
How to Repair a Bubble in Wood Veneer
- 1.. For older furniture, cut a small slit in the bubble with the Exact-O knife in the direction of the grain.
- 2.. Heat the bubble area with a hair dryer or place several pieces of paper over the bubble and iron the paper over the...
- 3.. Roll over the bubble area immediately with the veneer roller or wallpaper seam-roller as soon as...
How to patch veneer with Quickwood?
Here s why:
- Dye colors are transparent, so they don t mask or muddy the wood s grain or figure.
- Dye imparts a uniform color to wood. Pigmented stain can collect in pores and scratches, giving a blotchy look or increasing grain contrast.
- Adjusting colors is easier with transparent dyes. ...
How to fix raised veneer?
How to Repair Bubbled or Blistered Wood Laminate Veneer
- Flatten the Bubble After steaming the laminate material to get it pliable, place a damp cloth over the bubbled (blistered) area. ...
- Add Glue Squeeze white (wood) glue into the slit, making sure to get the glue on both the underside of the veneer and the wood base. ...
- Clamp to Secure the Bond
How to repair Bubbling veneer?
Things You Will Need
- Hair dryer or clothing iron
- Several pieces of paper
- Exact-O knife
- Wood glue
- Waxed paper
- Heavy books
- Block of wood
- Veneer roller or wallpaper seam-roller
- Damp cloth
How to Repair Damaged veneer on a table top?
Repairing MDF or Veneer Based Wood Furniture
- Dry the Wood Completely. Set up a drying area that is well ventilated and not in front of direct heat or sunlight. ...
- Assess the Damage. Once your furniture is completely dry, inspect it to see if it can now be repaired. ...
- Remove Stains and Watermarks. ...
- Repairing Your Veneer Furniture. ...
- Choose a Finish and Apply. ...

Can bubbled veneer be repaired?
To repair a veneer blister, carefully slit it open with a razor knife. Then use a glue syringe or a toothpick to apply yellow carpenter's glue beneath the veneer. Press down lightly on the blister to spread the glue. Cover the repair with wax paper and a flat wood block, then clamp the blister flat.
What causes wood veneer to bubble?
A very thin layer of hardwood veneer is often glued over a less-expensive piece of wood furniture. Although veneer is usually durable, placing warm or damp objects on the veneer can cause the glue bond to fail. When the glue bond fails, bubbles can form on the surface of the wood veneer.
How do you fix bubbly wood?
Place a soft, clean cloth on the affected wood and iron it. Be careful not to burn yourself, the cloth, or scorch the wood by not pressing the iron down for too long. Another way to remove water bubbles is using a needle, wood glue, and wax paper to pierce bubbles and flatten the wood.
How do you get bubbles out of fake wood?
Minor bubbles can be fixed by “bursting” them. Place a damp cloth on the bubble and cut a slit on the bubbled area using a sharp knife. Squeeze wood glue into the slit you have opened and press the veneer down. Place a weight overnight so that it is entirely flattened.
Can you use wood filler on veneer?
You can easily fix your furniture with damaged or chipped veneer, yes YOU can! Here's how easy repairing veneer with wood filler can be! Get more tutorials on repairing old furniture here!
How do you fix water damaged veneers?
4:416:58Fixing Water Bubbled Damaged Veneer Vaneer on Wood FurnitureYouTubeStart of suggested clipEnd of suggested clipThere's a crack you can get glue get the thing pop it underneath there and squirt glue in there andMoreThere's a crack you can get glue get the thing pop it underneath there and squirt glue in there and then put the weight on it and it will take and wet and moisten that veneer.
Why does laminate form bubbles?
If the laminate is dry and the particleboard is wet, the laminate will bubble when the laminate grows and the substrate either shrinks or stays the same size. It takes laminate about two days to acclimate, if air can get to both sides of the material.
How do you get bubbles out of a laminate table top?
Bubbles in the MiddleLay a thin towel over the bubbles. Set an iron to low or medium heat. ... Roll over the bubbles with a rolling pin. Flatten the bubbles completely, and continue rolling until the laminate is cool to the touch.Place a paperweight or a few heavy books on top of the area.
How do you fix bubbles in laminate cabinets?
Heat the iron to medium-high, and place the folded towel over the bubbled area. Move the iron back and forth over the towel with firm pressure; this will heat up the glue beneath the laminate. Remember to keep it moving, because holding it still in one place can make the bubbling even worse.
How do you get bubbles out of wood furniture?
0:224:57How To Remove Bubbles on Laminate Furniture - YouTubeYouTubeStart of suggested clipEnd of suggested clipSome elmer's wood filler and you can use um like dixie bell mud or wood filler sanding black andMoreSome elmer's wood filler and you can use um like dixie bell mud or wood filler sanding black and then a rag. So i just take my razor blade. And i cut a square around the bubble.
How do you fix swollen wood?
One notable solution in fixing swollen wood furniture is by drying it thoroughly before anything else. You can remove the moisture by letting it sit under direct sunlight for at least 24 hours rather than using artificial means such as a hairdryer or blower.
How do you fix bubbles in laminate cabinets?
Heat the iron to medium-high, and place the folded towel over the bubbled area. Move the iron back and forth over the towel with firm pressure; this will heat up the glue beneath the laminate. Remember to keep it moving, because holding it still in one place can make the bubbling even worse.
How to fix bubbles in veneer?
Earlier in my career, I was trained to repair veneer bubbles by using an craft knife to slice the veneer in the center of the bubble, and follow that step by using a razor blade to slide glue under the veneer on both sides and then clamping. That method worked.....sometimes.
What glue do you use to repair bubbles?
The glue used can be either yellow wood glue, or hide glue. In this tutorial I used yellow wood glue, but hide glue is actually preferred because it can be activated by heat and softened. This allows us to continue our repair if for some reason the results are less than we had expected and perhaps part of the bubble is still present.
Can you heat up glue with an iron?
Another technique I personally never use, but know some do, is heating the surface with an iron in hopes of softening and reactivating the glue. My experience has been that the bubble is there for a reason, and while heat may seemingly work at fixing the bubble, it's typically temporary and the bubble will return sooner or later. However, if this bubble is on a piece you own, and not a clients applying heat with an iron could be worth a try.
Can veneer bubbles be repaired?
Repairing a bubble on a veneered surface can be one of the hardest fixes we come across on veneer furniture. Here's a tutorial demonstrating some techniques to make the job easier.
How to remove bubbled veneer?
Then break off and remove the bubbled up veneer. *See below for an extra tip. Mix up a small amount of Bondo and use the spreader or putty knife to fill in the hole.
What is bubbled veneer?
Bubbled veneer. When the wood veneer has lifted up in the middle of the table top, dresser top, or honestly, any big piece of wood that has veneer on it.
Where can I buy Bondo?
Bondo is available at a lot of hardware stores and comes in the quart of gallon size. Here is a link to Bondo on Home Depot. Please consider ordering it online for store pickup, to help out this little website of mine.
Why is my veneer jagged?
If the edges of the veneer don’t get filled completely smooth and seamless, it will look a lot more natural for the veneer edge to be jagged instead of straight.
Can old veneer be damaged?
Old veneer furniture is notorious for having damaged veneer. This dresser top had water damage, resulting in lifting veneer. If you have this problem, here’s how to repair bubbled veneer!
Does Bondo take wood stain?
Bondo will not take stain like wood does. Actually no wood filler actually takes stain like wood does.
Can you use gel stain on Bondo?
When the Bondo is set and dry, you can use different shades of gel stain to hide the repair.
How to get bubbles out of wood veneer?
Apply wood oil directly to the veneer to prevent new bubbles from forming. Rub the wood oil into the veneer with a cloth until the table is completely restored to its original condition.
How to get glue out of a veneer?
Press down on the veneer, to spread the glue underneath the bubble. Wipe away the excess glue from the veneer using a cloth dampened with water.
How to stop glue from sticking to wood?
Remove the masking tape from the veneer. Lay a sheet of plastic wrap over the split to prevent the glue from oozing out and sticking to the flat wood blocks you are about to place over the plastic wrap.
How to make bubbles in wood?
Step 1. Lay a sheet of white parchment paper over the wood bubble. Iron the parchment paper with a warm clothes iron for 10 seconds.
How to cover a split veneer?
Cover the wood bubble with two layers of masking tape , if the wood bubble remains. If the veneer has already split, place two layers of masking tape along both edges of the split.
Why does wood bubble?
Leaving warm or damp objects on wood can cause wood bubbles.
What happens when glue bond fails?
When the glue bond fails, bubbles can form on the surface of the wood veneer. Wood bubbles can ruin the appearance of a beautiful piece of furniture, causing the furniture to appear dull and dingy. Fortunately, these unsightly bubbles can be removed and a table can be restored. Advertisement.
How to keep epoxy from sticking to rubber?
Apply it and prop up or fasten the pieces so they stay in place while the epoxy cures. If needed, dampen the gloves with tap water to keep the epoxy from sticking to them as you press it in place.
What is epoxy putty?
Epoxy putty, which is also available from other brands, comes in a package that extrudes the basic epoxy and the required hardener in the proper proportions. To prepare the surfaces, polish them with steel wool or extra-fine sandpaper so that you see bright metal. Then open the package.
Can you use epoxy to reattach a handle?
Or you could probably reattach the handle using an epoxy designed for use with metal. One product is QuikSteel Copper-Reinforced Epoxy Putty ($10.35 at amazon.com ). The standard QuikSteel Steel-Reinforced Epoxy Putty ($5.99 at truevalue.com) would work equally well but would cure to a charcoal color rather than copper, said Clark Elmore, tech support manager for the Technical Chemical Co., which owns the QuikSteel brand. The type of metal reinforcing in the epoxy products is just a cosmetic issue, he said; the actual glue is the same.
