how to make a bike repair stand

^{DIY Bicycle Repair Stand}

1. Parts and Tools. The materials and tools necessary to build this repair stand are readily available, easy to work with, and best of all, pretty inexpensive.
2. Building the Base - Step 1. We begin by grabbing the tee fitting and two (2) of the ten (10) inch lengths of pipe. ...
3. Building the Base - Step 2. There's your completed stand! Just kidding. That'd be lame. That would also mean each piece cost about ten dollars.
4. Build the Base - Step 3. It's time to put the base components together. Obtain the piece from Build the Base - Step 1. ...
Up We Go! - Install the Vertical Pole. What's that extra port on the tee, you ask? That's for the big 60" length of pipe. ...
Ummm...Add the Other Thing! We will now add the arm that will hold the clamp that will hold the bike. ...
Clamp the Clamp. Grab your two hose clamps and the spring clamp. ...
Voila! Throw Your Bike Up There! If you are certain all joints that have rotational stress on them are tight (this would include the lower tee and two ...
Improvements. As with any project, this is version 1.0. There are some improvements that could definitely do some good.

Full Answer

What is the best bike repair stand?

Bike work stands: A buyer's guide

• 1. The best money-no-object bicycle repair stand: Feedback Sports Sprint Bicycle Repair Workstand In a cycling career full of regrettable purchases, I’ve never regretted spending money on better quality tools. ...
• 2. ...
• 3. ...
• 4. ...
• 5. ...
• 6. ...
• 8. ...
• 9: Great but out of stock: Pedros Folding Repair Stand

How to build a bike repair stand?

How to Make a Bike Repair Stand

1. Side Note: About This Bike. This bike is a 1973 Motobecane Le Champion that I've been holding onto for several years, intending to get it back on the ...
2. A Closer Look. Here is a look at all of the completed components that make up my bike repair stand clamp apparatus thing.
3. It's Like Playing With LEGO. ...
4. Dimensions. ...
5. Finish Clamp Arms. ...
6. Make a Knob. ...

More items...

How to build your own bike stand?

7 Awesome DIY Bike Wheel Truing Stands

• Roger Musson’s Wheel Building Guide. This next wooden truing stand is pretty sweet and elegant to boot. Aaron at AAKT was inspired by Roger Musson’s wheel building ebook.
• Another Wooden Truing Stand. Here’s another wooden truing stand, with multiple photos. ...
• Truing Stand Made of Wood. And yet one more truing stand made of wood. ...

How to make a cheep dirt bike stand?

10 Best Dirt Bike Stands (2020 Update)

1. BikeMaster Easy Lift & Lower Stand. The BikeMaster Easy Lift & Lower Stand is my top pick for Lift Stands. ...
2. Pit Posse Scissor Floor Jack Lift Table Stand. The Pit Posse Dirt Bike ATV Scissor Floor Jack is at the top end of the lift stand scale. ...
3. Risk Racing ATS Adjustable Top Magnetic Motocross/Dirt Bike Stand. ...

More items...

How do you make a homemade bike repair stand?

1:144:11How To Build Your Own Bike Work Stand in Just 30 Minutes - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe're going to take our long pipe and screw the connecting elbow to one end so it looks a littleMoreWe're going to take our long pipe and screw the connecting elbow to one end so it looks a little something like this. Next we'll take the 12 inch pipe and screw it into the other end of the elbow.

What can I use as a bike repair stand?

9:1711:12How to use a bicycle repair stand and what features to look for - YouTubeYouTubeStart of suggested clipEnd of suggested clipI like to do it with the bike on the ground. And then just take an old toe strap or a velcro strapMoreI like to do it with the bike on the ground. And then just take an old toe strap or a velcro strap or something and tie the back wheel and tire assembly to the side of the repair.

How do you make a wood bike repair stand?

6:4711:27DIY Bike Repair Stand made out of wood - One 2x4 and one 4x4YouTubeStart of suggested clipEnd of suggested clipEnough now put some boards across here. I cut two 14 piece or 14 inch pieces. Too by far. So gotMoreEnough now put some boards across here. I cut two 14 piece or 14 inch pieces. Too by far. So got this whole thing up susana put two boards which are gonna just hold the seat.

How do you make a bike repair stand out of PVC pipe?

0:439:26Build This PVC Bike Stand Cheap! - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo today we are going to build a bike stand first you're going to need a half stick of two inchMoreSo today we are going to build a bike stand first you're going to need a half stick of two inch schedule 40 PVC pipe.

How do you make a bike stand?

0:003:39How To Make A Bike Repair Stand DIY - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's one quarter inch and it is screwed to the base. With nuts on the backside which your counterMoreIt's one quarter inch and it is screwed to the base. With nuts on the backside which your counter sunk into the wood. This is what the bolts look like on the bottom side for the hold the flame.

How do you make a 2x4 bike stand?

0:257:09How to Build a Wood Bike Stand! - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd basically I'm gonna take my two 16-inch blocks. And place something on each side of the tire.MoreAnd basically I'm gonna take my two 16-inch blocks. And place something on each side of the tire. Now what you want to do is give enough room so that's the tire sitting flat.

How do you make a wooden bike rack?

0:122:21How To Make A D.I.Y. Bike Rack - D.I.Y. At Bunnings - YouTubeYouTubeStart of suggested clipEnd of suggested clipDown your timber nice and tight cut off your taper on both ends. And continue on for all six pieces.MoreDown your timber nice and tight cut off your taper on both ends. And continue on for all six pieces. Remove any of the burrs or rough edges giving it a light sand.

How do you make a bike storage rack?

1:006:03DIY Bike Rack for $20 / Bike Storage Stand & Cabinet for GarageYouTubeStart of suggested clipEnd of suggested clipThe upper 2x4 should be placed at 14 inches above the lower 2x4. Your hook placement should beMoreThe upper 2x4 should be placed at 14 inches above the lower 2x4. Your hook placement should be roughly 24 inches from the next hook on the same row.

How do you make a road bike stand?

0:597:50How To Build A Bike Stand | Easy DIY Road Bike Storage - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's actually going to work by holding each individual wheel in place so the bike doesn't fall overMoreIt's actually going to work by holding each individual wheel in place so the bike doesn't fall over so for this I'm gonna need six individual bits to help that rack start to work.

How do you make a bike trainer?

DIY Turbo Trainer If you're making one of these yourself the simplest method is to build a stand out of timber then fit BMX-style pegs to either side of your rear axle. The pegs will sit in notches at the top of your timber stand, supporting the rear wheel, and you can then pedal away to your heart's content.

How do you build a vertical bike stand?

1:398:07How To Make A DIY Bike Rack | Hank Builds A Freestanding Bicycle RackYouTubeStart of suggested clipEnd of suggested clipNow general rule to keep it nice and sturdy is having at least a third of the length of the uprightsMoreNow general rule to keep it nice and sturdy is having at least a third of the length of the uprights. With this this frame it's gonna need to be that little bit secure. So I've got my sorrel.

How do you make a road bike stand?

0:597:50How To Build A Bike Stand | Easy DIY Road Bike Storage - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's actually going to work by holding each individual wheel in place so the bike doesn't fall overMoreIt's actually going to work by holding each individual wheel in place so the bike doesn't fall over so for this I'm gonna need six individual bits to help that rack start to work.

How do you make a motorcycle stand?

0:036:47Build a Wooden Dirt Bike Stand // Inexpensive & Bullet Proof! - YouTubeYouTubeStart of suggested clipEnd of suggested clipOn here to raise the bike for the wintertime. So we'll build one for this bike I'll show you how toMoreOn here to raise the bike for the wintertime. So we'll build one for this bike I'll show you how to build wooden motorcycle stand for this bike.

How do you make a dirt bike stand?

0:506:13How to Make a Dirt Bike Stand - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd two piece this cut at six inches. So I'm gonna do that all here and can be very simple just makeMoreAnd two piece this cut at six inches. So I'm gonna do that all here and can be very simple just make sure you square up your bling.

Step 1: Parts and Tools

The materials and tools necessary to build this repair stand are readily available, easy to work with, and best of all, pretty inexpensive.

Step 2: Building the Base - Step 1

We begin by grabbing the tee fitting and two (2) of the ten (10) inch lengths of pipe. Screw the lengths of pipe into each side of the tee so the pieces are in line either each other (as opposed to perpendicular to each other - relax, you have a 50 percent shot at getting this right...there's really only one way to do it).

Step 3: Building the Base - Step 2

That's it! There's your completed stand! Just kidding. That'd be lame. That would also mean each piece cost about ten dollars. A bit of a ripoff if you ask me. Grab the two (2) 18" lengths of pipe and two (2) 90 degree elbows. Thread and hand tighten an elbow onto the end of one of the lengths of pipe.

Step 4: Build the Base - Step 3

It's time to put the base components together. Obtain the piece from Build the Base - Step 1. Onto one end, thread one of the pieces you made in BtB - Step 2. Now you should have what looks like an "L". Do the same with the other piece from Step 2, but do it on the other end.

Step 5: Up We Go! - Install the Vertical Pole

What's that extra port on the tee, you ask? That's for the big 60" length of pipe. This guy is responsible for bringing your bike to eye level, provided you are somewhere between five and seven feet tall. But hey, if you're not, they make different lengths of pipe, so get the length that best suits your hight.

Step 6: Ummm...Add the Other Thing!

We will now add the arm that will hold the clamp that will hold the bike. You should have, in terms of pipes and pipe fittings, one (1) 10" length of pipe and one (1) 90 degree elbow. Thread the pipe into the elbow.

Step 7: Clamp the Clamp

Grab your two hose clamps and the spring clamp. Slide the two hose clamps onto the 10" piece up top and slap the spring clamp on the top "side" of the horizontal pipe. Don't let go. The clamp will fall. Gravity works. Slide the two hose clamps over the lower handle of the spring clamp and tighten said hose clamps with all your might.

Step 1: Side Note: About This Bike

This bike is a 1973 Motobecane Le Champion that I've been holding onto for several years, intending to get it back on the road at some point.

Step 2: A Closer Look

Here is a look at all of the completed components that make up my bike repair stand clamp apparatus thing.

Step 3: It's Like Playing With LEGO

A similarly functioning apparatus could be made in any number of ways, depending on what things a person has to work with.

Step 5: Finish Clamp Arms

The clamp arms were cleaned with a wire wheel in a power drill to remove all the paint and rust.

Step 7: Modify Carriage Bolt

In order for the carriage bolt to pivot as needed, I trimmed off one side of the head as shown using an angle grinder.

Step 8: Add Pads

Some scrap pieces of rubber from a floor mat were cut to size as needed.

Step 9: Support Arm

The support arm that holds the clamp was made from a piece of 1 3/4" by 1/4" thick angle iron, a scrap piece of metal tubing, and a pair of washers.

Step 1: Materials and Tools

10' length of 1 1/2" EMT (electrical metallic tubing) - $12.45 from Home Depot electrical dept.

Step 2: Clamping Mechanism

The clamping mechanism consists of modified locking pliers welded to the 1" steel pipe section. Steel pipe was selected due to its stiffness.

Step 3: Rotating Clamp Mechanism Support

The support for the clamp mechanism allows the clamp to rotate 360 deg. The 1" steel clamp pipe fits loosely into the 1 1/4" EMT. I cut a 4" length of 1 1/4" EMT to hold the clamp pipe. I cut a slot down the length of the 4" long EMT with a cut-of blade in the angle grinder and then made the slot a little wider.

Step 4: Base Stand

The base stand is made of 1 1/2" EMT. I cut a length about 4' long for the base post. and drilled (5) 3/8" holes about 3" apart near the top of the post. The holes allow for height adjustment of the clamp support post. I then cut two other pieces about 30" long for legs. The two legs project to the front at about 45 degrees on each side.

Step 5: Ready for Paint

I ran into some issues during painting due to cold, humid weather, so am posting the almost finished pictures for now. As you can see in the photos, the repair stand works for holding the bike by the top tube as well as by the seat tube.

Step 6: Final

Painted the whole thing blue. After paint I added the 3M heavy-duty double sided tape to each side of the clamp angles and adhered the rubber pads. I cut the pads so that they slightly overhang each edge of the angles. You can see how the placement of the T-handle bolts and the addition of the 1" steel spacer help the handles from interfering with each other and the side of the clamp support. All done.

How to Build a DIY Bicycle Repair Stand

You can build your own DIY bicycle repair stand with, a few lengths of gal pipe, and some t-piece and right angle joiners from the local hardware store. It’s pretty easy to make your own repair stand for carrying out bicycle maintenance.

Materials To Build Your – DIY Bicycle Repair Stand

This DIY Bike Repair Stand is probably the easiest we’ve come across. The items you’ll need to buy (or acquire) are …

How long to let a X-ray machine sit?

Hold the parts together for at least 30 seconds more. Then let the cemented assembly sit for at least 2 hours. After at least 2 hours, you will lay the X down on the work surface & sprinkle some of the PVC shavings into the gap in the crotch of the X on one side. Then dribble a small amount of cement into the shavings.

What tools are needed to cut PVC pipe?

There is also some shaping of some of the pipe & fittings, so some carving & shaping tools are required. Tools: - hack saw ( or alternately a P VC tubing cutter) - tape measure. - wood chisel (or alternately a dremel tool with a carbide bit) - pencil & dry-erase marker. - file. - sand paper.

Can you use a level on a stand?

You can use a level to make sure (as long as you are sure you are working on a flat level surface). Once you are satisfied that the stand is perfectly upright & the base is stable with no rocking, you should put alignment marks in the upright portion of the T-fittings & the 34" legs near the T-fittings.

Can you dribble cement into a fitting?

You can also coat the other parts of the cemented joint with another coat of cement to make sure it is strong. Just be certain not to dribble cement into the branches of the fitting that will later need to have pipe inserted. Now you're done with the most tedious & time-consuming part of the build.