With the battery charged, it was time for repair mode. Press and hold the Mode button for 3 seconds until the 6V LED illuminates, then press the Mode button once more to switch to 12V Repair mode. A red LED will illuminate. The repair mode lasted about four (4) hours, just as the User Guide suggested.
Full Answer
Can the NOCO Genius 5 recover an old battery?
Taking the Repair mode for a spin using a NOCO GENIUS 5, attempting to recover an old battery. This is a follow-up to my previous review of the NOCO GENIUS charger/tender series. The accessory battery from a friend's Toyota hybrid was dying as soon as the hybrid system was disabled.
What is 12V repair on the g3500 and G7200?
NOTE: This article applies directly to the G3500, G7200, G15000, and G26000 chargers, but contains information relevent to all chargers. 12V Repair is an advanced battery recovery mode for repairing and restoring, old, idle, damaged, stratified or sulfated batteries. Not all batteries can be recovered.
What do the LEDs mean on the g3500 smart charger?
Read below for an overview on the G3500 Smart Charger. 1.) Mode Button The Mode Button allows for switching between different smart charging options. 2.) Error LED All error conditions are displayed with the Error LED and Standby LED light flashing back and forth.
How do I use noco Genius g3500 repair mode?
0:000:56HowTo Noco Genius 5 repair Function Mode #shorts - YouTubeYouTubeStart of suggested clipEnd of suggested clipFunction hold the mode button for three seconds until the six volts light is blinking. Then pressMoreFunction hold the mode button for three seconds until the six volts light is blinking. Then press again and the repair function will be activating and blinking.
When should I use repair mode noco genius?
Using the 12V repair mode will help to reverse the sulfation/stratification build-up inside of the battery. NOTE: USE THIS MODE WITH CARE. THIS MODE IS FOR 12-VOLT LEAD-ACID BATTERIES ONLY. THIS MODE USES A HIGH CHARGING VOLTAGE AND MAY CAUSE SOME WATER LOSS IN WET (FLOODED) CELL BATTERIES.
How do I use repair mode?
2:485:57The Noco Genius G7200 Charger Repair Mode - Does it work?YouTubeStart of suggested clipEnd of suggested clipThe repair mode all you do is hold the mode. Button down for three seconds. And you can toggleMoreThe repair mode all you do is hold the mode. Button down for three seconds. And you can toggle between the different settings.
How long leave battery in repair mode?
For optimal results, take the 12-volt battery through a full charge cycle, bringing the battery to full charge, before using this mode. 12V Repair can take up to four (4) hours to complete the recovery process and will return to Standby when completed.
Can I use repair mode on AGM battery?
AGM batteries are a type of lead-acid battery, and Repair Mode can be used on them.
What does repair mean on a battery charger?
12V Repair is an advanced battery recovery mode for repairing and desulfating old, idle, damaged, stratified or sulfated batteries. Its important to note, not all batteries can be recovered. Batteries tend to become damaged if kept at a low charge and/or never given the opportunity to receive a full charge.
How do I use noco Genius 10 repair mode?
With the battery charged, it was time for repair mode. Press and hold the Mode button for 3 seconds until the 6V LED illuminates, then press the Mode button once more to switch to 12V Repair mode. A red LED will illuminate. The repair mode lasted about four (4) hours, just as the User Guide suggested.
How do you reset a noco charger?
To reset the charger's memory, you'll first need to have the charger connected to a battery. Plug the charger into AC power, and use the Mode button to put the unit into Standby with the Orange Power LED lit, and then unplug the charger from AC power again.
Can a battery charger repair a car battery?
If a battery is completely dead but has been revived by a jump start, there are ways to fully recharge your battery. The first is, as mentioned, by driving around. If that does not seem to work, however, car battery chargers can regenerate all of the charge into a battery.
When should you Desulfate a battery?
Dispose of the battery. If each cell floats three (3) or more balls (or 1250 on gauge-type), your battery can be reconditioned-desulfated. Always rinse the tester with fresh water after every use. Failure to do so will cause false readings.
How do you fix a sulfated battery?
Reversible sulfation can often be corrected by applying an overcharge to an already fully charged battery in the form of a regulated current of about 200mA. The battery terminal voltage is allowed to rise to between 2.50 and 2.66V/cell (15 and 16V on a 12V mono block) for about 24 hours.
How does the noco genius work?
The NOCO Genius GEN charger is an 8 step, fully automatic switch-mode battery charger which automatically determine the condition of your battery before beginning it's charge cycle. It will only charge when the battery needs it, and will fully maintain your battery when it is in storage or between uses.
When should you Desulfate a battery?
Dispose of the battery. If each cell floats three (3) or more balls (or 1250 on gauge-type), your battery can be reconditioned-desulfated. Always rinse the tester with fresh water after every use. Failure to do so will cause false readings.
How does a pulse repair battery charger work?
3:527:21Review Of The Foxsur Pulse Repair Car Battery Charger - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou'll see the the charge voltage 13 point nine volts and the charge current which is four pointMoreYou'll see the the charge voltage 13 point nine volts and the charge current which is four point four amps. If there's a fault with the unit or the way you can exit it this light will illuminate.
How do you fix a sulfated battery?
Reversible sulfation can often be corrected by applying an overcharge to an already fully charged battery in the form of a regulated current of about 200mA. The battery terminal voltage is allowed to rise to between 2.50 and 2.66V/cell (15 and 16V on a 12V mono block) for about 24 hours.
Does noco Genius 2 have repair mode?
Press and hold the Mode button for 3 seconds until the 6V LED illuminates, then press the Mode button once more to switch to 12V Repair mode. A red LED will illuminate. The repair mode lasted about four (4) hours, just as the User Guide suggested.
How long does the battery repair mode last?
The repair mode lasted about four (4) hours, just as the User Guide suggested. Toward the end I could hear the quiet bubbling sounds of electrolysisemanating from the battery; no steaming, venting of gases, or warmth to the battery casing. The charger returned to Standby mode after completion.
Can you run a battery through a normal charging cycle?
NOCO recommends running a battery through a normal charging cycle before attempting to repair.
Initial Measurements
Normal Charge
- NOCO recommends running a battery through a normal charging cycle before attempting to repair. Connect the positive clamp, then the negative, then plug in the charger. Note: I plugged the charger into an inexpensive power meterto observe the voltage, amperage, power, and total kWh used throughout the charging and subsequent repair process. The battery in question was …
Repair Mode
- With the battery charged, it was time for repair mode. Press and hold the Mode button for 3 seconds until the 6V LED illuminates, then press the Mode button once more to switch to 12V Repair mode. A red LED will illuminate. The repair mode lasted about four (4) hours, just as the User Guide suggested. Toward the end I could hear the quiet bubbling ...
Subsequent Measurement
- To see how the battery was holding the charge, I took measurements for a few days after completing the repair. 1. 0 hours: 13.20 VDC 2. 24 hours: 12.94 VDC 3. 48 hours: 12.84 VDC 4. 72 hours: 12.77 VDC 5. 96 hours: 12.73 VDC The battery appears to be losing 1-2% of its initial charge every day. If discharge continues at that rate, the vehicle would need to be driven (or bat…