Cut Out the Damaged Area
- Using a carpenter’s square and a pencil or marker, draw a line at least an inch or more above and below the damaged area.
- Use a stud finder to find the nearest stud on either side of the hole and mark those.
- Use a drywall saw to cut along the lines you just drew until you reach the wall studs.
Full Answer
How to fix a large hole in your drywall?
Method 2 Method 2 of 2: Patching with a New Piece of Drywall Download Article
- Cut the hole into a neat square or rectangle. Home Improvement Specialist Expert Interview. ...
- Create a patch out of drywall that is 2 in (5.1 cm) taller than the hole. ...
- Put a screw through the middle of the patch to make a handle. ...
- Apply construction adhesive to the bottom and top edges of the patch. ...
What is the best tool to remove drywall?
Top 15 Best Drywall Cutting Tools Review in 2021
- Best DEWALT Rotary Saw Tool For Cutting Drywall. For every DIYers and renovation workers, we cannot forget Dewalt tools. ...
- Makita Lithium-Ion Cordless Cut-Out Tool. Even with the battery, the tool is very lightweight. ...
- Milwaukee- Fastback II Flip Utility Knife. ...
- DEWALT Max Drywall Cut-Out Tool. ...
- Milwaukee Cordless Cutting Saw For Cutting Drywall. ...
How to cut drywall like a pro?
Tools are Expected to be Cut drywall
- Estimating tape
- Utility knife
- Straight edge
- Drywall saw
- Drywall keyhole saw
- Drywall scratch or sanding square
- Drywall rasp
- Sheetrock saws
- Drywall tee square
- Drywall router
How do you fill holes in drywall?
- Clean hole with blade knife. Cut at an angle so the exterior of the hole is bigger than the interior.
- Fill the hole with painter's putty.
- Let it dry.
- Spackle over the putty.
- For medium holes, use a drywall metal patch.
- Sand the surface smooth around the hole.
- Wipe off dust.
- Peel paper backing off the patch.
How do you cut and fix drywall?
0:553:05How to Cut and Repair Drywall | The Home Depot - YouTubeYouTubeStart of suggested clipEnd of suggested clipMove slowly along the outline letting the blade do most of the work. So your cut is clean andMoreMove slowly along the outline letting the blade do most of the work. So your cut is clean and straight then carefully remove the damaged section of the drywall. Next measure the new wall opening.
What is the best way to cut a hole in drywall?
You'll be surprised how accurate you can make it. Then cut the hole with a drywall saw (Photo 3). It's best to slightly angle the saw so the opening in the back is larger than in the front. That way the box will slip into the opening easier.
How do you repair a hole in a piece of drywall?
5:2815:38How to Fix Holes in Drywall - 4 Easy Methods - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse your knife to score a line all the way down one side and all the way down the inside that's justMoreUse your knife to score a line all the way down one side and all the way down the inside that's just a little bit smaller than the hole. Now we're going to flip it to the other side for the height.
What tool do you use to cut drywall?
utility knifeThe Razor Knife The most commonly used tool for cutting drywall is the razor or utility knife. You score the panel, apply some pressure, and snap! You've got a new, clean edge.
How do you cut drywall without a saw?
0:312:10How To Cut Drywall or Sheetrock With A Knife. Cutting Sheet Rock hacks.YouTubeStart of suggested clipEnd of suggested clipAnd all I got to do is just a little bit of pressure just to cut through that first layer of paperMoreAnd all I got to do is just a little bit of pressure just to cut through that first layer of paper on the drywall. Just take your time go slow just to get a nice.
What is the fastest way to fix a hole in the wall?
0:211:48How To Fix a Hole in the Wall - YouTubeYouTubeStart of suggested clipEnd of suggested clipThese plaster patches are super easy to attach. You simply peel off the back and stick it onto theMoreThese plaster patches are super easy to attach. You simply peel off the back and stick it onto the wall. Just smooth down the edges even grab your spatula to make sure it's really smooth.
What's the difference in sheetrock and drywall?
Drywall is a flat panel made of gypsum plaster sandwiched in between two sheets of thick paper. It adheres to metal or wood studs using nails or screws. Sheetrock is a specific brand of drywall sheet. These terms are often used interchangeably.
What is the fastest way to fix a small hole in the wall?
0:145:00How to patch a hole in your wall - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo right now what we're going to do is we're going to open up the small amount of spackle that weMoreSo right now what we're going to do is we're going to open up the small amount of spackle that we have and an inch and a half will fit nicely into this container.
What to use to cut a circle in drywall?
0:211:39How to Cut Circular Holes in Drywall Video - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce we've completed our circle. We can then use a drywall saw to make the cut in the drywall. SoMoreOnce we've completed our circle. We can then use a drywall saw to make the cut in the drywall. So what I'm using here is a drywall saw or a wall board saw it has a very firm blade.
How do I cut a hole in my wall?
0:132:08Cut Inspection Hole in Wall - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow one advantage to using the bevel cut is that the piece won't fall inside the wall. And if I haveMoreNow one advantage to using the bevel cut is that the piece won't fall inside the wall. And if I have to replace it well the repair job is pretty simple.
Can I use a spade bit on drywall?
While best suited to drilling softwoods, spade bits can also be used on hardwood, chipboard, fibreboard (such as MDF), plasterboard (used in walls), acrylic and plastic-laminated wood. They can be used in drills, for general use, or impact drivers, if drilling holes in tree stumps or thick, tough wood.
How do you cut a perfect square in drywall?
1:308:33How to Cut Drywall EFFICIENTLY! - YouTubeYouTubeStart of suggested clipEnd of suggested clipGet your knife in position find that little puncture you just made and then what you do is you pinchMoreGet your knife in position find that little puncture you just made and then what you do is you pinch your blade. And so I've got my finger resting.
Measure for the Cut
Drywall doesn’t have to be installed perfectly tight in the corner of a room to properly finish it. To account for walls that may be slightly out of plumb, we subtract about 1/8 inch when making our measurements from a corner wall.
Cut the Drywall
To prevent the drywall paper from tearing when you cut it, it’s important to score it with a utility knife. Score your markings on the outside of the line, that way your hole doesn’t end up too small.
Install the Drywall
If you’ve used these basic steps and measured correctly, the hole should line up with the receptacle box. Complete installation by fastening the drywall to the studs with drywall screws.
Small Dents and Dings
Scrape away loose debris from the hole. Cover the hole or dent with fast-drying spackle to bring the spackle level with the drywall surface and let it dry 24 hours -- or the time recommended by the manufacturer’s instructions. Sand smooth.
Popped Nail Heads
A popped nail isn't holding in the stud and backs out of the drywall, creating a popped nail head.
Small Holes
For small holes, like those created by a doorknob, a patch kit may be used.
Large Holes
For holes larger than 6 inches, you'll create a drywall patch with a different attachment method for the repair.
Corner Bead Patch
Corner bead is used where two pieces of drywall meet to form a corner. Corner bead is available in a variety of materials, including metal, paper and vinyl.
Finish the Repair
You're almost done. Here's where you make it look like nothing happened.
Repair Textured Drywall
Textured drywall is a bit more complicated, but still pretty simple to repair.
How to tape a wall with a knife?
Apply a coat of compound and tape to each joint. Thin the compound a bit with water to help embed the tape. Smooth the tape with the 6-in. knife, pulling out from the center toward each end. Squeeze some, but not all, of the compound out from under the tape so you don’t create a big hump on the wall. Immediately apply a light coating to the topside of the tape, tapering it out onto the wall.
Why do drywall screws pop up?
But drywall screws sometimes pop up too, as a result of damp framing that dries out and shrinks during the first year or two in new construction. The first step of how to patch a small hole in the wall is to drive nails back down using a nail set.
Can you use a second coat of compound on drywall?
And you can apply a second coat of compound as soon as the first hardens. You don't have to wait for it to dry completely as you complete a how to fix drywall project.
