NOCO GENIUS Repair Mode
- Initial Measurements. I used a multi-meter to measure battery voltage before starting. ...
- Normal Charge. NOCO recommends running a battery through a normal charging cycle before attempting to repair. ...
- Repair Mode. With the battery charged, it was time for repair mode. ...
- Subsequent Measurement. ...
Is there a repair mode on the NoCo Genius 5?
NOCO GENIUS Repair Mode NOCO GENIUS Repair Mode ℹ️ As an Amazon Associate I earn from qualifying purchases. (details) Taking the Repair mode for a spin using a NOCO GENIUS 5, attempting to recover an old battery. This is a follow-up to my previous review of the NOCO GENIUS charger/tender series.
What kind of battery does the NoCo genius take?
Perfect candidate for experimenting with the NOCO GENIUS charging and repair modes. The battery was a Panasonic S55D23R, offering 335 CCA and 51 Ah. Not hugely capable, but its only responsibilities were starting the hybrid system and running 12V electronics when the hybrid system was disabled.
How does the genius10 work?
The GENIUS10 automatically detects sulfation/acid stratification. If any is found, the GENIUS10 will automatically repair and reverse the damage done to the battery, extending the usable life and increasing the performance. Year-Round Charging. Zero Overcharge.
What are the benefits of the genius10 battery charger?
Auto Repair. Improved Performance. The GENIUS10 automatically detects sulfation/acid stratification. If any is found, the GENIUS10 will automatically repair and reverse the damage done to the battery, extending the usable life and increasing the performance. Year-Round Charging.
How do I use noco in repair mode?
0:000:56HowTo Noco Genius 5 repair Function Mode #shorts - YouTubeYouTubeStart of suggested clipEnd of suggested clipFunction hold the mode button for three seconds until the six volts light is blinking. Then pressMoreFunction hold the mode button for three seconds until the six volts light is blinking. Then press again and the repair function will be activating and blinking.
How long leave battery in repair mode?
For optimal results, take the 12-volt battery through a full charge cycle, bringing the battery to full charge, before using this mode. 12V Repair can take up to four (4) hours to complete the recovery process and will return to Standby when completed.
How do I use repair mode?
2:485:57The Noco Genius G7200 Charger Repair Mode - Does it work?YouTubeStart of suggested clipEnd of suggested clipThe repair mode all you do is hold the mode. Button down for three seconds. And you can toggleMoreThe repair mode all you do is hold the mode. Button down for three seconds. And you can toggle between the different settings.
How do I use Genius 10?
0:011:21How to use force mode on your NOCO GENIUS10 - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo access force mode ensure the charger is connected to AC power and has a secure connection to theMoreTo access force mode ensure the charger is connected to AC power and has a secure connection to the battery. Then press and hold the mode button for approximately 7 seconds.
What does repair mode do on battery charger?
12V Repair is an advanced battery recovery mode for repairing and desulfating old, idle, damaged, stratified or sulfated batteries. Its important to note, not all batteries can be recovered. Batteries tend to become damaged if kept at a low charge and/or never given the opportunity to receive a full charge.
Can you use noco repair mode AGM battery?
AGM batteries are a type of lead-acid battery, and Repair Mode can be used on them.
When should I use noco genius repair mode?
Using the 12V repair mode will help to reverse the sulfation/stratification build-up inside of the battery. NOTE: USE THIS MODE WITH CARE. THIS MODE IS FOR 12-VOLT LEAD-ACID BATTERIES ONLY. THIS MODE USES A HIGH CHARGING VOLTAGE AND MAY CAUSE SOME WATER LOSS IN WET (FLOODED) CELL BATTERIES.
How do you reset a noco charger?
To reset the charger's memory, you'll first need to have the charger connected to a battery. Plug the charger into AC power, and use the Mode button to put the unit into Standby with the Orange Power LED lit, and then unplug the charger from AC power again.
Can a battery charger repair a car battery?
If a battery is completely dead but has been revived by a jump start, there are ways to fully recharge your battery. The first is, as mentioned, by driving around. If that does not seem to work, however, car battery chargers can regenerate all of the charge into a battery.
Can the NOCO Genius 10 jump start?
Expert Reply: The NOCO # 329-GENIUS10 is a battery charger only, it wouldn't work unless plugged into a 110V AC outlet. To jump start a dead car battery, you'll need a jump box with an on-board battery.
Is the NOCO Genius 10 a trickle charger?
NOCO GENIUS10, 10A Fully-Automatic Smart Charger, 6V and 12V Portable Automotive Car Battery Charger, Battery Maintainer, Trickle Charger and Battery Desulfator with Temperature Compensation.
Can noco charge a dead battery?
Force mode feature is awesome to detect low voltage on a battery to start recover process. Usually a low voltage battery would be 1V-4V. Noco claims the charger can charge a dead battery as low as 1-volt.
How long does a car battery repair take?
30 to 60 minutesA car battery replacement usually takes 30 to 60 minutes. The good news is that most mechanics have new batteries on hand for common makes and models. So, if you drive a common model—and if you can find a same-day appointment—you should be in and out with a new battery in under an hour!
How long does a battery charger take to recondition a battery?
Usually, reconditioning a battery takes around four hours. However, you may not get success in the first attempt, so you can repeat the process until the battery reconditioned fully and get back to its original condition.
How long does it take to recondition a 12 volt battery?
Don't forget that the charging battery should be between 10 and 12 hours, if you use a slow charger. On the other side, if you use a quick charger you can recharge it in less than 6 hours. It is a much better choice to measure the battery levels with a voltmeter, while charging in order to get the best results.
How long does it take to Desulfate a car battery?
48 hours to weeksDepending on the size of the battery, the desulfation process can take from 48 hours to weeks to complete. During this period the battery is also trickle charged to continue reducing the amount of lead sulfur in solution.
How long does the battery repair mode last?
The repair mode lasted about four (4) hours, just as the User Guide suggested. Toward the end I could hear the quiet bubbling sounds of electrolysisemanating from the battery; no steaming, venting of gases, or warmth to the battery casing. The charger returned to Standby mode after completion.
Can you run a battery through a normal charging cycle?
NOCO recommends running a battery through a normal charging cycle before attempting to repair.
Manual
View the manual for the NOCO Genius 10 here, for free. This manual comes under the category Battery chargers and has been rated by 17 people with an average of a 8.4. This manual is available in the following languages: English. Do you have a question about the NOCO Genius 10 or do you need help? Ask your question here
NOCO Genius 10 specifications
Below you will find the product specifications and the manual specifications of the NOCO Genius 10.
Frequently Asked Questions
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the NOCO below.
How long is the Noco warranty?
NOCO warrants that this product (the “Product”) will be free from defects in material and workmanship for a period of Three (3) years from the date of purchase (the “Warranty Period”). For defects reported during the Warranty Period, NOCO will, at its discretion, and subject to NOCO’s technical support analysis, either repair or replace defective products. Replacement parts and products will be new or serviceably used, comparable in function and performance to the original part and warranted for the remainder of the original Warranty Period.
Is the Hassle Free Warranty void?
These conditions apply only to Product during the Warranty Period. The Hassle-Free Warranty is void either by elapsed time from date of purchase (elapsed time from serial number date, if no proof of purchase) or from the conditions listed earlier in this document. Return Product with the appropriate documentation.
How low can a Genius charge a battery?
The all-new start-voltage sensor allows the GENIUS to detect and charge dead batteries as low as 1-volt. For extremely dead batteries lower than 1-volt, manually turn on force mode to detect and charge batteries all the way down to zero volts.
What batteries can be used with genius?
Do more with Genius - Designed for 6-volt and 12-volt lead-acid automotive, marine, and deep-cycle batteries, including flooded, gel, AGM, and maintenance-free, plus lithium-ion batteries.
What is genius clamp?
Genius clamps are built with needle-nose profiles for smaller terminal applications and detachable integrated eyelets for permanent mounting the accessory to battery. Designed to fit battery terminals of any shape and size. Engineered for improved clamping range, clamping force, and higher conductivity.
Does genius charger work?
Finally a charger from start to finish that’s completely automatic. No special modes, no technical knowledge required. Genius will safely charge any battery. Detect damaged batteries and intuitively repair them. And actively monitor for long-term battery maintenance and extend battery life. This system allows for continuous operation without user intervention, and zero risk of overcharging your battery.
Initial Measurements
Normal Charge
- NOCO recommends running a battery through a normal charging cycle before attempting to repair. Connect the positive clamp, then the negative, then plug in the charger. Note: I plugged the charger into an inexpensive power meterto observe the voltage, amperage, power, and total kWh used throughout the charging and subsequent repair process. The battery in question was …
Repair Mode
- With the battery charged, it was time for repair mode. Press and hold the Mode button for 3 seconds until the 6V LED illuminates, then press the Mode button once more to switch to 12V Repair mode. A red LED will illuminate. The repair mode lasted about four (4) hours, just as the User Guide suggested. Toward the end I could hear the quiet bubbling ...
Subsequent Measurement
- To see how the battery was holding the charge, I took measurements for a few days after completing the repair. 1. 0 hours: 13.20 VDC 2. 24 hours: 12.94 VDC 3. 48 hours: 12.84 VDC 4. 72 hours: 12.77 VDC 5. 96 hours: 12.73 VDC The battery appears to be losing 1-2% of its initial charge every day. If discharge continues at that rate, the vehicle would need to be driven (or bat…