- Remove the recoil housing cap Unscrew the cap that holds the pulley to the recoil starter housing. ...
- Untie the rope Untie the knot in the rope and slide it out of the housing.
- Replace parts (if needed) Swap out the pulley, housing or spring if the parts need replacing.
- Re-tension the spring Now it's time to re-tension the spring. ...
What causes a recoil starter to fail?
Your recoil starter may also fail because the pulley or recoil housing has worn and the spring no longer sits in the housing correctly. We used a Briggs and Stratton starter for this repair, but most starters will require the same steps. Visit our Briggs and Stratton parts page to find the right parts for your Briggs and Stratton starter.
How do you fix a broken recoil starter?
In many cases you can remedy a broken recoil starter with a screwdriver, the stock parts and about 20 minutes of time. Since eReplacementParts.com stocks a wide assortment of small engine parts. You can find the recoil housing, spring or pulley you need for those times when the repair requires more than just re-tensioning the spring.
Where can I buy recoil housing parts?
Since eReplacementParts.com stocks a wide assortment of small engine parts. You can find the recoil housing, spring or pulley you need for those times when the repair requires more than just re-tensioning the spring.
How to keep the pulley from spinning on a recoil spring?
Once you have tensioned the spring, use a small screwdriver to keep the pulley from spinning. 5. Attach the cap Reattach the cap that holds the pulley to the recoil housing. While the cap will secure the assembly, it will not prevent the pulley from spinning, so keep a good grip on the pulley.
See more
How do you fix and rewind Briggs and Stratton pull starters?
2:119:44Briggs & Stratton Recoil Starter Service - YouTubeYouTubeStart of suggested clipEnd of suggested clipThen remove the Paul's. And Paul Springs if your starter uses them lift out the pulley assembly.MoreThen remove the Paul's. And Paul Springs if your starter uses them lift out the pulley assembly.
How do you fix a pull start that won't retract?
0:412:58HOW-TO Tighten A Limp Starter Rope That Won't Retract On A Small EngineYouTubeStart of suggested clipEnd of suggested clipI'm just going to turn counterclockwise. One turn on this one if the rope was out further I would goMoreI'm just going to turn counterclockwise. One turn on this one if the rope was out further I would go two turns counterclockwise. And with this recoil here one turn counterclockwise fix.
How do you fix a small engine recoil starter?
1:334:37How to Fix the Start Recoil on a Lawnmower - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd simply cut the knotted end off. Then pull the rest of the rope away from the pulley. Now I wantMoreAnd simply cut the knotted end off. Then pull the rest of the rope away from the pulley. Now I want to remove the screwdriver again being careful to not allow this to recoil back.
How do you fix a recoil starter on a lawn mower?
0:171:19Replacing the Recoil Starter on a Lawn Mower - YouTubeYouTubeStart of suggested clipEnd of suggested clipPosition the new recoil starter in the blower housing and snap it into the retainer clips snap theMorePosition the new recoil starter in the blower housing and snap it into the retainer clips snap the recoil starter guard into place position the blower housing on top of the engine.
How do you rewind a recoil starter spring?
0:050:56How to Rewind a Recoil Starter Spring--A Quick Fix - YouTubeYouTubeStart of suggested clipEnd of suggested clipIn first I just align the tab on the spring with the notch and the housing. And then I just wind theMoreIn first I just align the tab on the spring with the notch and the housing. And then I just wind the spring back into the housing. And that's how simple it is to rewind a starter spring.
How do you fix a recoil spring on a starter?
2:0710:26Best 3 Ways To Install A Recoil Starter Spring On A Small Engine - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe first thing you want to do here is cut the zip tie. Again make sure you're wearing your safetyMoreThe first thing you want to do here is cut the zip tie. Again make sure you're wearing your safety glasses. So now I have to remove it from the casing grab a good pair of pliers.
How does a small engine pull start work?
The operator pulls the rope's handle or grip. This causes the rope to unwind around the crankshaft and spin it. The spinning motion of the crankshaft cranks the engine. The crankshaft's motion engages the flywheel, enabling the engine to start.
How do you fix a pull cord spring on a lawn mower?
How to Fix a Recoil Spring on a Lawnmower, step by step:Step 1: Remove the Recoil Housing Cap.Step 2: Untie the Rope.Step 3: Replace Parts (If Needed)Step 4: Re-tension the Spring.Step 5: Attach the Cap.Step 6: Reinstall the Rope.Step 7: Coil the Cord.Step 8: Reattach the Recoil Housing Cap.
How does a recoil spring work?
1:253:52Chainsaw Recoil Spring (How it Works) - Understanding for RepairYouTubeStart of suggested clipEnd of suggested clipIn this direction the more the pulley turns the more tensions being put on that spring you can seeMoreIn this direction the more the pulley turns the more tensions being put on that spring you can see that by the spring coils getting smaller and smaller as more tension is loaded onto them.
How do you replace a pull string?
2:033:54How to Replace the Pull Cord on a Small Engine by @Gettin' Junk DoneYouTubeStart of suggested clipEnd of suggested clipBut I've already replaced it you're gonna take this and spin it by hand against the spring. You keepMoreBut I've already replaced it you're gonna take this and spin it by hand against the spring. You keep spinning it over and over. Until you get to the point where you have a lot of tension.
How do you fix a pull string?
3:374:27DIY: Replacing a Broken or Worn Pull Cord - YouTubeYouTubeStart of suggested clipEnd of suggested clipBe sure the knot is tight cut off the excess working end and then use a lighter to fuse the fibers.MoreBe sure the knot is tight cut off the excess working end and then use a lighter to fuse the fibers. You should have something like this when done and you can see roughly the length of the pull cord.
How do you fix a pull cord on a generator?
0:100:54Champion Help Center: Starting a Generator with a Broken Recoil RopeYouTubeStart of suggested clipEnd of suggested clipHere's a simple trick to make sure you still have power when you need it remove. The three boltsMoreHere's a simple trick to make sure you still have power when you need it remove. The three bolts holding on the recoil housing to remove the recoil. And take out the broken Rico rope.
How do you fix the pull cord on a trimmer?
4:3110:06Fix a broken pull rope on a Ryobi trimmer - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce the rope is through the hole all we need to do is make a very tight knot so the rope won't goMoreOnce the rope is through the hole all we need to do is make a very tight knot so the rope won't go back through the hole. Again. Pull the knot against the pulley. And then replace the pulley.
Why is the pull cord stuck on the pressure washer?
If the starter rope won't budge when you try to pull it, the engine may be locked up or the recoil starter may have failed. If you tipped the pressure washer on its side recently, oil may have filled the cylinder, preventing the engine from spinning.
How to replace a spring on a recoil starter?
1. Remove the recoil housing cap. Unscrew the cap that holds the pulley to the recoil starter housing. If your spring has slid out of the slots in the housing, then you can continue with the repair. If the housing, pulley or spring have failed, then you will need the proper replacement parts before continuing. 2.
How long does it take to fix a recoil starter?
Luckily, when this happens, you can fix your recoil starter in about 20 minutes. Your recoil starter may also fail because the pulley or recoil housing has worn and the spring no longer sits in the housing correctly. We used a Briggs and Stratton starter for this repair, but most starters will require the same steps.
How to keep a pulley from spinning?
With the pulley in the recoil housing, turn it about six times. Once you have tensioned the spring, use a small screwdriver to keep the pulley from spinning. 5. Attach the cap. Reattach the cap that holds the pulley to the recoil housing.
How to fix a broken starter?
Coil the cord. Hold the recoil starter firmly--it is still under tension--and remove the screwdriver. Pull the starter cord tight and then let go of the pulley. Control the rope speed as the pulley winds the rope back into the starter. Conclusion You can easily repair a broken small engine recoil starter yourself.
Why does my lawn mower's recoil starter fail?
In most cases, the recoil starter fails because the spring slides out of place, causing it to lose tension. Luckily, when this happens, you can fix your recoil starter in about 20 minutes. Your recoil starter may also fail ...
Can a small gas engine recoil starter be repaired?
As anyone who works with lawn equipment knows, small engine recoil starters eventually fail.
