
Opening the cabinet of Maytag (including Atlantis) models Note: Disconnect the power source to your dryer before you begin to open its cabinet. Either unplug the unit from the wall outlet, remove the appropriate fuse from the fuse box, or flip the appropriate breaker in your home's circuit breaker panel.
How to troubleshoot why a Maytag dryer is not working?
Maytag Dryer Won’t Start – Troubleshoot and Diagnosis
- Incoming Power Problem. If your Maytag dryer is not turning on, the first step is to check power. ...
- Incorrect Dryer Settings. If your Maytag dryer lights up yet will not start, first check your settings. ...
- Door Not Latched Properly. ...
- Blown Thermal Fuse. ...
- Defective Dryer Start Switch. ...
- Bad Belt Switch. ...
- Faulty Drive Motor. ...
How do you open a Maytag washer to repair it?
How to Take the Top Off a Maytag Washer
- Safety First. Remember that these appliances conduct electrical currents. ...
- Lower-Front Screws. As you go through this process, you will see that it is largely about removing screws. ...
- Front Panel. ...
- Lifting the Front Edge. ...
- Machine Bolts. ...
- Returning Everything. ...
How to take apart a Maytag dryer?
How to Take Apart a Maytag Bravos Dryer. Unplug the electrical cord of the Maytag Bravos dryer from the electrical outlet before taking the dryer apart. Locate the screws on the bottom of the front panel and unfasten the screws with a screwdriver, lifting the panel up from the bottom and detaching it from the clips on the top of the panel.
How to replace a Maytag electric dryer thermal fuse?
These simple steps summarize the process below:
- Unplug your dryer and ensure it is no longer connected to the gas or electric.
- Locate the thermal fuse, as above.
- Disconnect the thermal fuse from the wires.
- Test the fuse with a multimeter.
- If the needle on your multimeter does not move, your thermal fuse is blow.

How do you take apart an old Maytag dryer?
3:225:57Maytag Dryer - How to Take Apart a Dependable Care Dryer - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow before we take this completely off we have two quarter inch screws right here those up frontMoreNow before we take this completely off we have two quarter inch screws right here those up front onto the lint filter assembly. We'll take those.
How do I open up my dryer?
2:037:35How To: Disassemble Whirlpool/Kenmore Dryer - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt out once you pop it off there's going to be two door springs one on each side if you have thoseMoreIt out once you pop it off there's going to be two door springs one on each side if you have those take them off and then on the bottom of the big panel.
How do you open a dryer cover?
0:592:03How to Open the Top Of a Clothes Dryer - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you just push it in and twist. And it'll pop one side up push it in with an indentation twist.MoreAnd you just push it in and twist. And it'll pop one side up push it in with an indentation twist.
How do I remove the panel from my Maytag dryer?
The front panel of the Maytag clothes dryer is shaped like a goal post. Grasp the skinny, upper sides and wiggle them back and forth to unclip the panel. Pull the skinny ends of the front panel toward you, lifting it off the bottom clips.
How do you open the top of a Maytag dryer?
0:422:34How to Open a Dryer Cover (Maytag) for Repairs - YouTubeYouTubeStart of suggested clipEnd of suggested clipUp you're gonna lift this I'm sorry now if you pop. The after popping the two side clips. Off youMoreUp you're gonna lift this I'm sorry now if you pop. The after popping the two side clips. Off you simply lift up down below.
How do you open a Maytag Centennial dryer?
0:482:58Maytag centennial MGDC555DW2 commercial technology dryer front ...YouTubeStart of suggested clipEnd of suggested clipAnd under this corner and the corner over there are little clips that if you slide it forward justMoreAnd under this corner and the corner over there are little clips that if you slide it forward just enough they'll pop up and I'll do it and I'll show you what we did. Ok.
How do you remove the front panel of a dryer?
Insert a flat-head screwdriver or putty knife into the gap between the upper and lower front panel of the dryer. Depress the two spring clips to release the lower dryer panel. Remove the lower panel.
How do you take the back off a Maytag Bravos dryer?
Take the drum out of the Maytag Bravos dryer by placing one hand on the bottom of the drum in the back and one hand on the top in the front , lifting up on the back end to dislodge it from the slot in the rear panel.
How do you remove the front of a Maytag Bravos dryer?
0:442:36Maytag Bravos series dryer - front panel and dryer duct accessYouTubeStart of suggested clipEnd of suggested clipAnd I took a little putty knife and shoved it in there and this lid popped up and this I took aMoreAnd I took a little putty knife and shoved it in there and this lid popped up and this I took a little bit of swearing. And jiggled it and you're able to raise this lid up you have to get the lid up.
How do you open a Maytag 3000 dryer?
1:2920:05Maytag 3000 Series Dryer Not Heating Up - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo get the four screws out of the bottom. And once you get those four screws out in the bottom thisMoreTo get the four screws out of the bottom. And once you get those four screws out in the bottom this panel here just comes down and comes out and see all the dryer mess.
How do you take the front panel off a Maytag front load washer?
0:092:33See how to remove and install the front panel Maytag washer - YouTubeYouTubeStart of suggested clipEnd of suggested clipLoad it down I line it I'm push down on the two bottom corners until the clip snaps in place.MoreLoad it down I line it I'm push down on the two bottom corners until the clip snaps in place.
How to open Maytag dryer cabinet?
How to open the cabinet of Maytag - including Atlantis - brand dryers : Disconnect the power source to your dryer before you begin to open its cabinet. Either unplug the unit from the wall outlet, remove the appropriate fuse from the fuse box, or flip the appropriate breaker in your home's circuit breaker panel.
Where are the screws on an old kitchen cabinet?
Two screws are located at the bottom of the older cabinet's front. One in either corner. Remove both screws and then lift the panel until the clips that are found at the top of the panel disengage. Disconnect the door switch and any other wiring, taking careful note of which wires are to be reconnected where.
Where is the idler arm on a dryer?
Take the shroud cover off the dryer and locate the idler arm and motor at the bottom of the cabinet, moving the idler arm forward to relieve the tension on the belt.
How to unfasten door switch connector?
Tilt the front panel forward and unfasten the door switch connector from the metal prongs on the back of the front panel by hand, setting the panel off to the side.
How to tell what model my dryer is?
You need to tell me the model number. When you open the dryer door, where you load the clothes in, look on the door or that front part of the dryer. It's on a silver or white colored tag.
What parts of a dryer go bad?
Other common parts to go bad are the door switch and the push-to-start switch . All of these can be checked with an ohmmeter, after you unplug the dryer and pull at the wires off of the part being tested. I hope it goes well for you!
Why does my dryer go bad?
The thermal fuse is made to blow when there is (most of the time) a problem with your venting, or lack of proper venting. When the hot air and moisture cannot leave the dryer fast enough through the vent, it heats up in the dryer and then quits. It’s there to keep dryer fires from happening more frequently. It’s not resettable so it’ll get your attention that something is wrong!
Why do dryer sheets cling to towels?
The ‘softeners’ in dryer sheets cling to your towels and reduce their ability to absorb water.
How does air flow in a dryer?
The air in this (normally) closed system flows from the intake port, through the heating elements, and into the drum. It then flows out of the drum through the lint trap, through the fan (which provides the air flow) and out through the vent. When the door is opened, and if the door switch is defeated, the air would take the path of least resistance, the open door. Air flow now would be into the door, through the lint trap, through the fan, and out the vent. There would be virtually zero airflow across the heating elements, and therefore would be virtually zero hot air entering the drum. Assuming the clothes do not fall out, they would take LONGER to dry this way them if you hung them up on a rope in your living room.
How many screws does a front load washer have?
I replaced the water pump on my front-load washer, and all I had to do was take the bottom front panel off to get to it. Four screws is all that holds it on.
Do Maytag rollers go bad?
If you have and OLD school Maytag, it is most likely one of the rollers in the back. While the pads can go bad, they are quite sturdy, and last for long periods of time.
Can you remove the top of a dryer?
You can remove the top, the front, and the back, depending upon what you’re trying to do. Be sure to disconnect the electrical power and, if it is a gas dryer, turn off the gas before doing any repair work.
Can you remove the back of a dryer vent?
Removing the back is trickiest, but not because of the way it is attached (it is just held in place with screws) but because you usually must wrestle the dryer away from the wall and detach the dryer vent before you can do this. Fortunately, however, opening the top and front will suffice for most repairs.
Is a clothes dryer impenetrable?
Although a clothes dryer looks like an almost impenetrable appliance , it is fairly easy to open up to gain access to the working parts for repairs. In fact, because it’s pretty simple once you know how, this is a great way to gain a clearer understanding of how this appliance works.
