How to fix a Kenmore washing machine agitator?
How to Repair a Kenmore Washer That Won't Agitate
- Open the Kenmore washer's lid and pry the cap off the top of the agitator, using a flathead screwdriver.
- Remove the bolt from the center of the agitator, using a 7/16-inch socket and extension. Lift the agitator out of the tub and set it aside.
- Place the agitator on the floor and hold the base with your feet. ...
How to troubleshoot a whirlpool Cabrio washer?
Whirlpool Cabrio Washer Not Spinning
- Check Drive Pulley Nut. The nut that keeps the drive pulley together can become loose over time. ...
- Faulty Shift Actuator. Washers are one of the most convenient ways to get your clothes clean at home, but they can also be one of the most frustrating.
- Check Lid Switch. ...
- Drive Belt Issues. ...
- Defective Door Latch. ...
How to change the agitator in a hotpoint washer?
How to Change the Agitator in a Hotpoint Washer Unplug your Hotpoint direct-drive washer from the wall outlet. Open the lid on your appliance to access the agitator. Install a socket extension onto a socket wrench and connect a 7/16-inch socket to the extension. Spread a towel onto the floor. Remove the socket wrench from the extension and socket.
How to fix a washer that will not agitate?
Washer Will Not Spin and/or Agitate
- Too Large of Loads. A washing machine will become unbalanced if there are too many clothes being washed in the same load.
- Switches and Settings. The lid switch is located inside the cabinet near the door frame, and it's designed as a safety precaution to keep hands from entering a spinning washer ...
- Drain Pump. ...
- Belts. ...
- Motor. ...
What happens if your Whirlpool washer stops agitating?
How to remove agitator cap on washing machine?
Does Whirlpool have a dog agitator?
Does Whirlpool have a fabric softener dispenser?
See 1 more
About this website
How do I fix the agitator on my Whirlpool washer?
4:215:46Replacing the Agitator Repair Kit (Whirlpool Part # 285811) - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe'll take our new bolt. Put it on our ratchet tilt the whole agitator upside down line up that boltMoreWe'll take our new bolt. Put it on our ratchet tilt the whole agitator upside down line up that bolt with a hole. Now we're ready to put it back in the washer now the agitator is ready to install.
How do I put my whirlpool agitator back together?
2:185:36How To: Whirlpool/KitchenAid/Maytag Washer Complete Agitator ...YouTubeStart of suggested clipEnd of suggested clipOnce you have the thrust washer in we're gonna show you that there's a couple locking tabs rightMoreOnce you have the thrust washer in we're gonna show you that there's a couple locking tabs right here on the lower edge stater. They're locked into these locking clips on the agitator dog assembly.
How do you change a whirlpool agitator repair kit?
2:026:54Washer Agitator Repair Kit, Medium Cam (part #285811) - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou'll have to pry off the cap with a flathead screwdriver. Most models have a dust cap. We need toMoreYou'll have to pry off the cap with a flathead screwdriver. Most models have a dust cap. We need to pull it out so we can get to the agitator. Bolt.
How do you fix the agitator on a top load washer?
0:392:50How to Clean, Remove and Replace the Agitator in your Washing MachineYouTubeStart of suggested clipEnd of suggested clipAnd good clean the best way to do this is with warm soapy water and a softer clock. Once theMoreAnd good clean the best way to do this is with warm soapy water and a softer clock. Once the agitator and inner drum a clean again we can replace the agitator. This just pops back in locate.
How do you take apart a whirlpool agitator?
0:051:38AGITATOR REMOVAL—WHIRLPOOL WASHER - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce you get it spun out you can just reach in from the bottom and grab the bottom part of theMoreOnce you get it spun out you can just reach in from the bottom and grab the bottom part of the agitator. And pull up probably good to reach in with two hands so you have a little bit more leverage.
How do you put a washing machine agitator back together?
2:204:48How To: Whirlpool/KitchenAid/Maytag Complete Agitator Assembly ...YouTubeStart of suggested clipEnd of suggested clipAnd just use the bolt to put it together. But I like to put it together the way I came out makes itMoreAnd just use the bolt to put it together. But I like to put it together the way I came out makes it easier to carry around and then insert the cam assembly into the upper agitator.
How do you remove the agitator from a Whirlpool top load washer?
0:061:02Whirlpool Top Load Washer Agitator Assembly #3951744 - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo replace the agitator on your washer first remove the fabric dispenser. You can use a flatheadMoreTo replace the agitator on your washer first remove the fabric dispenser. You can use a flathead screwdriver to help pry it off if necessary. Pull out the agitator cap.
How do I fix my agitator?
0:296:51How to Fix Washer Top Agitator Not Working - YouTubeYouTubeStart of suggested clipEnd of suggested clipSometimes this comes off by hand other times you may need to actually use the ratchet. Hold theMoreSometimes this comes off by hand other times you may need to actually use the ratchet. Hold the agitator down bottom in place he needs.
How do I know if my washing machine agitator is broken?
The agitator should start to oscillate back and forth, mixing up the clothes in the water. If the agitator does not move, double check that the sensor is depressed. If it still does not move with the sensor depressed, the agitator is broken and should be repaired.
What causes a Whirlpool washer not to agitate?
1:232:38Top-Load Washer Won't Agitate — Washing Machine TroubleshootingYouTubeStart of suggested clipEnd of suggested clipThe coupler can wear out over time or fail if the washer is overloaded causing the tub not toMoreThe coupler can wear out over time or fail if the washer is overloaded causing the tub not to agitate.
What causes an agitator to stop working?
A major reason that your washing machine has stopped agitating may be that there's a fault with the drive belt. The belt could be slipping because it's loose or it may have snapped completely. If you're going to fix an issue like this you'll need to be fairly handy or call a repairperson for help.
How do I fix the agitator on my washing machine?
2:2611:01Washing Machine Won't Agitate - Top 8 Problems and Fixes - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou may have splines or flats that lock onto the shaft. If they're worn out the coupling will spinMoreYou may have splines or flats that lock onto the shaft. If they're worn out the coupling will spin freely on the shaft. And the washer won't agitate. If that's the case you'll need to replace it.
How do you fix a loose agitator in a washing machine?
2:094:12WASHING MACHINE AGITATOR LOOSE—EASY FIX - YouTubeYouTubeStart of suggested clipEnd of suggested clipI'll wrap it running I wrap it on really tight. And this would just buy you some time this mayMoreI'll wrap it running I wrap it on really tight. And this would just buy you some time this may actually even work for a month or two.
How do you remove the agitator from a Whirlpool top load washer?
0:061:02Whirlpool Top Load Washer Agitator Assembly #3951744 - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo replace the agitator on your washer first remove the fabric dispenser. You can use a flatheadMoreTo replace the agitator on your washer first remove the fabric dispenser. You can use a flathead screwdriver to help pry it off if necessary. Pull out the agitator cap.
How do I fix my agitator?
0:296:51How to Fix Washer Top Agitator Not Working - YouTubeYouTubeStart of suggested clipEnd of suggested clipSometimes this comes off by hand other times you may need to actually use the ratchet. Hold theMoreSometimes this comes off by hand other times you may need to actually use the ratchet. Hold the agitator down bottom in place he needs.
How do you remove the agitator from a Whirlpool Thin Twin?
0:472:23Whirlpool Washer Agitator Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere's a 7/16 inch bolt down in the agitator remove it and the agitator should come out.MoreThere's a 7/16 inch bolt down in the agitator remove it and the agitator should come out.
Whirlpool washer spins, but won't agitate - Appliance Repair Forum ...
My Whirlpool washer will not agitate. It performs all other functions, including drain & spin. I replaced the agitator assembly (dogs, etc) in the top of the agitator, although they worked fine.
How To Repair A Washing Machine That Won't Agitate - Fix.com
When the washing machine is making a crunching or grinding noise, and the agitator’s upper part isn’t moving smoothly, or is actually frozen in place, it is a good idea to examine the agitator cogs (also known as dogs).
Washer fills with water, doesn't agitate but will spin out water? - iFixit
My bet would be the agitator kit Agitator Repair Kit If the washer won't agitate this agitator repair kit may solve the problem. The kit contains the components that wear out over time. This is a relatively easy repair. Drive Block or Bell If the washer won't agitate the drive block or bell might... - Whirlpool Washing Machine
What happens if your Whirlpool washer stops agitating?
If your Whirlpool washer stops agitating, the racheting pawls may be worn out or broken. The fix is inexpensive and easy, even for a beginner.
How to remove agitator cap on washing machine?
Remove the washing machine agitator cap by prying up around the outer edge with a small flat-blade screwdriver. Then unscrew the center hold-down (Photo 1). Reach in and remove the ratchet assembly. Turn it upside down and remove the snap-in retaining plate (Photo 2). Then install the new agitator dogs and retaining plate (Photo 3). Then reinstall the ratcheting assembly, tighten and pop on the lid.
Does Whirlpool have a dog agitator?
The ratcheting pawls (called “dogs”) can wear out with age, or break if you overload the machine. When that happens, the washing machine agitator dogs won’t rotate . The parts are cheap (less than $5 at appliance repair stores) and the repair is easy. Whirlpool used two ratchet designs, depending on whether the washer has a plain agitator or one equipped with a fabric softener dispenser. Replacing the agitator dogs in a plain agitator is more complicated and that’s the one we show here.
Does Whirlpool have a fabric softener dispenser?
Whirlpool used two ratchet designs, depending on whether the washer has a plain agitator or one equipped with a fabric softener dispenser. Replacing the agitator dogs in a plain agitator is more complicated and that’s the one we show here.
What to do if washer won't agitate?
If the washer won't agitate, replacing the agitator repair kit may solve the problem . The kit contains the agitator components that are most likely to wear out and/or fail. If any of the parts are worn out, stripped, or damaged, replace the kit.
What does a door lock do on a washer?
The door lock secures the washer door shut during operation. Once the washer door is closed, the washer can begin operating. If the door lock is defective, the washer door will not latch properly. The door lock can fail either mechanically or electrically. Inspect the door lock for damage. If the door lock is damaged or does not latch properly, replace it. To determine if the door lock has failed electrically, use a multimeter to test each of the door lock switches for continuity.
Can an agitator be stripped?
The agitator might be damaged or stripped away where it connects to the drive system inside. To determine if the agitator is stripped inside remove it from the washer and inspect for damage or wear.
What is the agitator in a washer?
The agitator is what creates the thrusting motion in your washer to tumble your clothes during the washer cycle. Your agitator will rotate one way, and not the other. The agitator dogs are what prevent the agitator from rotating in both directions, while allowing it to rotate in one direction.
What is an agitator repair kit?
This agitator repair kit comes with a long cam, a thrust spacer and four dogs ears (agitator cogs). This repair kit is used to move the upper agitator and it connects the base of the agitator with the agitator top (mover). This part has been updated by the manufacture.
How many bolts does a washer agitator have?
One bolt held the entire agitator unit in the washer, as well as held the upper and lower halves together. Once that nut was removed the two halves seperated and the plastic clutch pieces could easily be replaced wtih the new onces in the repair kit.
What is a washer retainer ring?
This is a genuine OEM thrust spacer for your washer , and is also commonly known as a retainer ring. The spacer is about 2.5 inches in diameter, is made of plastic, and is white in color. It is used in the agitator assembly of many direct drive washing machine models.
How to remove plastic cup from agitator?
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
What happens if your agitator is not working?
If your agitator is no longer agitating properly, your clothes will not tumble, and will not be washed properly. The agitator repair kit includes an agitator cam, 4 directional cogs, a bearing, thrust spacer, inner cap seal, and a washer. It is constructed of plastic and rubber, and comes in black/white. See more...
Does the agitator come with a cap?
This agitator comes with the 4 agitator dogs (cogs) and top mover. The cap is NOT included with the agitator.
Whirlpool washer direct drive motor coupling had gone bad and washer was not spinning or agitating
My whirlpool washer was no longer spinning, so my first stop was YouTube where I found the video from AppliancePartsPros showing how to replace the motor coupling. In addition to the replacement guide, Matt also shows you how to diagnose the problem by looking for rubber shavings under the washer.
My whirlpool washer would not spin
A couple of years ago, I had an issue with my Whirlpool washer which is every bit of 18 years old. I checked the internet for what might be wrong and stumbled across some how to videos on how to fix it. So, the other day, when my washer quit spinning the first thing I did is go to the internet again to see if I would be able to fix again.
The washing machine would not spin clothes
I searched the internet for the most likely cause of the problem and then went to the AppliancePartsPros.com site to see if they had the parts. Naturally they did, but the best part was that they had a video on how to change the part. The video was very clear and straightforward. So easy to follow. I ordered the part mid-day on a Thursday.
Whirlpool lsr7233eq0 washing machine was leaking out the bottom
I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else.
Kenmore top load washer (25 years old!!!) top agitator not working
Last week I noticed that the Top Agitator wasn't working - I mentioned it to my Wife and she wasn't aware of any problems except Washing Powers not dissolving completely...I thought in my mind that it was finally time to replace our Kenmore Washer & Dryer after 25 years of service!!! I had mentioned the problem I was having with my Manager last week and he shared a simular experience he had some weeks ago...He suggested I check the 'Agitator Doge' and said that I would probably find them in- Read More... pieces!!! Well the first thing I did was perform a Google Search on the problem we were experiencing with this Washer...I came across the AppliancePartsPros.com site where there was a Video describing the repair process for the problem we were experiencing...The video was easy to follow and very through...
My whirlpool washer would not spin
A couple of years ago, I had an issue with my Whirlpool washer which is every bit of 18 years old. I checked the internet for what might be wrong and stumbled across some how to videos on how to fix it. So, the other day, when my washer quit spinning the first thing I did is go to the internet again to see if I would be able to fix again.
Not spinning clothes dry
Replaced clutch assembly, gearcase input shaft seal and motor coupler. When I disassembled the washer I realized the shaft seal on the top of the gearcase was leaking and not the input shaft seal. So had to order more parts before I could finish this job.
What is a Whirlpool agitator dog?
The agitator dog is an essential part of the washer's clutch and works to engage the agitator. New agitator dogs may be needed if the top agitator is no longer moving or if the machine is making a grinding noise.
Where is the drive belt on a washing machine?
This is a replacement main drive belt used in a variety of washing machines. The drive belt is is located underneath the washing machine. It ensures the splotch pulley is driven when the washing machine is being used. This belt moves through the splotch pulleys and the motor to make the washer basket rotate.
What happens if your Whirlpool washer stops agitating?
If your Whirlpool washer stops agitating, the racheting pawls may be worn out or broken. The fix is inexpensive and easy, even for a beginner.
How to remove agitator cap on washing machine?
Remove the washing machine agitator cap by prying up around the outer edge with a small flat-blade screwdriver. Then unscrew the center hold-down (Photo 1). Reach in and remove the ratchet assembly. Turn it upside down and remove the snap-in retaining plate (Photo 2). Then install the new agitator dogs and retaining plate (Photo 3). Then reinstall the ratcheting assembly, tighten and pop on the lid.
Does Whirlpool have a dog agitator?
The ratcheting pawls (called “dogs”) can wear out with age, or break if you overload the machine. When that happens, the washing machine agitator dogs won’t rotate . The parts are cheap (less than $5 at appliance repair stores) and the repair is easy. Whirlpool used two ratchet designs, depending on whether the washer has a plain agitator or one equipped with a fabric softener dispenser. Replacing the agitator dogs in a plain agitator is more complicated and that’s the one we show here.
Does Whirlpool have a fabric softener dispenser?
Whirlpool used two ratchet designs, depending on whether the washer has a plain agitator or one equipped with a fabric softener dispenser. Replacing the agitator dogs in a plain agitator is more complicated and that’s the one we show here.
