the flextech in the wood mix. Two parts a with one part B and apply it to the repair area using a brush. The next step is to dispense and mix the flextec.
How do you fix the bottom of a water-damaged cabinet?
1:128:55Rotted Sink Cabinet Floor--How To Fix - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is specifically sand apply which is Home Depot's brand of plywood it's cheap it's almostMoreThis is specifically sand apply which is Home Depot's brand of plywood it's cheap it's almost cabinet great it looks good when it's painted.
How do you get paint to stick to laminate?
0:526:26HOW TO PAINT LAMINATE FURNITURE *no sanding* - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo far i like to use this primer which is a shellac based primer shellac base primer not water-basedMoreSo far i like to use this primer which is a shellac based primer shellac base primer not water-based. It's going to enable. Your paint to stick to your laminate surface.
Can you paint laminate furniture without sanding it?
So yes! You can paint laminate furniture without sanding! Keep in mind though, if you have any scratches or spots of nail polish (like I did), you'll want to sand those areas so you have a nice smooth surface for your paint.
What primer should I use on laminate furniture?
INSL-X STIX Waterborne Bonding Primer is one of the best primers for laminate furniture. This primer is made specifically to bond to surfaces that are hard to coat, and will give you a smooth, level finish.
How do you smooth textured laminate?
Countertop paint should work fine on textured laminate, though the texture will tend to show through. You may be able to remove some or all of the textured look by applying several coats of countertop primer or paint, sanding lightly with fine sandpaper between each coat to fill in the textured surface.
What is wood laminate furniture?
Wooden furniture generally comes in two types--natural or laminated. A laminated piece of furniture uses a very thin covering of a different type of wood or particle board that is stained or finished to look like a more expensive or exotic type of wood. While these coverings are very durable and can ...
How long does it take for a rag to dry?
Wipe away any excess with your old rag and allow to dry overnight.
How to tell if laminate is water damaged?
Look for warped areas that are bending or cracking. When laminate gets saturated by water, it absorbs the moisture which in turn breaks down the structure of the flooring. There are a number of signs that point to your floor being water damaged, including bending or cracking.
Why wipe laminate flooring?
Whenever there is a small spill of any kind on your laminate flooring, wipe it up immediately to prevent water damage from occurring over time.
Why is laminate flooring so popular?
Laminate flooring is popular among homeowners because it looks nice and is durable. These floors can last for years and don’t require much maintenance along the way. That said, the wood in the laminate floors is prone to water damage if it’s not treated properly.
What to do with sticky notes on floor?
Snap a picture of the entire floor with the sticky notes in case you need to show it to a flooring dealer.
What to do if you can't find planks?
If you can’t find any planks that look like the ones you have at home, you might be better off replacing the whole floor. Ask the flooring dealer for their advice if this is the case.
How to keep planks in place?
Place a heavy object on top of the planks to help them set. Be it a bookcase or couch, this object will keep the planks in one place and allow the adhesive to keep them connected for a long time.
Why do tiles pop out of the floor?
Tiles can also be pushed apart by water damage. Go over every tile individually when you check. As you walk around, push on your floorboards to see if they are popping up out of the base of the floor. Be critical when you do this, as even a small distortion to the tiles can be the result of water damage.
How to dry wood furniture after it has been soaked in water?
When a piece of wood furniture has been soaked in water, the very first thing to do is to let it dry. Place it in a room with warm temperature and good air circulation. You may want to turn on the heating and the fans. Alternatively, if the weather permits, you can leave the furniture to dry outside.
How to repair a warped veneer?
To repair the damage, you can soak the veneer with a moisturizer until it lies down flat again. Wipe it dry and clean. Fill a syringe with veneer glue and stick the needle between the veneer and the body of the furniture. Empty the syringe slowly. Remove it and place a wood block on top of the veneer. Wait for the glue to dry. Follow the manufacturer’s recommendations for the waiting period and remove the block.
Why is my furniture black?
Black spots on your furniture indicate that water has seeped through the finish into the wood, leading to the formation of mildew. In this case, you will have to remove the finish, clean the mildew with a bleach solution, and coat it with a new layer of finish.
How long does it take for a carpet to dry?
Remove and dispose of the padding, which you will have to replace in any event. Place the carpet in an elevated position and let it dry for 12 hours.
What to do if mold has formed on carpet?
If mold has formed, or if you feel the carpet needs to be disinfected, use the services of a cleaning company to finish the restoration process.
What happens if you put wood in a cold room?
Make sure the temperature is right. If it is too cold, the wood piece will dry too slowly and mold will form. If it is too hot, cracks will form in the furniture.
Can you clean water damaged carpet?
You can clean water-damaged carpets in one of two ways, depending on the condition of the water.
What Causes Wood Furniture to Bubble Up?
Swollen wood can easily detract from the beauty of your furniture, making it appear aged and scuffed. But understanding why your wood is swollen will help you maintain your wood furniture and save money in the long term.
How to Fix Water Damaged Swollen Wood Furniture
Here’s my first, no-kidding Sherlock, tip: clean up the water as soon as it gets on your wood furniture. You need to act swiftly — before the water is absorbed by the wood — to have the best shot at saving the wood. However, even if it’s too late, there’s still some hope for repairs to be made. Here are some possible methods.
Final Thoughts
Any water-damaged object or material, let alone wood furniture, is difficult to repair. You might need to make some hard choices on which pieces can be recovered and which pieces need to be discarded.
Call 1-Tom-Plumber
Don’t hesitate to contact us here or call us at 1-Tom-Plumber (1-866-758-6237) if you have leaking, flooding, or water damage issues you need to deal with immediately.
How to repair water damage on particle board?
To fix particleboard furniture with water-damage, first dry off the water. Then use sandpaper to buff the swollen areas. You can use a sharp knife to remove severely water-damaged swollen areas. Replace these holes with wood filler.
How to tell if particleboard is water damaged?
Tell-tale signs of water damage on particleboard is a swollen, bubbled-up surface in contrast to the previously smooth shape.
How to Seal Particle Board Edge?
There are products available in the market that help you seal the edges of the particleboard.
Why do particleboards swell?
Particleboards are commonly used for their durability and low weight. The boards also can be treated with waterproof sealants to help them resist water damage. Without that waterproof coat, particleboard can quickly swell up when it gets wet with water.
How to put particle board together?
Use veneer glue to put pieces of particle board together.
Why do you vacuum a board?
Vaccum the board to ensure that you have no powdery part left.
How to fix a leak in particleboard?
First, you will need to dry the wet particleboard. Use towels to quickly soak up the excess water. If possible, move the item to a dry area and fix any leaks. Since the natural drying process can take a long time, you will want to hasten this process to reduce the damage to the particleboard.
