How to use the kit
- Connecting everything. Here’s how you use the kit to seal a puncture. ...
- Turning it on. Make sure the compressor’s power is switched off. ...
- Maximum running time. To avoid over inflating the tire, do not let it run longer than seven minutes. ...
- Finishing up. ...
- Check tire pressure. ...
- Turn on compressor again if pressure is low. ...
- Restricted driving after using repair kit. ...
Full Answer
What should be included in a puncture repair kit?
The puncture repair kit should include a can of sealant and a compressor. It may also include warning stickers to place on the wheel and inside the car, to remind you to replace the tyre.
How do I fix a puncture in my car?
Switch off your engine. Turn on your hazard lights. Put the vehicle into 'P' if you’re driving an automatic. Make sure all passengers are out of the car and in a safe place. Get the repair kit out (usually found in the boot). The puncture repair kit should include a can of sealant and a compressor.
Can you use a puncture repair kit to replace a tyre?
If you’ve got a new-ish car, it might have a puncture repair kit instead of a spare tyre to change. A repair kit uses tyre sealant and a compressor to repair the hole in the tyre. Here’s how to safely make a temporary repair so you can drive yourself to a garage.
Can I get a puncture repaired?
If you get a puncture you might be able to get it repaired, for a fraction of the cost of a new tyre, if: A bodged repair could be very dangerous so a British standard (BS AU159) sets out clear rules for the type of damage that can and can’t be repaired and how repairs should be carried out.
How to use a tyre puncture repair kit?
What is a tyre repair kit?
How to fix a tyre that is not protruding?
How to clear a hole in a tyre?
What is a repair cord?
How to make a hole bigger with a reamer?
What is a reamer used for?
See more
About this website
How do you use puncture repair kit?
0:321:44How to use a puncture repair kit (sponsored) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe sealant plugs the hole and a tire and the compressor reinflates it in your puncture repair kitMoreThe sealant plugs the hole and a tire and the compressor reinflates it in your puncture repair kit there should be at least one sticker with a maximum speed warning on it stick.
How long does a puncture repair kit take to dry?
Spread the glue over an area that's larger than the patch with your finger, and then leave it to dry for at least five minutes. Don't do anything else until it's totally dry – otherwise you won't fix your puncture. Once you've peeled off the foil backing, apply the patch, making sure it's centred over the hole.
What is the chalk for in a puncture repair kit?
The chalk prevents the patch from sticking to the inside of the tyre, allowing it to slide around.
Is it better to patch a tire or plug it?
Patches are better than plugs for bigger holes, holes closer to but not the sidewall and holes that aren't completely straight. Note that if you're looking to do tire sidewall repair, a patch will usually not cut it and you'll likely want to replace the tire. Don't patch the tire if it's near the sidewall.
How long does a puncture repair last?
seven to ten yearsOn average, tire experts predict that a proper plug and patch can last from seven to ten years. Although tire patches can last a long time, a tire should never be patched more than once. It can negatively affect the speed rating and potentially cause blowouts.
Can you use super glue to repair a puncture?
Can I use super glue to mend punctures? In summary, super glue cannot be utilized to patch or repair a puncture in tires or their associated inner tubes by its very nature. Cyanoacrylate gum or super blue often gets dry, brittle, and inflexible after prolonged exposure to air.
What is the best way to patch an inner tube?
0:182:06How to Patch a Bicycle Inner Tube - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing the tube of vulcanizing glue from your patch kit start in the center and smear the fluidMoreUsing the tube of vulcanizing glue from your patch kit start in the center and smear the fluid around the hole covering an area that's at least three to four centimetres larger than the patch.
Which way round does a puncture repair patch go?
The orange side is going to stick to the tyre, so be careful not to touch it or get any dirt on it. Make sure the solution is spread in a thin layer across an area that is larger than the patch you want to use. While you are waiting, it's a good time to check the tyre for what caused the puncture in the first place.
How long does it take for a nail to flatten a tire?
All it takes is to run over a nail, and your tire flattens in a matter of seconds. An easy solution would be to watch where you are going and avoid things lying in the road. However, it's difficult to see a nail or jagged shard of metal lying on the road while driving at 55 mph.
Can you drive long distance with a patched tire?
It is safe to drive on a patched tire regardless of how rugged or rocky the road gets. But if you regularly speed on the highways, it would be best to have the tire(s) replaced. It's safe to drive on a patched tire as long as you adhere to the recommended speed limit. You can do the patch yourself.
Can a tyre be repaired after using sealant?
The water based foam seals punctures and won't damage your tyres in any way. It can be wiped out of tyres easily, so a mechanic can repair the puncture permanently. You should tell your mechanic before they remove the tyre that you've used Tyreweld and that it can be cleaned out.
Is a tire plug a permanent fix?
Tire Plugs and String Repairs are Temporary Repairs Emergency roadside plug repairs are NOT intended to be a permanent tire repair. Plugs and string repairs are designed to get you back up and rolling long enough to get home or to the nearest service center to perform a proper tire repair.
How to use a tyre puncture repair kit?
How to use a tyre-puncture repair kit. Be prepared with a good tyre-puncture repair kit, know how to use it and then you'll be ready for action when the time comes. Prevention is better than a cure, everyone knows that, but sometimes things simply happen. In the world of off-roading, tyre punctures are a definite possibility.
What is a tyre repair kit?
A tyre-puncture repair kit should include a carry case and all of the gear you need to achieve a temporary fix of a puncture, which will give you enough leeway on that repaired tyre to safely reach a tyre-repair professional in order to have it properly fixed.
How to fix a tyre that is not protruding?
Hold the tool's metal hilt against the tyre, and pull the insertion tool out. Do not twist the insertion tool's handle. Trim the ends of the repair cord so they aren't protruding too much, inflate your tyre back to the suitable pressure and away you go.
How to clear a hole in a tyre?
Smear the kit's lubricant on the reamer – this is the tool with the spiral, drill-bit-like shaft – then insert the reamer into the puncture to clear the hole. Move the reamer around in the hole, in circles, in order to make the hole a bit bigger, separate the steel belts, then pull the reamer out. Now's the time to reinflate the damaged tyre to help wth insertion of the cord.
What is a repair cord?
Repair cords: Thick strings of spongy cord that you insert into the puncture to fill the hole and make the tyre temporarily safe to drive on. Some kits, like this one, include valve accessories, a blade (to trim the repair cords) and more.
How to make a hole bigger with a reamer?
Insert the reamer into the puncture to clear the hole and make it a bit bigger.
What is a reamer used for?
The reamer is used to probe the puncture, clear away any remaining debris and temporarily separate the tyre's steel belts without damage, helping to smooth the way for the repair cords/plugs. The cord-insertion tool: Looks like a cross between a sewing needle and an ice pick.
What is included in a puncture repair kit?
The puncture repair kit should include a can of sealant and a compressor. It may also include warning stickers to place on the wheel and inside the car, to remind you to replace the tyre.
Where is the puncture on a car?
The puncture is outside of the main tread area.
How fast can you drive on a tyre that has been repaired?
This should be in the instructions but if in doubt, stick to a maximum of 50mph for 50 miles.
How to re-inflate a tyre?
You’ll need to use the compressor to re-inflate your tyre. It may also pump the sealant into the tyre at the same time. Check your vehicle manual to find the right tyre pressure for your vehicle. Make sure your car is in neutral with the handbrake or parking brake on. Turn on the engine and switch on the compressor.
What to do if your tyre sealer is damaged?
If it looks damaged, you’ll need to call us out to help you. If the sealant has worked, you can drive to a garage. You may need to inflate the tyre a bit more first, so check the instructions on the kit and the pressure in your handbook.
How to know if you have prepuncture sealant?
If you’ve used a pre-puncture sealant, check your tyres every time you drive the vehicle. If the sealant’s been activated, you should see signs of the sealant (usually a white rubber-like substance) on the outside of the tyre.
How to fix a car that is not automatic?
Before you try to use the repair kit, make sure you and your passengers are in a safe place and the car’s prepared: Switch off your engine. Turn on your hazard lights. Put the vehicle into 'P' if you’re driving an automatic. Make sure all passengers are out of the car and in a safe place.
How to use a tyre puncture repair kit?
How to use a tyre-puncture repair kit. Be prepared with a good tyre-puncture repair kit, know how to use it and then you'll be ready for action when the time comes. Prevention is better than a cure, everyone knows that, but sometimes things simply happen. In the world of off-roading, tyre punctures are a definite possibility.
What is a tyre repair kit?
A tyre-puncture repair kit should include a carry case and all of the gear you need to achieve a temporary fix of a puncture, which will give you enough leeway on that repaired tyre to safely reach a tyre-repair professional in order to have it properly fixed.
How to fix a tyre that is not protruding?
Hold the tool's metal hilt against the tyre, and pull the insertion tool out. Do not twist the insertion tool's handle. Trim the ends of the repair cord so they aren't protruding too much, inflate your tyre back to the suitable pressure and away you go.
How to clear a hole in a tyre?
Smear the kit's lubricant on the reamer – this is the tool with the spiral, drill-bit-like shaft – then insert the reamer into the puncture to clear the hole. Move the reamer around in the hole, in circles, in order to make the hole a bit bigger, separate the steel belts, then pull the reamer out. Now's the time to reinflate the damaged tyre to help wth insertion of the cord.
What is a repair cord?
Repair cords: Thick strings of spongy cord that you insert into the puncture to fill the hole and make the tyre temporarily safe to drive on. Some kits, like this one, include valve accessories, a blade (to trim the repair cords) and more.
How to make a hole bigger with a reamer?
Insert the reamer into the puncture to clear the hole and make it a bit bigger.
What is a reamer used for?
The reamer is used to probe the puncture, clear away any remaining debris and temporarily separate the tyre's steel belts without damage, helping to smooth the way for the repair cords/plugs. The cord-insertion tool: Looks like a cross between a sewing needle and an ice pick.
