Repairing Guides

how to repair wooden shutters

by Jackson Stiedemann Published 3 years ago Updated 2 years ago
image

Repairing Exterior Wood Shutters

  • PATCH ROT. Chisel out rot and impact damage with an appropriate tool. Mix a small amount of two-part wood epoxy or even...
  • REPLACE DAMAGED AREAS. Remove any screws and tap off the loose part of a stile or rail using a hammer, protecting the...
  • REPAIR LOOSE JOINTS. Joints deteriorate as water finds its way in. To fix, dampen the joint...

Full Answer

How much does it cost to repair shutters?

Window shutter repair costs $269 on average. You can expect to pay between $138 and $434. You’ll often hire a window installation professional or a handyman for $20 to $60 per hour. Costs for repairs depend on a few factors including the type of repair, material and accessibility. Sometimes it’s cheaper to replace than to repair.

How can I upcycle shutters?

21 Upcycled Shutter Projects

  • Upcycled Shutter Projects
  • Shutters Used For Hanging Light Fixture
  • Upcycled Shutters Used As Decor
  • Shutters Used In Seasonal Decor. We have several upcycled shutters as decor in our home …. Thanks for stopping by today. ...

How can I renew my shutters?

Method 2 of 3: Cleaning Oxidized Vinyl Shutters

  1. Mix a solution using commercial cleaner. You can purchase a commercial cleaner online or at a local hardware store.
  2. Spray down two shutters at a time with the cleaner. Place your cleaner in a spray bottle or pump garden cleaner.
  3. Wipe down each shutter with a scouring pad. ...
  4. Apply the scratch test. ...
  5. Repeat the process if necessary. ...
  6. Rinse your shutters. ...

How to repaint your shutters?

  • Keep the surface wet long enough for the bleach to do its job. This means you should wait a few minutes before rinsing the shutters.
  • Make sure to protect your eyes and skin as well as any plants when you’re working with bleach.
  • A long-handle scrub brush can help work the solution into hard-to-reach corners. ...

image

How do you fix wood shutters?

2:196:00Repairing A Wood Shutter - YouTubeYouTubeStart of suggested clipEnd of suggested clipBasically you know cut the cedar boy to size the exact width of the rotted board and then I flippedMoreBasically you know cut the cedar boy to size the exact width of the rotted board and then I flipped it over on its edge. And cut it to the same to the same thickness to match.

How do I fix my exterior shutters?

2:077:13How to Replace Vinyl Shutters - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou would drill a quarter inch hole and then you'd use those spikes to kind of do a little bit of aMoreYou would drill a quarter inch hole and then you'd use those spikes to kind of do a little bit of a friction fit.

How do you fix wooden louvers?

0:462:23How to replace a broken shutter louvre blade or pin - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd grab some super glue on the end. Hold the louver blade straight and carefully insert thisMoreAnd grab some super glue on the end. Hold the louver blade straight and carefully insert this vehicle. Use the end of the pliers to push.

How do you fix slats on plantation shutters?

0:281:45How to replace a slat in your push rod shutters - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe slat is dislodged from the panel. Remove this old pin from the panel. Now we're ready to fitMoreThe slat is dislodged from the panel. Remove this old pin from the panel. Now we're ready to fit your new slat. Take your replacement pins. Insert this longer fixed pin like this into the panel.

Can you buy just one shutter?

Matching just one or two exterior shutters on a house can be, and most likely will be, difficult. Finding a company to manufacture a new shutter with the exact same specifications as the old panel is not impossible. However, there will certainly be a very hefty price tag to that request.

How do you fix fallen shutters?

Use a Philips head screwdriver to insert the filler into the hole. Let dry 24 hours before continuing. Locate someone to assist in holding the shutter in place during reattachment. One person should hold the shutter with the screw holes in the shutter aligned with the screw holes in the house.

How do I fix my louver?

Step 1 How to Fix a Loose Louver in Wooden Sliding Shutters. ... Locate the broken or loose louver. ... Align the louvers so they are parallel to the ground. ... Tilt the louver down creating a 30 degree angle with the bar. ... Position the knob in between the two holes. ... Insert the pin into the two holes. ... Push and secure the pin.More items...

How do you secure a loose shutter?

You will need to unscrew the hinge from the shutter and identify which hole(s) have become enlarged. Either step up to a thicker screw or repair the holes by using 2 pack filler* available in tube form that can be squeezed into the hole. Once dry, the excess can be carefully removed and lightly trimmed.

How do you fix slats on louvered doors?

Puncture the tip of a bottle of all-purpose glue with the point of a push-pin. Apply a modest amount of glue into the seam of a crack or split at a louver. Squeeze the upper and lower edges of the louver together and remove any excess glue with a damp sponge.

Can you replace individual shutter slats?

Luckily, shutter slats are held in place with pins that can easily be replaced to reattach any dislodged or damaged slats.

How do you refurbish plantation shutters?

Painting Plantation Shutters: A Step-by-Step GuideStep 1: Remove the shutters from the window. ... Step 2: Remove all hardware. ... Step 3: Give the shutters a thorough clean. ... Step 4: Apply a primer. ... Step 5: Paint the shutters. ... Step 6: Replace all hardware. ... Step 7: Re-hang the shutters.

How do you replace wooden blind slats?

0:112:05How to Change the Slats on your Window Blinds from SelectBlinds.comYouTubeStart of suggested clipEnd of suggested clipSlide the broken slack out of the ladders. Make sure that the replacement slats route holes alignMoreSlide the broken slack out of the ladders. Make sure that the replacement slats route holes align with the rest of the blind. Put the new slat into the open ladder and slide it all the way.

How do you fix manual roller shutters?

A solution to this issue is to spray the components of your roller shutter with a lubricant, such as WD-40. The WD-40 will loosen up the mechanisms, allowing them to move smoothly. Open up the box at the top of your slats and you should be able to investigate further.

How do you fix a hole in a vinyl shutter?

Vinyl adhesive caulk is the best product to repair holes in vinyl. In some cases, caulk can be purchased directly from the manufacturer of the vinyl siding so that is an exact color match.

How do you reattach a shutter to Brick?

2:347:36Attaching Shutters To Brick Homes - YouTubeYouTubeStart of suggested clipEnd of suggested clipBy the screw penetrating it and that will hold the shutters in place with that done I'm going toMoreBy the screw penetrating it and that will hold the shutters in place with that done I'm going to test and make sure my anchors are large enough they do fit a little bit loosely in the holes.

How do you restore old shutters?

Whoever does the work will need to remove the shutters, take off the hardware, strip the old finish, then sand the wood, stain it and coat it with a clear finish — ideally two coats. The final step is putting it all back together and making sure the parts fit as well as they do now.

How to clean a shutter?

Dust off loose dirt with a soft brush. Gently wash the shutter with a rag and soapy water; if it’s excessively dirty, use trisodium phosphate (TSP) diluted with water per instructions. Wear protective gloves, clothing, and eyewear when using TSP. Rinse cleaned shutters with a hose. Let dry completely.

Why do exterior shutters peel?

Whether functional or merely decorative, exterior shutters may suffer from peeling paint, joint problems, and decay because they are exposed to the elements. Movable parts such as louvers may break. Do inspect exterior shutters every year and address problems before they progress to the point where the shutters need to be replaced.

How to secure a slat on a frame?

Tilt the end with the stationary pin into the open slot on the frame. The pin will insert into the slot. Then press the spring-loaded pin down with your finger so that the slat can slide along frame and into the slot. The spring will release into the opening on the slat, securing it.

How to cut a pin out of a slat?

With a utility knife, cut the old pin by sliding the knife between the slat and the frame. Pry out the remains of the pins from the slat and the frame. Tap the stationary pin into one end of the slat. Insert the spring-loaded pin into the stile (not the louver) on the other side.

Why do shutters wiggle back and forth?

A shutter with a loose connection to the house can wiggle back and forth. This puts stress on the outside wood frame of the shutter. Weather conditions and poorly painted shutters can also contribute to the need to repair the frame.

How to fix a broken frame?

Make repairs to the frame by cleaning it first with a stiff brush. Set the louvers back into position and push the interlocking joints back together. Dampen the frame’s joints slightly before you coat the joints with polyurethane glue. Water activates the glue and helps hold the joints together.

How to repair rot on a car frame?

You can repair a small section of wood rot on the frame by chipping out any of the soft, damaged wood with a screwdriver tip. Mix two-part auto-body filler following manufacturer’s directions in a small container. Spread the filler into the damaged area, smoothing the surface with a putty knife.

Do shutters protect windows?

Wooden shutters complement to your house’s exterior siding and give definition to windows. While some shutters are purely decorative, others open and close to protect the windows. Since wooden shutters are a big investment in your home, it only makes sense to keep them in good repair. Removing the shutters from the house ...

Can you sand a louver?

If the damage isn’t too severe to a broken louver, you can sand off the paint and apply wood filler to repair the damaged area. Once the filler dries, sand the louver and paint it again before reinstalling the louver into the shutter. If the louver shows signs of wood rot, you’re better off replacing it. Most shutters have replacement louvers available.

Skill

5 Easy The job becomes a bit more complicated if you must mill new parts for the shutter.

Estimated Time

In this video, This Old House general contractor Tom Silva explains how to repair exterior shutters.

What does it mean to get shutters back in working order?

Getting the shutters back into working order meant scraping paint away from the louvers’ pins and shoulders.

Who inventoried the reusable and unusable components of shutters?

To analyze whether the shutters could be repaired durably for a similar price, Ted took all the parts to his shop, where he and associate Mike Marini inventoried the reusable and unusable components. Like window sash, the shutters were constructed with mortise-and-tenon joints held fast with wood pegs.

What wood do Ted and Mike make shutters from?

Rather than reuse the old, deteriorated stiles, Ted and Mike made new stiles from white oak, a species renowned for durability and its ability to tenaciously grasp hardware screws. Although joining dissimilar woods with glue generally isn’t recommended, in this case it works because the louver pins are moving freely within the stile mortise holes.

How many louvers are there in a shutter?

Disassembling the shutters was easy: Once the pegs were pulled or drilled out, the stiles released from the rails, and the 68 individual louvers fell away from the shutter. Fortunately, the tilt bar, the vertical stick that moves the louvers up or down, kept the numerous pieces in place and maintained the order in which they would be reinstalled.

What was Ted's main concern with the shutters?

Michael’s main concern was that the shutters look appropriate to the house. Ted worried that new shutters wouldn’t look right, and custom-made replicas would be far too expensive. So, he decided to repair the originals on a time and materials basis, estimating that the final cost would be less than or comparable to the new shutter price.

Why are shutters important?

Shutters are inarguably one of a house’s most significant details; historically, they shielded delicate fabrics from the sun, protected fragile glass from inclement weather, and also offered security, privacy, and ventilation. Now merely window dressing, shutters are frequently misunderstood and installed as an afterthought.

Who hangs shutters on the Gothic Revival house?

Ted Robertson hangs the good-as-new shutters on the Gothic Revival house. For homeowner Michael Orman, keeping the shutters on his mid-Victorian Gothic Revival cottage in Rochester, New York—one of many along historic Mt. Hope Avenue designed by nationally and locally famous architects such as Gervase Wheeler, Andrew Jackson Davis, and A.J. and J.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9