- Disconnect the power to the washer.
- Disconnect the water hoses and move the washer to a suitable location.
- At the rear of the washer, locate three screws on the bottom of the control panel, and remove them.
- Tilt the control panel up and push it forward.
Full Answer
How do you reset a whirlpool Cabrio washing machine?
To reset a Whirlpool Cabrio, Press PAUSE/CANCEL on the display pad, select a cycle, and press “START”. Turn off the Whirlpool Cabrio when the error code appears, unplug it, and let it sit for 10 minutes. Plug the washer back in, select a cycle, and press “Start” to reset a Whirlpool Cabrio.
Are there any problems with Whirlpool Cabrio washing machines?
Whirlpool is a big name in appliances. One of the most popular models of their washing machines is the Cabrio. While this model has fewer problems than most, there are still some common fixes they require sometimes.
What to do if your Cabrio washer is not working?
For fuse boxes, replace any blown fuses. Unplugging the washer for up to five minutes can sometimes clear any problems the machine had or clear error codes. Cabrio washers use software and electronics to help you troubleshoot and fix simple problems with the machine by providing an error code on the digital display.
Why is my Cabrio washer filling up but not spinning?
If your Whirlpool Cabrio washer will fill with water but won’t spin, the lid lock switch is probably bad. To diagnose this problem you’ll want to put the washer in a spin mode. Next, open the lid and insert a screwdriver into the lid switch actuator hole.
What are the most common problems on a Whirlpool washing machine?
Here are seven of the most common problems on a Whirlpool washing machine and potential fixes for them.Washer Making Unusual Noises. ... Washer Won't Start. ... Washer Lid Won't Lock. ... LD Error Code Appears. ... Washer Leaves Deposits on Dark Clothes. ... Washer Has a Burned Plastic Odor. ... Rust Spots Appear on Washer Lid.
Why is my Whirlpool Cabrio washer not working?
The most common causes of a Whirlpool Cabrio not spinning are: Defective lid switch. Broken drive belt. Loose drive pulley nut.
How do you fix a Whirlpool Cabrio washer that won't spin?
1:183:39Whirpool Cabrio not Spinning FIX !!!(Actuator) - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you have to do is just lean it back anywhere um you go down here. And this is where the mainMoreSo you have to do is just lean it back anywhere um you go down here. And this is where the main water is. This is with the whole transmission. Drive shaft everything.
Does Whirlpool Cabrio washer have a belt?
Whirlpool Cabrio Washing Machines Most energy saving washers are front-loading and very mechanically complicated, however, this water saving washing machine operates without a transmission, motor coupling, belt, clutch or break assembly.
How long does a Whirlpool Cabrio washer last?
about 14 yearsTop loaders typically have a longer life than front load washing machines. This model should last about 14 years.
Is there a reset button on the Whirlpool Cabrio washer?
Try the Cabrio Reset Procedure Touch any button that you see on your display pad. This will clear the error code. Or you can press PAUSE/CANCEL. Choose a cycle and press START.
What would cause a Whirlpool washer to stop spinning?
If your Whirlpool washer Not Spinning well, you need to check the pump. It could be clogged with debris or defective and needs to be replaced. To check the pump, disconnect the drain line and remove the back panel of your machine. Check for debris with a flashlight, or check with a special tool.
How do I reset my Whirlpool Cabrio Top load washer?
Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.
How do you run diagnostics on a Cabrio washer?
3:048:04How to Put #Whirlpool #Cabrio #Washer into Diagnostic Test ModeYouTubeStart of suggested clipEnd of suggested clipSo i just press one two three. And and release one two three. And then until i get to the test modeMoreSo i just press one two three. And and release one two three. And then until i get to the test mode so you have to be very patient to be able to get on the test mode.
How do I know if my washer needs a new belt?
Diagnosing A Bad Belt Use a couple of bricks or small paint cans to prop up the front edge of the washer. This will allow you to easily see the belt, as well as its motor assembly. If your belt displays any signs of fraying, cracking, or burning, plan to replace it at once.
Where is the belt on a Whirlpool Cabrio washer?
0:232:10Whirlpool Top-Load Washer Won't Spin? Drive Belt #W10006384YouTubeStart of suggested clipEnd of suggested clipOut. Now use tape to secure the lid carefully tip the washer forward so the front of the cabinetMoreOut. Now use tape to secure the lid carefully tip the washer forward so the front of the cabinet rests on a blanket or towel. Now remove the screws securing the belt cover. And pull the cover off.
How do you run diagnostics on a Cabrio washer?
3:048:04How to Put #Whirlpool #Cabrio #Washer into Diagnostic Test ModeYouTubeStart of suggested clipEnd of suggested clipSo i just press one two three. And and release one two three. And then until i get to the test modeMoreSo i just press one two three. And and release one two three. And then until i get to the test mode so you have to be very patient to be able to get on the test mode.
Why will my Whirlpool washer not start?
0:121:41Washer Won't Start — Washing Machine Troubleshooting - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf the door lock switch is malfunctioning the washer may not start even with the door closed. It'sMoreIf the door lock switch is malfunctioning the washer may not start even with the door closed. It's also possible that the user control board has failed.
How do you bypass the lid switch on a Whirlpool Cabrio washer?
0:063:20Quick & Easy Whirlpool Washer Lid Switch Defeat - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe green wire can stay connected that's not going to hurt anything these wires don't matter if theyMoreThe green wire can stay connected that's not going to hurt anything these wires don't matter if they even short to the case which is painted. So it's not matter.
How do I put my Whirlpool washer in diagnostic mode?
0:000:48Whirlpool Washer Test/Diagnostic Mode - YouTubeYouTubeStart of suggested clipEnd of suggested clipLeft right right right left right once you do that all the dials on the board will start flashing.MoreLeft right right right left right once you do that all the dials on the board will start flashing. Turn your knob until it gets to the spin cycle once that happens press the start button.
How to take a break on a Cabrio washer?
When it’s time for your Cabrio washer to take a break, put the machine in standby mode. You can do this by plugging it in with all indicators off, or by turning on only the clothes clean or done indicator. Once the machine is ready to rest, choose any button except POWER, START, or STOP. Then follow the step-by-step instructions below.
What to do when Whirlpool Cabrio is whining?
The first step is to find a repair manual or diagram of the internal workings of the washer on the Whirlpool site.
Why is my washer not draining?
However, if it’s not working properly, your washing machine may not drain. A defective lid switch can keep the washer from functioning properly.
Why does my washer lid not fill?
When your washer lid unlocks, it could throw off the calibration, which may cause your machine to overfill or not fill enough. These problems can throw off the wash time and cycle, leaving you with a load of laundry that’s not as clean as you expected, or worse, another load of laundry to do after the first one.
What does it mean when a Cabrio washer doesn't spin?
If your washer does not spin or agitates, it means your drive belt is broken or loose on your Cabrio washer’s pulleys. Replacing this belt will restore functionality to your machine.
Why does my washing machine make a rumbling noise?
There are a number of reasons why this might occur. The washer can emit a rumbling sound while agitating while draining or spinning. Causes might include misalignment of the impeller, imbalance of load, or build-up of lint in the drain pump.
What is the purpose of a spin cycle in a washing machine?
The main function of the cycle is to take the laundry from being soapy and wet, and throw it around in a circle to get it clean. The Cabrio has an excellent spin cycle that can take even the most soaked items and get them clean and dry in no time.
Why does my Whirlpool Cabrio washer stop spinning?
The nut that holds the drive pulley in place can become loose over time. When this occurs it can cause your Whirlpool Cabrio washer to stop spinning. You’ll have to locate the drive pulley and tighten the nut.
Why won't my Whirlpool Cabrio spin?
If your Whirlpool Cabrio washer will fill with water but won’t spin, the lid lock switch is probably bad.
How to remove a washer motor?
If the nut on the direct drive motor becomes loose the OL error code can appear. To check this part, follow these steps: 1 Disconnect the power cord from the wall. 2 Turn off the water supply and disconnect water inlet hoses from the rear of the machine. 3 Pull the washer away from the wall to allow you room to work. 4 Loosen the screws on the access panel so you can remove it. 5 Locate the drive motor and belt. 6 Use an adjustable wrench to secure the motor’s mounting nut. Begin by turning it counterclockwise to loosen the nut. 7 Hold the motor in place firmly and tighten the motor nut by turning your wrench clockwise. 8 Keep one finger on the belt, when the belt can only be depressed about a half inch you have the right amount of tension. This may require 2 people. 9 Reassemble the machine, restore the power, and reconnect hoses.
What to do if your inlet valve is damaged?
If you find they’re damaged, replace them. Also, check the inlet valve itself to see if any debris has bypassed the screens and is present inside the valve . If so, clean out the two ports on the valve.
Why won't my Cabrio spin?
If your Cabrio won’t spin and is displaying error codes such as F7 or E1 you may have a shift actuator malfunction.
What is the most popular model of Whirlpool washing machine?
Whirlpool is a big name in appliances. One of the most popular models of their washing machines is the Cabrio. While this model has fewer problems than most, there are still some common fixes they require sometimes. Today we’ll take a look at all the common problems with Cabrio washers and the related fixes.
What happens if a washer doesn't run with the lid closed?
If the washer runs while you do this, but won’t run with the lid closed – the switch is bad. When you do this test and don’t get a result it may be necessary to check for continuity using a multimeter.
How does a Cabrio washer work?
Cabrio washers use software and electronics to help you troubleshoot and fix simple problems with the machine by providing an error code on the digital display . Some codes indicate issues you can resolve while others indicate the need for professional service:
What happens if you leave the lid open on a Cabrio washer?
When you leave the Cabrio's lid open for more than 10 minutes, water drains from the machine, and the washer resets. oL reports that you have overloaded the machine. Remove some of the items from the machine and restart the load. When the machine reports this error, it drains the water and detergent, requiring you to reset the load.
What does DU mean on a washer?
dU -- this code indicates the machine's lid won't unlock after completing a cycle. A basketful of laundry on top of the washer can cause this problem.
What does it mean when a Cabrio washer makes a clicking noise?
Clicking noises usually indicate items were left inside pockets and are now tumbling about inside the machine. When you wash tennis shoes or have an unbalanced load, it can create a thumping noise inside the washer.
Where to find Whirlpool model number?
You can find the appliance tag with the model number on the rear of the tub rim, underneath the lid.
Can you troubleshoot a Whirlpool Cabrio washer?
Instead of getting frustrated and overwhelmed when your Whirlpool Cabrio top-loading and high-efficiency washer has a problem, you may be able to troubleshoot the problem and fix it yourself without the costly help of a service technician. Basic power checks and the provided error code s help you narrow down the cause.
What to do if washer doesn't have enough water?
If the washer legitimately does not have enough water, the water inlet valve, water pressure, and water inlet hoses should be checked to find a solution to the issue.
What to do if washer stops mid cycle?
If the washer stops mid-cycle, the first thing to check is if a circuit breaker has been tripped or a fuse has blown.
Why is my washer not draining?
If the washer will not drain or it stops draining and displays an “LD” error code, it is usually because of a malfunctioning drain pump or blocked drain hose. The “LD” error code refers to “long drain” and occurs when the washer is taking too long to drain.
Why is my washer pump not working?
An issue with the pump may be caused by a foreign object or small item of clothing that has gotten through the washer’s filters and is restricting the pump. The drain pump’s impellers may also be damaged and restricting the pump. The drain pump can also fail electrically. A multimeter can be used to determine if the drain pump motor has continuity. The washer’s access panels will need to be removed to examine the pump.
Why does my washer squeak?
If these tips fail to reduce the noise issue, the washer likely has a worn-out shock absorber, suspension rod, dampening strap, spring, or tub bearing. If defective, these components will usually cause squeaking, thuds, and violent shaking. The washer cabinet will need to be removed to check and replace these parts.
Why won't my washer start?
If the washer will not start, checking for a tripped circuit breaker or a blown fuse is the most common solution to the issue.
How to stop a washer from shaking?
For the washer to function correctly and not excessively vibrate or shake, it needs to sit level on the floor. Using a leveling tool to check it is balanced and then adjusting the washer’s legs will often fix a noise (and performance) issue. To reduce noise (and stop water from leaking), the washing load also needs to be balanced in the tub.
