
Common toilet repairs include:
[4]- Replace the tank float ball and float rod – $111
- Install a new flapper and chain in the tank. Adjust the linkage and check – $129
- Replace the toilet seat– $62–$189 (depends on the type and size of the seat)
- Remove and reseat toilet with new seal and bolts – $225
How much is the average cost of replacing a toilet?
This does not include the price of the toilet, which averages $99 to $199, for a total toilet replacement cost of $221 to $427. A high-efficiency toilet with extra features can cost $800 to $1,500 to install. The average installation takes a plumber 2 to 4 hours at $65 per hour.
How much does a plumber cost to repair a toilet?
Toilet repairs from a professional plumber cost $130 to $310 on average. For around $150, a pro can fix either the flapper and chain adjustment, the toilet flange, flush valve, or wax ring. Many repairs are fairly simple and can cost as little as $20 to fix it yourself.
How much does it cost too pull and reset toilet?
While removing and resetting a toilet may seem like a big job, mechanically it is one of the easier DIY tasks there is. While a professional plumber can change as much as $200 for a service call to reset a toilet, a DIYer can do it for just $10 to $20, the cost of a new wax ring.
How much to get a new toilet installed?
- Self-Cleaning Toilet – These are very easy to clean, but they are a bit expensive. You can get them at a cost of $500.
- Heated Toilet – These toilets fit perfectly in many homes. ...
- Smart Toilet – These toilets come with advanced features such as MP3 players, inbuilt bidets, and self-closing lids. ...
- Bidet– A bidet is installed together with the toilet. ...

How much does it cost to replace toilet parts?
Toilet Repair Cost by Type of Replacement. Replacing toilet parts can run you between $50 and $3,900 for replacement. As well as having broken parts repaired, you may also need to replace them. Sometimes, parts like the flange or flapper are simply too damaged to fix or are cheaper to replace than fix.
How much does it cost to repair a clogged toilet?
The national average cost to unclog a toilet is $200 to $700, with most people spending about $350 for a plumber to use an electric auger to clear the toilet drain clog and test the system. This project's low cost is $100 for a simple drain snaking or professional chemical treatment by a plumber.
Is it worth rebuilding a toilet?
It Needs Too Many Repairs If there's a crack or any other type of damage to your toilet, rebuilding it can be costly. While some minor repairs—like replacing the flapper, fill valve, or the handle—are cheap and quick to fix, a major rebuild is very expensive.
How much should it cost to reset a toilet?
While a professional plumber can change as much as $200 for a service call to reset a toilet, a DIYer can do it for just $10 to $20, the cost of a new wax ring. It does require careful work, however, to ensure that you don't crack or otherwise damage the toilet as you move it.
How much do plumbers charge to snake a toilet?
The average plumber cost to snake a drain is $100 to $275 for a toilet, sink, tub, shower, or laundry drain. The average cost to snake a main line is $150 to $500. Roto-Rooter prices are $225 to $500 on average to snake a drain. Drain snake rental costs $30 to $80 per day.
How does a plumber unclog a toilet?
1:013:06How to Unclog a Toilet (Like a Plumber) | The Art of ManlinessYouTubeStart of suggested clipEnd of suggested clipAnd use it to form a solid seal over the exit hole don't just focus on the downward push whenMoreAnd use it to form a solid seal over the exit hole don't just focus on the downward push when plunging. The pull back is just as important. Give a few good up-and-down strokes with the plunger.
What is the lifespan of a toilet?
around 50 yearsMost plumbers agree that an average toilet can last around 50 years. However, this is only when the toilet is well maintained and gently used. If it was improperly installed or frequently misused, it may not last as long.
Is it better to replace a toilet or fix it?
If your toilet won't flush or has trouble flushing completely, it needs a repair, and the job should be relatively straightforward. You might need to replace the handle or the flapper. In some cases, you only need to tighten the handle or adjust the length of the chain attached to the handle.
Is it better to fix or replace a toilet?
An occasional repair is normal, but if you're constantly having to fix toilet issues, that can become a costly and time consuming problem. One or two toilet issues is to be expected, but if you are frequently and consistently running into the same problem, or even multiple problems, a new toilet is the way to go.
How much does Home Depot charge to install a toilet?
How much are the installation costs? Home Depot does not hire installers; instead, they subcontract the work to local plumbers and electricians. However, this is something that you should not be worried about as they will still offer top-notch service. On average, the toilet installation costs are $269.
When I flush my toilet nothing happens?
If you push the flush handle and nothing happens, you may have a broken chain on your hands. For example, inside your toilet tank are a flapper and a chain. When you flush, the movement of the handle pulls the chain, which in turn lifts the flapper. As the flapper moves up, it signals the toilet to drain.
What is the labor cost to install a toilet?
On average, a standard toilet installation costs between $120 and $230 for labor with most homeowners spending around $150 to $180. This does not include the price of the toilet which averages $100 to $200 for a total toilet replacement cost of $220 to $430. Get free estimates from plumbers near you.
How do you unclog a toilet when there's nothing works?
How To Unclog Toilet When Nothing Works?Use Plunger. ... Combination of Baking Soda and Vinegar. ... Try a Plumbing Snake. ... Use Dish Soap and Hot Water. ... Suck out the Clog with Wet/Dry Cleaner. ... Using Wire Hanger. ... Use an Enzyme Product. ... Use Chemical Drain Cleaner.More items...
Does Roto Rooter unclog toilets?
Roto-Rooter plumbers are on call 24/7 to unclog your toilet and restore full drainage and powerful flushes. Our skilled plumbers can also fix any other toilet problems, including running toilets, leaking toilets, broken tanks and bowls, and toilets that don't flush properly.
How much does it cost to fix a toilet?
Waiting to repair your toilet can lead to more damage due to leaking water, which causes your repair bill to rise. In general, the national average is $100 to $200 for toilet repairs. Most homeowners pay $150 for a handyman to replace a flapper, but prices vary depending on the amount of work and parts involved.
How much does a plumber charge to fix a toilet?
In most cases, a handyman charges a flat fee of around $60 to $250 for the job, while plumbers charge an hourly rate, which ranges from $45 to $200. Plumbers are more likely to have the part on hand to fix your toilet quickly, while a handyman may need to purchase the part and return, which could slow down the repair.
What happens if a toilet is clogged?
Toilet clogs are a common issue that need to be repaired quickly. Once a toilet is clogged, water simply builds up with each flush and cannot flow through the drain. This can happen due to too much paper or material in the toilet or if a child puts a toy or object into the toilet bowl and flushes it. The plumber may need to use a plunger to unclog the toilet or remove the toilet entirely to look at the pipes. Therefore, costs vary from $150 to $600.
What is a flapper in a toilet?
The flapper is a rubber component of the toilet that sits against the flush valve opening. In some older toilets, the tank ball does the work of the flapper. The flapper blocks the flush valve while water is in the tank and then allows that water to flow down into the bowl when the chain or handle is pulled.
What is the purpose of a toilet bowl?
The toilet bowl is the main body of the toilet that fills with water and is covered by the seat. Little issues can happen with toilet bowls over time. They may become marked, cracked, or damaged due to accidents, and a broken bowl increases the chances of leaks or wobbliness in the toilet. Epoxy resin can be used to repair cracks and breakages in the bowl, or a handyman might need to remove and repair it for significant damage, with average costs of $100 to $300.
Why do toilet flanges corrode?
The flange can also get damaged or simply degrade over time. It can crack, leak, stain, or corrode due to excessive exposure to water and grime. If it breaks, leaks may develop, and the toilet might become unusable.
How much does it cost to replace a toilet shut off valve?
Replacing a shut-off valve is very simple and costs about $60 to $120.
What to do if you don't have a plumber?
If you don't have a plumber you can trust, ask around for recommendations. Your friends, family and neighbors can all give you names of individuals they trust. You can also check Angie’s List for reviews and ratings of local plumbers.
Can a plumber remove a toilet?
A plumber can typically dispatch a clog with a plunger or drain snake. However, severe blockages can require removing the toilet. The severity of the clog and level of work needed to clear it determines the cost.
What is a syphon in a toilet?
The syphon is an integral part of the bowl that allows the toilet to flush. If your syphon stops working, you will need to replace the bowl and/or the entire fixture. Please see Bowl section above, or Replace Toilet section below for pricing information.
How much does a plumber charge?
In some cases, a professional plumber will charge a flat rate for a project. Depending on location, a pro might charge anywhere from $45 to $150 per hour for their services. In rural areas, the cost of hiring a plumber usually falls on the lower end of the scale at $45 to $75 per hour. In more expensive, urban areas, ...
How much does it cost to fix a toilet?
Homeowners pay an average of $237 to fix a broken toilet. Project costs typically range from $148 and $342. In some cases, a professional plumber will charge a flat rate for a project. Depending on location, a pro might charge anywhere from $45 to $150 per hour for their services.
How much does it cost to replace a wax seal?
Replacing a wax ring, also referred to as a wax seal, will run between $50 and $200, including labor and materials. While the ring itself is inexpensive at $2 to $10, replacing it takes time and expertise. The closest flange may also need replacing, which can increase total project price.
Can a plumber clear a clogged sewer line?
Often, a plumber opens a clogged fixture only to find a child's toy blocking the pipes. If you cannot clear it with a household plunger, the clog may be too far down the sewer line and need a professional to snake out the line. Most plumbers bill their services per hour, but some will have a set price to clear a clog.
Do you need a new valve for a noisy fixture?
A homeowner may be able to save money by doing some of these jobs him/herself. Fill valves refill the tank and bowl to the correct water levels after flushing. A noisy fixture or one that is slow to fill may need a new valve.
Factors That Influence the Cost of Repairing a Toilet
The part that needs to be repaired or replaced will influence the final bill significantly. As mentioned above, a simple job such as replacing the wax ring will only cost you a few tens of dollars, but more complex projects can amount to hundreds of dollars.
Common Toilet Parts That Break And Their Costs
A toilet is made of many different moving parts that can wear and tear over time. Here are some of the most common toilet parts that break and the average cost to fix or replace them.
Can We Help?
Do you have a plumbing problem? Call us now at 831-431-6593 and schedule a service.
What to do if toilet clogs up?
If you are not certain what you are doing, you should call in a professional plumber to take care of the problem.
What happens if a toilet is not working properly?
Of course, when the toilet is not working properly, it can cause many people to panic. It’s something that we use every single day. Many different types of problems can arise when it comes to ...
Why does my toilet keep running?
It might keep running, there could be a leak where the toilet connects to the floor, it might not flush properly or at all, or it could be filling slowly. It seems that there are countless potential toilet issues that can happen. When something goes wrong, you want ...
Can you take care of a toilet on your own?
Many toilet issues can be taken care of on your own with the right tools and a little knowledge gained from home improvement websites and videos that cover the problem .
Is it cheaper to replace a toilet?
If the toilet continually needs to have repairs, you might find that it will be cheaper to replace the toilet than to keep making those repairs. It will be less of a hassle, as well. Some plumbers will have fixed rates for certain types of repairs rather than hourly rates. This can give you a better idea of how much the overall cost will be ...
How to fix a toilet that stops flushing?
BEST FIX: Adjust the Chain or Fill Valve. If the toilet starts to flush but then stops, the chain may be too loose (causing the flapper to close prematurely) or the fill valve may be allowing insufficient water into the tank. Here, toilet repairs can be as simple as adjustments made to these components.
How to clear a clogged toilet bowl?
Clearing the clog is super simple, and you probably have a toilet plunger already on hand. Simply insert the plunger into the bowl while it’s still full of water, pressing the mouth of the plunger firmly against the opening at the bottom of the bowl to form a seal.
Why does my toilet pool water?
Pooling water around the base of the toilet is always a cause for concern, and it’s often the result of a leaking wax ring seal. To test if the wax ring has gone bad, squirt some food coloring into the toilet bowl and then flush the toilet.
How far down should the water level be from the top of the overflow valve?
If the water level is lower than one-half inch from the top of the overflow valve, there probably isn’t enough water in the tank to completely flush the toilet, so you should adjust the fill valve to raise the water level, which will provide more water for each flush.
How to get water out of a water tank after flushing?
Some residual water will remain after flushing—be sure to bail it out with a cup or use a wet-type vacuum. Disconnect the water supply valve from the bottom of the tank by twisting the nut loose where the hose meets the tank. If unable to do this by hand, use a crescent wrench.
How many pumps to clean a bathroom?
Don’t be overly enthusiastic; forceful plunging is likely to splash dirty water all over the bathroom. After eight to 10 pumps, lift the plunger away from the bottom of the bowl. If you’ve freed the clog, the water will drain—it usually takes just one or two attempts to free a clog.
