Method 1 Fixing a Two-Handle Delta Faucet
- Confirm that the leak is at either the handle or spout. If your two-handled cartridge-style faucet is dripping from the spout, it’s likely due to faulty rubber O-rings.
- Close one supply line to see if it’s a hot or cold water leak. ...
- Shut off both supply lines and open both taps to drain them. ...
Full Answer
How to fix a leaky delta style bathroom faucet?
Repairing your old Delta faucet
- Turn off the water supply to your shower. ...
- Go outside and turn on any of your home’s wall hydrants or faucets. ...
- After you have removed this screw, the bonnet nut will also have to be removed. ...
- Equip yourself with a pair of fine tweezers. ...
- Once you have removed both the springs and the seats, inspect the inside of the housing. ...
How do you repair a Delta single handle faucet?
Things You'll Need
- Parts kit.
- Silicon Plumbing Grease
- Flat Screwdriver
- Needle Nose Pliers
- Channel Lock Pliers
How to fix Delta Faucet leaking from handle?
Things You Will Need
- Allen wrench, 18-inch
- Flat-head screwdriver
- Rubber gloves
- Adjustable pliers
- White vinegar
- Replacement springs and gaskets
How to repair Delta Faucet single handle?
- Look to see whether the spout is dripping—this is the most common cause of a leak. ...
- Shut off the hot and cold water supply valves, which are usually silver knobs under the sink. Turn on the faucet to drain any water in the lines. ...
- After removing the screw cover on the faucet handle, use a screwdriver to lift off the actual handle. ...
How do you fix a Delta 2 handle bathroom faucet?
1:323:15How To Fix A Leaky Delta Two Handle Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse a wrench or channel lock pliers to loosen the bonnet nut make sure to note where the quarterMoreUse a wrench or channel lock pliers to loosen the bonnet nut make sure to note where the quarter term stop is set on top of the cartridge. And use a pair of pliers to grab the top of the cartridge.
How do you fix a leaky Delta single handle bathroom faucet?
0:004:37Delta Peerless Bathroom Single Handle Faucet Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd just use a small slotted screwdriver and pry off the decorative cover to loosen that set screwMoreAnd just use a small slotted screwdriver and pry off the decorative cover to loosen that set screw you can use 1/8 inch allen wrench or you can get this combo tool and this has 1/8 inch allen wrench.
How do you fix a old delta bathroom faucet?
2:136:33HOW TO REPAIR LEAKY OLD 3 PCS DELTA FAUCET - YouTubeYouTubeStart of suggested clipEnd of suggested clipLet's go ahead and take our cartridge back. And slide that thing back into place kind of like that aMoreLet's go ahead and take our cartridge back. And slide that thing back into place kind of like that a little brass nut to hold it all into. Place. Take it easy don't force anything don't cross thread.
How do you fix a Delta single handle faucet?
0:344:06How To Rebuild A Delta Single Handle Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce we have the handle took off we're going to need to open our rebuild kit as it has the tool toMoreOnce we have the handle took off we're going to need to open our rebuild kit as it has the tool to loosen that nut on the top of the faucet. The part numbers gonna be at our b-36.
How do you take apart a Delta faucet?
1:018:56Delta Kitchen Faucet Leak Repair (Single Handle) - YouTubeYouTubeStart of suggested clipEnd of suggested clipWith the water off turn the faucet to the on. Position. This is a double check to make sure thatMoreWith the water off turn the faucet to the on. Position. This is a double check to make sure that your water is off use a 1 8 inch hex head wrench to remove the set screw in the handle.
How do you disassemble a Delta faucet?
2:4710:00Delta Faucet Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipNext step we're going to be removing the cap assembly. We'll do that by using our adjustable wrenchMoreNext step we're going to be removing the cap assembly. We'll do that by using our adjustable wrench again this is a smooth draw wrench as we're not we don't want to scar the finish of the product.
How do I know what model Delta faucet I have?
The model number is on all packaging, some faucets, and all installation instructions provided with your faucet. On the packaging, look near the UPC code or the top of the box. On the faucet, a model identification tag has been attached to most models manufactured since 2012.
How do you change a old Delta faucet cartridge?
2:576:30How to Replace a Delta Faucet Shower Cartridge - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse a strap wrench or a pair of channellock pliers to loosen the bonnet nut by turning itMoreUse a strap wrench or a pair of channellock pliers to loosen the bonnet nut by turning it counterclockwise then remove the bonnet nut by hand.
Are all Delta faucet cartridges the same?
The Delta 1300 and 1400 Series Trim Kits include the single function cartridge. The Delta 1700 Series Trim Kits include the Dual-Function Cartridge. The 17T Series Trim Kits all come with the Dual-Function Thermostatic Valve Cartridge. Remember from before, ALL TRIM KITS USE THE SAME VALVE.
How do you take apart a Delta faucet head?
0:462:21How To Clean a Delta® Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipLikely just that mineral build-up you'll need to remove your spray wand don't worry this is superMoreLikely just that mineral build-up you'll need to remove your spray wand don't worry this is super easy on some faucets you can just remove your spray wand by simply unscrewing it.How To Clean a Delta® Faucet - YouTubehttps://www.youtube.com › watchhttps://www.youtube.com › watchSearch for: How do you take apart a Delta faucet head?
How do you take apart a single handle bathroom faucet?
1:114:00How to Replace the Seats & Springs in a Single Handle Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse the needle nose pliers to unscrew the adjusting ring. Place a cloth over top and use the channelMoreUse the needle nose pliers to unscrew the adjusting ring. Place a cloth over top and use the channel lock pliers to unscrew the cap. Now pull out the ball the cam and packing.How to Replace the Seats & Springs in a Single Handle Faucet - YouTubehttps://www.youtube.com › watchhttps://www.youtube.com › watchSearch for: How do you take apart a single handle bathroom faucet?
How do you take apart a single handle faucet?
0:182:44Repairing a Leaky Single Handle Ball-Type Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis may require using an Allen wrench to loosen the handle. There may be a button that covers theMoreThis may require using an Allen wrench to loosen the handle. There may be a button that covers the screw that needs to be removed first and then you can loosen the screw and remove the lever handle.Repairing a Leaky Single Handle Ball-Type Faucet - YouTubehttps://www.youtube.com › watchhttps://www.youtube.com › watchSearch for: How do you take apart a single handle faucet?
What is a delta faucet?
Delta bathroom and kitchen faucets with two handles often are stem-style faucets that include a neoprene valve seat and spring that fits into the faucet below a cartridge-like insert stem. This is different from a true cartridge-style faucet, which closely resembles a stem faucet but does not have valve seats and springs.
How to tell if a faucet is leaking?
Determine Which Side Is Leaking. Place your hand under the drip from the faucet. If the water is warm, the leak is most likely on the hot side of the faucet. If the water is cold, the leak is most likely on the cold side. This tells you which is the better side to fix first, but it's possible that both sides are leaking in any case.
What is a stem style faucet?
With a stem-style faucet, a neoprone valve seat and spring fits into the water inlet port in valve body. Over the valve seat and spring, the stem is held into the body with a bonnet nut; the handle then fits onto the top of the stem. Leaks in this type of faucet usually can be fixed with a new neoprene valve seat and spring.
How to remove valve seat and spring?
Remove the seat and spring by inserting a small screwdriver or Allen wrench into the hole of the seat and pulling up both parts together. Note the spring's orientation inside the valve seat. The spring should be slightly larger in diameter at the bottom than at the top—where it fits into the seat.
How to replace a valve stem?
If desired, you can also replace the O-ring (which is sometimes included with stem-and-spring kits) or the entire stem. Fit the stem into its housing, aligning the tabs on the stem with the slots in the housing. Push the stem all the way down until it stops.
How do I shut off the water in my kitchen sink?
The valve may have a small football-shaped handle or a lever or knob. Turn the handle clockwise until it stops. Open the hot or cold faucet, as appropriate , to make sure the water is off.
Where is the valve seat on a faucet?
Look inside the stem housing and locate the neoprene valve seat sitting in a hole at the bottom of the faucet housing. The valve seat is a small, black, rubber cap with a hole in the top. Sitting inside and below the seat is a small metal spring.
