Repairing Guides

how to repair a briggs and stratton carburetor

by Anthony Douglas Published 2 years ago Updated 2 years ago
image

Step 1 How to Rebuild a Briggs and Stratton Quantum Engine Carburetor

Carburetor

A carburetor or carburettor is a device that mixes air and fuel for internal combustion engines in the proper air–fuel ratio for combustion. It is sometimes colloquially shortened to carb in the UK and North America or carby in Australia. To carburate or carburet means to mix the air and fu…

Remove the Air filter cover and air filter. This is done by removing the screw at the top of the filter housing, it is a flat head, as well as a 5/16 socket.

Full Answer

How to remove Briggs?

How to remove the blades of a Briggs and Stratton lawnmower, step by step:

  1. Check the operator’s manual
  2. Remove the spark plug and disengage the ignition wire
  3. Remove the fuel from the chamber
  4. Tip the mower and use a cleaner spray
  5. Remove the bolts retaining blade

How to clean and rebuild a Tecumseh carburetor?

How to clean Tecumseh vector carburetor

  • Remove the rubber hose from the carburetor with the help of needle plier. ...
  • Set the carburetor on the top. ...
  • Loose all the three screws to remove the cover of the carburetor. ...
  • Spray the cleaner inside the metal bowl and all its points or nozzles in the carburetor. ...

More items...

How to clean a carburetor without removing it?

You will need these tools to do the job:

  • Aerosol Cleaner: You will need to purchase an aerosol cleaner that is specifically for cleaning electrically charged or fuel-powered machinery. ...
  • Air-compressor Gun: Some points or parts of your carburetor may display a heavy buildup of grease as well as clumps of grass and dirt. ...
  • Flashlight: To inspect your carburetor, you’ll need good light. ...

More items...

How to clean and adjust carburetor?

  • Turn the engine off and remove the air filter, to access the carburetor freely.
  • Turn the idle mixture screw clockwise until the needle touches the throttle plate. ...
  • Repeat the process with the main jet adjustment screw, but turn it counterclockwise by 1 to 1-1/2 turns.

More items...

image

How do you rebuild a small Briggs and Stratton carburetor?

2:078:08Briggs & Stratton Lawn Mower Engine Carburetor Rebuild Kit #498260YouTubeStart of suggested clipEnd of suggested clipDetach the carburetor from the throttle rod. And set it on a sturdy surface use pliers to pull outMoreDetach the carburetor from the throttle rod. And set it on a sturdy surface use pliers to pull out the choke plate and remove the choke arm.

How do you take apart a Briggs and Stratton carburetor?

1:304:54Briggs & Stratton Small Engine Carburetor Replacement Part ...YouTubeStart of suggested clipEnd of suggested clipUse locking pliers to crimp the fuel. Line lift the fuel tank off of the blower housing and useMoreUse locking pliers to crimp the fuel. Line lift the fuel tank off of the blower housing and use pliers to release the spring clamp securing the fuel line detach the line from the carburetor.

Can you clean a Briggs and Stratton carburetor?

2:0114:52Easiest Way To Clean A Metal Briggs Carburetor - YouTubeYouTubeStart of suggested clipEnd of suggested clipEven right where the throttle shaft. Comes down into the body of the carburetor on the top hereMoreEven right where the throttle shaft. Comes down into the body of the carburetor on the top here right there you can spray some in there. And then just start working it back and forth.

How do you adjust the carburetor mixture on a Briggs and Stratton screw?

0:482:12How to Adjust a Briggs & Stratton Carburetor - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe speed control lever to the idle or lowest speed. Moving the lever by hand rotate the carburetorMoreThe speed control lever to the idle or lowest speed. Moving the lever by hand rotate the carburetor adjustment screw with a screwdriver slowly turning it clockwise until you hear the engine slowing.

How do I know if my lawn mower carburetor is bad?

Dirty Carburetor SymptomsThe lawn mower engine has trouble starting.The engine starts but stalls while you're cutting the lawn.The engine runs rough during mowing.Black smoke is seen coming out of the muffler.There is a noticeable increase in fuel consumption during normal lawn mower use.

How do you clean a gummed carburetor?

Make sure the carburetor is cool to the touch before cleaning.Dilute cleaner. ... Clear air filter. ... Remove the carburetor. ... Remove carburetor float. ... Remove other removable components. ... Soak and scrub components. ... Rinse and dry. ... Reassemble and replace.

How to clean grit off carburetor?

Soak metal and plastic carburetor parts in all-purpose parts cleaner for no more than 15 minutes to remove grit. Or, while wearing safety glasses, spray the parts with carburetor cleaner. Then, wipe away solvent and other residue thoroughly using a clean cloth.

How to tighten carburetor with bolts?

Position the carburetor so the beveled edge fits into the fuel intake pipe and attach the carburetor with nuts or bolts, as required, leaving these fasteners loose for final tightening with a torque wrench. Consult your Briggs & Stratton Authorized Dealer for proper tightening torque.

How to use a choke lever on a carburetor?

Insert the choke shaft into the carburetor body and engage the return spring. If the choke lever uses a detent spring to control the choke plate position, guide the spring into the notched slot on the choke lever. Place the choke plate on the shaft with the single notch on the edge toward the fuel inlet. Lift the choke shaft and lever up slightly and turn counterclockwise until the stop on the lever clears the spring anchor. Push the shaft down.

How to remove fuel bowl from carburetor?

Remove the fuel bowl from the carburetor body. The fuel bowl may be attached with either a bolt or the high-speed mixture screw. Push the hinge pin out of the carburetor body with a small pin or pin punch. Take care to tap only the pin to avoid damaging the carburetor body. Remove the float assembly, inlet needle valve and fuel bowl gasket.

How to remove float assembly?

Remove the float assembly, inlet needle valve and fuel bowl gasket. If your carburetor contains an idle mixture screw, remove it along with the spring. Rotate the throttle plate to the closed position, remove the throttle plate screws and the throttle plate. Remove the throttle plate shaft and foam seal.

How to disconnect anti-afterfire solenoid?

Disconnect the device, known as an anti-afterfire solenoid, by removing the wire connector from the solenoid's receptacle. With the carburetor still connected to the governor, unfasten the carburetor mounting bolts. If a connecting pipe joins the carburetor to the engine block, first remove the pipe mounting bolts.

What to do if your engine does not have a fuel valve?

If your engine does not contain a fuel valve, use a fuel line clamp to prevent fuel from draining out of the tank while the carburetor is disconnected from the engine . Some carburetors contain an electrical device at the base of the fuel bowl to control afterfire.

How to clean grit off carburetor?

Soak metal and plastic carburetor parts in all-purpose parts cleaner for no more than 15 minutes to remove grit. Or, while wearing safety glasses, spray the parts with carburetor cleaner. Then, wipe away solvent and other residue thoroughly using a clean cloth.

How to get rid of stubborn grit on carburetor?

Inspect all components and use additional carburetor cleaner to loosen stubborn grit and to clear obstructions

How to remove float assembly?

Remove the float assembly, inlet needle valve and fuel bowl gasket . If your carburetor contains an idle mixture screw, remove it along with the spring. Rotate the throttle plate to the closed position, remove the throttle plate screws and the throttle plate. Remove the throttle plate shaft and foam seal. Then, remove the choke plate and choke shaft ...

How to use a choke lever on a carburetor?

Insert the choke shaft into the carburetor body and engage the return spring. If the choke lever uses a detent spring to control the choke plate position, guide the spring into the notched slot on the choke lever. Place the choke plate on the shaft with the single notch on the edge toward the fuel inlet. Lift the choke shaft and lever up slightly and turn counterclockwise until the stop on the lever clears the spring anchor. Push the shaft down

How to disconnect carburetor from engine block?

If a connecting pipe joins the carburetor to the engine block, first remove the pipe mounting bolts. Then, disconnect the carburetor from the pipe by removing the nuts and sliding the carburetor off the studs. Sketch the governor spring positions before disconnecting them to simplify reattachment

How to remove spark plug from air cleaner?

Disconnect the spark plug lead and secure it away from the spark plug. Then, remove the air cleaner assembly

How to tighten carburetor with bolts?

Position the carburetor so the beveled edge fits into the fuel intake pipe and attach the carburetor with nuts or bolts, as required, leaving these fasteners loose for final tightening with a torque wrench. Consult your Briggs & Stratton Authorized Dealer for the proper tightening torque

Briggs and Stratton Carburetor Troubleshooting

Briggs and Stratton’s engines are made with 3 types of carburetors. They can be made with a primer system, choke system, and auto-choke system. Whenever you are facing any kind of issues with your carburetor, make sure to check the model. The number is stamped in the engine or printed in the label engine or the valve cover.

Frequently Asked Questions (FAQs)

We have added some of the frequently asked questions so that you guys can get a thorough idea about the subject.

Conclusion

Issues with the carburetor can destroy the equipment in different ways. Many of the equipment issues start with the carburetor. This is why it is vital to ensure regular maintenance of the equipment.

What happens if you put grass in your carburetor?

Deposits inside the carburetor can clog fuel and air passages and reduce performance or stop the engine altogether .

Why do carburetors stick to the throttle?

The connections attached to the carburetors' throttle and choke plates can bind or stick when dirty. Constant vibration and wear can affect the setting of the carburetor's mixture screws.

Why is my carburetor black?

Make sure that the air coming into the carburetor is clean and free of debris by inspecting the air filter. A clogged air filter is a common cause for black smoke emitting from the exhaust.

Can you clean a carburetor without removing it?

Luckily, you can take care of many of these problems quickly and easily; often without even removing the carburetor from the engine. Commercially available carburetor cleaner comes in convenient spray cans for periodic cleaning of both inside and outside the carburetor.

Why won't my small engine start?

Determine why your small engine won't start by checking your fuel levels, spark plug, carburetor, valve & compression levels and more. Follow along to troubleshoot and learn when it's best to service your engine.

Why is my outdoor generator not starting?

Stale fuel, dirt, and debris are the most common cause of outdoor power equipment not starting or running properly. If you store equipment with untreated gas in the tank, it can lead to engine damage.

Is your Spark Plug faulty?

Disconnected, dirty or fouled spark plugs are common causes for engines that won’t start. For small engines, spark plugs typically need to be replaced every season or after 25 hours of use.

Are you having Ignition problems?

If your spark plugs look good, problems with your ignition system can also be preventing a spark.

Is your Carburetor clean?

The carburetor regulates how air and fuel move through the engine. A dirty carburetor can cause poor engine performance or starting problems.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9