Take the broken part and a similar undamaged part to the millwork or woodworking shop for duplication. Carefully clean the old adhesive from the joints. Then reassemble the chair with the new part, gluing each joint. Clamp the chair with strap clamps until the adhesive dries, and then refinish the chair completely.
Full Answer
How to fix a broken office chair?
Take the broken part and a similar undamaged part to the millwork or woodworking shop for duplication. Carefully clean the old adhesive from the joints. Then reassemble the chair with the new part, gluing each joint. Clamp the chair with strap clamps until the adhesive dries, and then refinish the chair completely.
Can all wooden chairs be repaired?
With common sense and a few particulars, you can keep all your wooden chairs in good repair. Here's how to replace loose or broken chair parts:
How do you fix loose rungs on a rocking chair?
But those problems can often be repaired. Loose rungs or spindles -- and, where no bracing is used, loose legs -- can sometimes be mended by forcing glue into the joints. But a part mended this way may work loose again. For a more permanent repair, carefully separate the part from the frame.
How do you fix broken dowels on a chair?
Separate the joint carefully with an old screwdriver or a stiff-bladed putty knife, then replace the dowels. Make sure the joint is clean and dry before you reassemble it. Sometimes you can use a mechanical fastener -- an angle brace or a chair leg brace -- to mend the frame.
How do you replace a chair stretcher?
0:569:15How to Replace Broken Chair Parts - Chair Stretcher - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst thing I need to do is take that cushion off so I've got screws to undo. And then I can startMoreFirst thing I need to do is take that cushion off so I've got screws to undo. And then I can start taking it. Apart.
How do you fix a broken chair support?
6:509:16Tools and Tips to Fix Wooden Chairs - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow that is replacing a part sometimes you can glue something together where it just needs someMoreNow that is replacing a part sometimes you can glue something together where it just needs some reinforcement adding in a spline is an example of that a spline is a slot cut in the wood.
How do you fix a broken chair leg support?
0:233:49Fixing a broken chair leg - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd I put way too much glue in there just to be on the safe. Side. With the glue stronger than theMoreAnd I put way too much glue in there just to be on the safe. Side. With the glue stronger than the wood this is now good as new which unfortunately isn't good.
How do you fix a broken dowel on a chair?
0:361:49How to Replace a Chair's Broken Dowel Rods - YouTubeYouTubeStart of suggested clipEnd of suggested clipAround. It the secret to replacing an old dowel is plenty of glue. A lot of people put a little bitMoreAround. It the secret to replacing an old dowel is plenty of glue. A lot of people put a little bit of glue on the dowel and stick it in there some people put a drop in the hole and shove it in there.
How do you fix a broken chair spindle?
2:204:36Fixing a Broken Spindle in the back of a Chair (WnW #7) - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then I used a quarter inch bit to go a little bit deeper same thing with the end of the dowel.MoreAnd then I used a quarter inch bit to go a little bit deeper same thing with the end of the dowel. And then I fit a little quarter inch dowel in that to join the top dowel to the spindle.
How do you fix hydraulics on a chair?
0:414:41DIY: How to Fix Sinking Chair (In under 5 minutes!) - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce they bottom out against the top rank. Begin tightening them down about one turn per boltMoreOnce they bottom out against the top rank. Begin tightening them down about one turn per bolt alternating back and forth.
How do you reattach a chair leg?
3:3914:27How To Repair A Broken Chair Leg Or Table Leg - DIY Furniture Repair ...YouTubeStart of suggested clipEnd of suggested clipCut um you know using these saws. So i went ahead and i cut this off and this is a really importantMoreCut um you know using these saws. So i went ahead and i cut this off and this is a really important part. But yeah so we cut this uh so we cut this off flush using the japanese pull saw.
How do you glue chair joints?
18:1220:28How To Repair And Re-glue Loose Wooden Chairs Yourself - YouTubeYouTubeStart of suggested clipEnd of suggested clipHere and we'll squeeze. This together and tighten the clamps. Up. Okay so i went around and cleanedMoreHere and we'll squeeze. This together and tighten the clamps. Up. Okay so i went around and cleaned up all the glue all i did was use a you know water little spray bottle with water. And a dry rag.
How do you glue a broken chair leg?
0:385:47Quick broken chair leg repair and fix with dowels - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou bought these chairs our resale store and it looks like somebody had fixed this broken leg beforeMoreYou bought these chairs our resale store and it looks like somebody had fixed this broken leg before didn't do a good job. So we're gonna clean all that out and do it properly first thing I will take
What can I use instead of wooden dowels?
For a super-strong joint that doesn't require a lot of precise fitting, try using epoxy and all-thread rod as a substitute for dowels and woodworker's glue. For a super-strong joint that doesn't require a lot of precise fitting, try using epoxy and all-thread rod as a substitute for dowels and woodworker's glue.
How do you fix a broken tenon?
2:107:26Fix Broken Chair Joints (Mortise and Tenon) - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow I'm going to do is cut this off glue this and let it sit overnight and it'll show you how IMoreNow I'm going to do is cut this off glue this and let it sit overnight and it'll show you how I reinforce all this. So this is going on here. So I need a bit of glue.
What is a dowel plate?
Dowel Plates Use a Dowel Plate to easily make exact-sized dowels from any wood you choose. Also useful for making precise tenons on chair spindles. 5-1/8" long x 1½" wide x ¼" thick, made from surface ground A2 Tool Steel, hardened to 60 RC. Holes are machined with a 6° clearance taper on the underside.
How to fix a broken chair?
Take the broken part and a similar undamaged part to the millwork or woodworking shop for duplication. Carefully clean the old adhesive from the joints. Then reassemble the chair with the new part, gluing each joint. Clamp the chair with strap clamps until the adhesive dries, and then refinish the chair completely.
Which part of a chair suffers the most wear and tear?
The seat is the part of a chair that suffers the most wear and tear, which means it also is the most likely candidate for repairs. We'll cover various seat repairs in the next section.
How to cut a tenon rung?
Very loose legs or rungs can be wedged to fit if the tenon is sound. Clamp the part in a vise or have a helper hold it, then saw very carefully into the center of the tenon end. The cut must be square and centered, roughly the depth of the part that fits into the socket -- about 3/4 inch. For small parts, use a hacksaw or a coping saw to make the cut; for thicker parts, use a backsaw or combination saw.
How to fix loose rungs?
Loose rungs or spindles -- and, where no bracing is used, loose legs -- can sometimes be mended by forcing glue into the joints. But a part mended this way may work loose again. For a more permanent repair, carefully separate the part from the frame. If both ends are loose, remove the entire piece. For very stubborn joints, twist the part slightly to break the glue bond; if necessary, use self-locking pliers. Pad the part to prevent damage to the wood from the pliers.
How to fix a cracked tenon?
If the tenon end is cracked, you'll have to reinforce it. Apply a thin coat of glue to the tenon, and wrap it tightly with silk thread. If necessary, apply more glue and cover the tenon with another layer of thread. Let the threaded tenon dry for a day, and then glue the reinforced end firmly into the socket.
What to do if you catch a loose joint?
If you catch a loose joint in time, repair it with glue. If the joint is broken, you'll have to disassemble it and replace the dowels. The triangular glue blocks will probably be glued and screwed to the frame, and the dowel joint might even be supported with hidden nail or screw fasteners.
How to reinforce a broken piece of wood?
The best reinforcement is a dowel (wooden peg) pinning the broken pieces together. Use 1/8-inch to 3/8-inch dowel, depending on how thick the broken part is; drill the dowel holes with a bit the same size.
How to get rid of old glue on a stretcher?
New glue will resist sticking to old glue. If you can, get into the space with a piece of sandpaper to remove any remaining glue. Now use a C-clamp to help position the stretcher against the leg.
How to protect a chair from a pipe clamp?
Use two blocks of wood at either end to protect the chair from the pipe clamp. Tighten the pipe clamp against the blocks.
How to get glue out of a drywall wall?
If you do choose to glue, carefully use a utility knife to scrape away any old glue you can see. New glue will resist sticking to old glue. If you can, get into the space with a piece of sandpaper to remove any remaining glue.
Can you take apart a dowel?
You could take every piece apart just to replace the dowel, but why do that when there’s an easier and faster way!
How to remove a broken tenon from a mortise?
Start by removing the broken tenon from the front leg mortise by drilling out the waste with an undersize drill bit. If the break is jagged, roughly create a flat area so the bit won’t wander. Be careful how deep you drill; usually you’ll feel the drill bit finding the bottom of the mortise.
How to mark mortise on a rail?
As a rule, I usually reference off the insides. Set the depth of the mortise and the width to around 1/4 in. from the edges of the rail. Cut the mortise square to the shoulder.
How thick is a mortise in a leg?
Test the fit with thickness spacers. After being pared clean, this mortise in the leg was exactly 3/8 in. I stacked a 1/4-in. and a 1/8-in. spacer to test the mortise thickness.
