DIY Bicycle Repair Stand
- Step 1: Parts and Tools. The materials and tools necessary to build this repair stand are readily available, easy to...
- Step 2: Building the Base - Step 1. We begin by grabbing the tee fitting and two (2) of the ten (10) inch lengths of...
- Step 3: Building the Base - Step 2. There's your completed stand! Just kidding. That'd be lame. That would...
Full Answer
What is the best bike repair stand?
Bike work stands: A buyer's guide
- 1. The best money-no-object bicycle repair stand: Feedback Sports Sprint Bicycle Repair Workstand In a cycling career full of regrettable purchases, I’ve never regretted spending money on better quality tools. ...
- 2. ...
- 3. ...
- 4. ...
- 5. ...
- 6. ...
- 8. ...
- 9: Great but out of stock: Pedros Folding Repair Stand
How to build a bike repair stand?
How to Make a Bike Repair Stand
- Side Note: About This Bike. This bike is a 1973 Motobecane Le Champion that I've been holding onto for several years, intending to get it back on the ...
- A Closer Look. Here is a look at all of the completed components that make up my bike repair stand clamp apparatus thing.
- It's Like Playing With LEGO. ...
- Dimensions. ...
- Finish Clamp Arms. ...
- Make a Knob. ...
How to build your own bike stand?
7 Awesome DIY Bike Wheel Truing Stands
- Roger Musson’s Wheel Building Guide. This next wooden truing stand is pretty sweet and elegant to boot. Aaron at AAKT was inspired by Roger Musson’s wheel building ebook.
- Another Wooden Truing Stand. Here’s another wooden truing stand, with multiple photos. ...
- Truing Stand Made of Wood. And yet one more truing stand made of wood. ...
How to make a cheep dirt bike stand?
10 Best Dirt Bike Stands (2020 Update)
- BikeMaster Easy Lift & Lower Stand. The BikeMaster Easy Lift & Lower Stand is my top pick for Lift Stands. ...
- Pit Posse Scissor Floor Jack Lift Table Stand. The Pit Posse Dirt Bike ATV Scissor Floor Jack is at the top end of the lift stand scale. ...
- Risk Racing ATS Adjustable Top Magnetic Motocross/Dirt Bike Stand. ...
How do you make a homemade bike repair stand?
1:144:11How To Build Your Own Bike Work Stand in Just 30 Minutes - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe're going to take our long pipe and screw the connecting elbow to one end so it looks a littleMoreWe're going to take our long pipe and screw the connecting elbow to one end so it looks a little something like this. Next we'll take the 12 inch pipe and screw it into the other end of the elbow.
How do you make a wood bike repair stand?
6:4711:27DIY Bike Repair Stand made out of wood - One 2x4 and one 4x4YouTubeStart of suggested clipEnd of suggested clipEnough now put some boards across here. I cut two 14 piece or 14 inch pieces. Too by far. So gotMoreEnough now put some boards across here. I cut two 14 piece or 14 inch pieces. Too by far. So got this whole thing up susana put two boards which are gonna just hold the seat.
What can I use as a bike repair stand?
9:1711:12How to use a bicycle repair stand and what features to look for - YouTubeYouTubeStart of suggested clipEnd of suggested clipI like to do it with the bike on the ground. And then just take an old toe strap or a velcro strapMoreI like to do it with the bike on the ground. And then just take an old toe strap or a velcro strap or something and tie the back wheel and tire assembly to the side of the repair.
Is it worth getting a bike repair stand?
You don't absolutely need a bike repair stand to take care of the most basic maintenance—lubing your chain, swapping tires—but once you start adjusting your own derailleurs or messing around with cables, having a way to adjust your bike while its wheels are off the ground is crucial.
How do you make a 2x4 bike stand?
0:257:09How to Build a Wood Bike Stand! - YouTubeYouTubeStart of suggested clipEnd of suggested clipAlright guys start out you're going to need a 2x4 that is roughly. Three or four feet long and you'MoreAlright guys start out you're going to need a 2x4 that is roughly. Three or four feet long and you're going to need a piece of two by six that's roughly.
How do you make a bike stand?
0:003:39How To Make A Bike Repair Stand DIY - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's one quarter inch and it is screwed to the base. With nuts on the backside which your counterMoreIt's one quarter inch and it is screwed to the base. With nuts on the backside which your counter sunk into the wood. This is what the bolts look like on the bottom side for the hold the flame.
How do you make a PVC bike Stand?
0:267:36DIY PVC Bike Rack - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou will need about 45. Feet of three-quarter inch PVC pipe. This is typically sold in 10-footMoreYou will need about 45. Feet of three-quarter inch PVC pipe. This is typically sold in 10-foot sections. Although I asked an employee at the hardware store to cut mine in half.
What makes a good bike stand?
Angle adjustment: the ability to change the angle of the clamp is crucial when doing more complex repairs such as bleeding hydraulic brakes. The ideal is a stand that's adjustable, easy to swivel and locks down rigid when wanted – it's a pain when you're trying to do something precise and the whole bike tilts away.
How do you build a vertical bike stand?
1:398:07How To Make A DIY Bike Rack | Hank Builds A Freestanding Bicycle RackYouTubeStart of suggested clipEnd of suggested clipNow general rule to keep it nice and sturdy is having at least a third of the length of the uprightsMoreNow general rule to keep it nice and sturdy is having at least a third of the length of the uprights. With this this frame it's gonna need to be that little bit secure. So I've got my sorrel.
Where do you clamp a bike stand?
All bicycles, including mountain bikes, should be clamped into your repair-stand by the seatpost.Most bicycle manufacturers do NOT recommend clamping onto the frame.Carbon framed bikes should NEVER be clamped by their frame tubing.
Can I store my bike on a work stand?
Registered. A stand is fine for storing your bike, and pretty helpful when working on it too. Bikes really don't care what they're hanging from.
How do you clamp a carbon frame on a bike stand?
6:467:35Should You Clamp A Carbon Frame In A Work Stand? - YouTubeYouTubeStart of suggested clipEnd of suggested clipBecause that is a particularly strong part and will resist that clamping force of the bike holder.MoreBecause that is a particularly strong part and will resist that clamping force of the bike holder. So just make sure you clamp it on the seat post. And don't ever clamp the frame.
How do you make a wooden bike rack?
0:122:21How To Make A D.I.Y. Bike Rack - D.I.Y. At Bunnings - YouTubeYouTubeStart of suggested clipEnd of suggested clipDown your timber nice and tight cut off your taper on both ends. And continue on for all six pieces.MoreDown your timber nice and tight cut off your taper on both ends. And continue on for all six pieces. Remove any of the burrs or rough edges giving it a light sand.
How do you make a homemade mountain bike stand?
0:029:01How to Make a Simple Wooden Bicycle Mountain Bike StandYouTubeStart of suggested clipEnd of suggested clipStraight keep it all in line. So that in the end I went for 14 inches for the bottom pieces. And 20MoreStraight keep it all in line. So that in the end I went for 14 inches for the bottom pieces. And 20 inches for the top two pieces and that will depend on the size of your wheel I have a 26 inch wheel.
How do you make a PVC bike Stand?
0:267:36DIY PVC Bike Rack - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou will need about 45. Feet of three-quarter inch PVC pipe. This is typically sold in 10-footMoreYou will need about 45. Feet of three-quarter inch PVC pipe. This is typically sold in 10-foot sections. Although I asked an employee at the hardware store to cut mine in half.
How do you use a mountain bike without a stand?
Just hang the front of the seat on any convenient "peg", or rig hooks or a rope to suspend the bike from. All you need to do is somehow get the rear wheel off the ground while having the pedals clear to turn.
What is the support arm for a clamp?
The support arm that holds the clamp was made from a piece of 1 3/4" by 1/4" thick angle iron, a scrap piece of metal tubing, and a pair of washers.
How to make a carriage bolt pivot?
The holes on the top and bottom pieces for the carriage bolt were drilled using a drill press, and then enlarged using a rotary tool with a small carbide grinding bit. The hole in the upper arm was elongated so the carriage bolt could pivot and remain at 90 degrees to the top arm in any position. The lower hole was made square-ish to keep the carriage bolt from spinning, and the front edge of the carriage bolt was trimmed off (shown in a later step), which allows the bolt to pivot front-to-back as needed.
Where is the main clamp mechanism on a golf ball?
The main clamp mechanism swivels within the support arm and can be locked in position using the threaded golf ball handle on the back end.
Is a vise stand a stand?
Well, technically it's not a stand; it's more of a bicycle clamp-arm-apparatus-thing, which is held in my portable vise stand to use.
Can you add weights to a vise stand?
In my case, this option seemed the most useful as it takes advantage of a heavy tripod base I already have in my shop. Extra weights can be added to the vise stand for more stability if needed.
Step 1: Parts and Tools
The materials and tools necessary to build this repair stand are readily available, easy to work with, and best of all, pretty inexpensive.
Step 2: Building the Base - Step 1
We begin by grabbing the tee fitting and two (2) of the ten (10) inch lengths of pipe. Screw the lengths of pipe into each side of the tee so the pieces are in line either each other (as opposed to perpendicular to each other - relax, you have a 50 percent shot at getting this right...there's really only one way to do it).
Step 3: Building the Base - Step 2
That's it! There's your completed stand! Just kidding. That'd be lame. That would also mean each piece cost about ten dollars. A bit of a ripoff if you ask me. Grab the two (2) 18" lengths of pipe and two (2) 90 degree elbows. Thread and hand tighten an elbow onto the end of one of the lengths of pipe.
Step 4: Build the Base - Step 3
It's time to put the base components together. Obtain the piece from Build the Base - Step 1. Onto one end, thread one of the pieces you made in BtB - Step 2. Now you should have what looks like an "L". Do the same with the other piece from Step 2, but do it on the other end.
Step 5: Up We Go! - Install the Vertical Pole
What's that extra port on the tee, you ask? That's for the big 60" length of pipe. This guy is responsible for bringing your bike to eye level, provided you are somewhere between five and seven feet tall. But hey, if you're not, they make different lengths of pipe, so get the length that best suits your hight.
Step 6: Ummm...Add the Other Thing!
We will now add the arm that will hold the clamp that will hold the bike. You should have, in terms of pipes and pipe fittings, one (1) 10" length of pipe and one (1) 90 degree elbow. Thread the pipe into the elbow.
Step 7: Clamp the Clamp
Grab your two hose clamps and the spring clamp. Slide the two hose clamps onto the 10" piece up top and slap the spring clamp on the top "side" of the horizontal pipe. Don't let go. The clamp will fall. Gravity works. Slide the two hose clamps over the lower handle of the spring clamp and tighten said hose clamps with all your might.
Step 1: Materials and Tools
10' length of 1 1/2" EMT (electrical metallic tubing) - $12.45 from Home Depot electrical dept.
Step 2: Clamping Mechanism
The clamping mechanism consists of modified locking pliers welded to the 1" steel pipe section. Steel pipe was selected due to its stiffness.
Step 3: Rotating Clamp Mechanism Support
The support for the clamp mechanism allows the clamp to rotate 360 deg. The 1" steel clamp pipe fits loosely into the 1 1/4" EMT. I cut a 4" length of 1 1/4" EMT to hold the clamp pipe. I cut a slot down the length of the 4" long EMT with a cut-of blade in the angle grinder and then made the slot a little wider.
Step 4: Base Stand
The base stand is made of 1 1/2" EMT. I cut a length about 4' long for the base post. and drilled (5) 3/8" holes about 3" apart near the top of the post. The holes allow for height adjustment of the clamp support post. I then cut two other pieces about 30" long for legs. The two legs project to the front at about 45 degrees on each side.
Step 5: Ready for Paint
I ran into some issues during painting due to cold, humid weather, so am posting the almost finished pictures for now. As you can see in the photos, the repair stand works for holding the bike by the top tube as well as by the seat tube.
Step 6: Final
Painted the whole thing blue. After paint I added the 3M heavy-duty double sided tape to each side of the clamp angles and adhered the rubber pads. I cut the pads so that they slightly overhang each edge of the angles. You can see how the placement of the T-handle bolts and the addition of the 1" steel spacer help the handles from interfering with each other and the side of the clamp support. All done.
How to attach a jug to a vertical pipe?
Cut the bottom from a sturdy plastic jug and use a hose clamp to attach it to the vertical pipe for use as a small parts tray.
How to make a flange for a sandbox?
Step 1 – Position the flange near a corner of the plywood square, one inch from each edge. With a pencil, mark the four holes. Step 2 – With the 1/4″ bit, drill two of the holes for the flange. Temporarily insert two of the bolts and the flange. This will allow you to accurately drill the other two holes.
Can you cut a vertical notch in a wooden block?
The stand will work okay as it is, but it’s not a bad idea to cut a vertical v-notch or circular impression into the face of each of the wooden blocks. This will help keep the seatpost from tilting while also not needing the clamp as tight. A v-notch can be cut with a miter saw, or a hole saw can be used to make a seatpost-sized vertical hole. Either way, you should still cover it with padding and Gorilla tape as described above.
How to fit a bike on a stand?
To fit your bike on the stand, you need to use a pony clamp. This should be installed at the end of the pipes per the instructions provided. When the clamp is in place, you should place two wooden blocks in the jaws and tighten the clamp.
What happens if you don't have a bike stand?
If you do not have a bike stand, you are making your life harder. Trying to repair or clean your bike without a stand can be a nightmare. The problem is that bike stands can be very expensive and you can feel overwhelmed when trying to choose one. If none of the stands on the market appeal to you, you can always make your own.
How to tighten hex nuts on bike stand?
Using a wrench and socket, you can tighten hex nuts on the protruding bolts. To fit your bike on the stand, you need to use a pony clamp. This should be installed at the end of the pipes per the instructions provided. When the clamp is in place, you should place two wooden blocks in the jaws and tighten the clamp.
What kind of pipes do you use for a bike stand?
If you want a metal bike stand, you should use threaded pipes. There are a few designs that you can try, but there is one that will be fast and inexpensive to complete.
How many bolts to install on a pipe?
You can now install four ¼” bolts with flat washers and install the pipe assembly over the bolts. When you install the pipes, you need to ensure the cross pipe points at the opposite corner of the plywood. You should then tighten all the pipe joints then fix everything in place. Using a wrench and socket, you can tighten hex nuts on the protruding bolts.
How to stop a bike from rocking?
Once the base and legs are set, you need to put end-caps on the ends of the base to stop it rocking. You can then assemble the support tubes and the rests for the bike. You will need a 16” length of 1 ½” diameter pipe that you attach to the cross fitting with the bike rest on it. This fitting also needs to be attached to the legs of the frame. The other rest will be placed on the other end of the 16” pipe.
How many lengths of pipe do you need for a stand?
After the rests have been made, you will turn to the legs and base of the stand. For the legs, you need two 34” lengths of 1 ½” diameter pipe. These pipes will need to be placed in T-fittings. If the fit is correct, you can cement the pieces together.
How to Build a DIY Bicycle Repair Stand
You can build your own DIY bicycle repair stand with, a few lengths of gal pipe, and some t-piece and right angle joiners from the local hardware store. It’s pretty easy to make your own repair stand for carrying out bicycle maintenance.
Materials To Build Your – DIY Bicycle Repair Stand
This DIY Bike Repair Stand is probably the easiest we’ve come across. The items you’ll need to buy (or acquire) are …
