- Turn the fountain water pump off. Dip out any standing water in the fountain bowl with a cup.
- Dry the fountain with a towel. Allow at least 24 hours for the water to dissipate from the concrete.
- Clean the repair areas with a wire brush to remove any small particles of concrete that have broken.
- Brush the areas you cleaned with a wire brush with a stiff-bristle paintbrush to remove concrete dust from the areas for good adherence.
- Squirt both tubes of concrete epoxy onto a paper plate. One of the tubes contains a bonding agent and the other is a hardener.
- Mix the two products together thoroughly with a plastic spoon until the patching agent is a consistent color.
- Fill cracks in a cement fountain by forcing the epoxy into the cracks to fill them to the surface level, advises Concrete Network.
- Apply a generous amount of epoxy on the attachment areas of a figurine and the area that it fits on the fountain.
- Allow the epoxy to dry completely for 24 hours. Remove the duct tape if you repaired a figurine.
- Apply a coating of concrete sealer onto the entire cement fountain on the outside and inside, using a paintbrush.
- Allow the sealant to dry for 24 hours before turning on the fountain water pump. ...
How do you fix a broken cement fountain?
Remove the duct tape if you repaired a figurine. Apply a coating of concrete sealer onto the entire cement fountain on the outside and inside, using a paintbrush. The sealer repels ultraviolet rays from the sun and seals the surfaces so it does not absorb water and results in cracks or breaks.
Can I use Sani-tred® to repair and waterproof my concrete fountain?
If you have a concrete fountain that has cracks, leaks, or other imperfections that affect its ability to function, you can use SANI-TRED® to repair and waterproof it.
Do concrete fountains have cracks?
A concrete fountain is a water feature that can do a lot for the look and atmosphere of your backyard, but that doesn’t mean they’re always perfect. Sometimes, even the best looking fountains can have cracks that affect water flow.
Can a fountain be repaired?
You can also repair resin, fiberglass or plastic-type fountains with the correct sealers. Examine the fountain carefully to determine if it is a fiberglass, resin-cast fountain, plastic or concrete.
How do you fix a crack in a cement fountain?
Step 1: Clean the Fountain. Turn off the fountain and drain the water basin completely. ... Step 2: Determine the Extent of the Damage. ... Step 3: Use Epoxy for Broken Stone. ... Step 4: Fill Small Cracks With Cement. ... Step 5: Use Cement for Larger Holes. ... Step 6: Seal the Fountain. ... Step 7: Restart the Fountain.
How do you seal a leaking concrete fountain?
Concrete must be clean and free of previous sealers and paints. The birdbath and fountain must be completely dry before sealing. Fill in any cracks with a concrete crack filler where water may be leaking through. Use a penetrating concrete sealer or durable concrete coating to seal the birdbath and fountain.
What do you use to seal a concrete fountain?
SANI-TRED® is a liquid rubber waterproof coating that will seal your concrete fountain with superior protection. SANI-TRED® adheres to concrete, getting into the pores and bonding on a molecular level, leaving you with a concrete fountain that is completely and permanently waterproof.
How do you restore an old water fountain?
0:369:42Fountain Repair: How to paint your fountain! PART 1 - YouTubeYouTubeStart of suggested clipEnd of suggested clipWith some these foam brushes excuse the foam brush to just go over the fountain to add the concreteMoreWith some these foam brushes excuse the foam brush to just go over the fountain to add the concrete die. If you have any pumps or lights or whatever I'd recommend bag them up in a plastic bag.
Can You Use Flex Seal on a fountain?
Since Flex Seal is waterproof, protects surfaces from corrosion and comes in a variety of vibrant colors we knew it would be the perfect match for our tabletop fountain!
How long do concrete fountains last?
And even if it is covered, they aren't likely to last more than probably 5-8 years, as over time tarps or covers tend to get holes or sweat on the underside – and those droplets of moisture start the damage process as it infiltrates the stone and freezes over winter.)
Can you seal concrete with epoxy?
Epoxy Sealer Application Epoxy sealers form a high-build protective film on the concrete surface, producing a hard, long-wearing, abrasion-resistant finish. They also offer excellent water repellence. They are available clear or pigmented, if you wish to add color. Most products impart a glossy finish.
What paint to use for a concrete fountain?
Concrete water fountains can be painted with an exterior latex or oil-based paint. You can also use a concrete stain. If you go with a stain, you need to remove the old paint and sealer with a concrete and masonry paint stripper.
How do you fix a broken concrete birdbath?
1:373:00How to Repair a Concrete Birdbath - YouTubeYouTubeStart of suggested clipEnd of suggested clipSmear some of the epoxy on a putty knife then work the epoxy into the cracks in your birdbath. Fill.MoreSmear some of the epoxy on a putty knife then work the epoxy into the cracks in your birdbath. Fill. All cracks evenly. Making sure no cracks show when finished.
Can you repair a cracked fountain?
The exact material used to repair a cracked fountain depends on what it is made of -- epoxy-based patching materials usually work best for concrete fountains, while metal or fiberglass fountains can be repaired with waterproof silicone or similar fillers.
What do you do with a broken water fountain?
How to Repurpose Your Fountain and Save WaterRepurpose your fountain as a flowerbed. ... Reuse a patio fountain as an herb garden. ... Transform your fountain into a centerpiece. ... Turn your fountain into garden art. ... Repurpose your fountain into a cold beverage bin for parties.More items...•
How do you paint a concrete outdoor fountain?
Coat the fountain with concrete sealer. Apply it with a paintbrush to get into all the small decorative areas. ... Apply a primer. Use a new paintbrush to apply a paint primer. ... Paint the fountain using an oil-based paint. The oil-based paint will help protect the fountain from water damage.
How do you seal a leaking concrete pond?
2:446:31Burke's Backyard, Fixing a Leaking Pond - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere's a number of quite big holes and to plug them we're going to use a thing called max plug.MoreThere's a number of quite big holes and to plug them we're going to use a thing called max plug. This is what's known as a hydraulic cement. So you make it up sort of like putty.
How do you seal a rock fountain?
Step 1: Clean and Rinse the Fountain. ... Step 2: Prepare the Sealer. ... Step 3: Spray or Paint the Sealer onto the Fountain. ... Step 4: Wipe off Excess Sealer. ... Step 5: Allow the Sealer to Dry. ... Step 6: Apply a Second Coat.
Why is my water fountain leaking?
Q: Why is my fountain leaking? A: This is typically caused by over-filling the wall fountain. Most wall fountains have a tray inside the water basin that holds water. If water gets outside this tray or if the tray is overfilled it may leak out the bottom making it appear that the fountain is leaking.
What is the best paint for a concrete fountain?
Concrete water fountains can be painted with an exterior latex or oil-based paint. You can also use a concrete stain. If you go with a stain, you need to remove the old paint and sealer with a concrete and masonry paint stripper.
How to make a resin repair?
1. Pour the resin or liquid plastic material into one cup, and pour the catalyst into another as the amounts needed for the repair job. Only create small batches at a time, as once you combine the resin or plastic with the catalyst, you must work quickly to avoid the material hardening in the cup.
What to wear to avoid concrete dust?
Wear goggles and a dust mask to avoid getting concrete dust in your eyes and lungs. Writer Bio. As a native Californian, artist, journalist and published author, Laurie Brenner began writing professionally in 1975. She has written for newspapers, magazines, online publications and sites.
Can you use epoxy to fill cracks in concrete?
If you are using an epoxy sealant, mix only the amount needed to completely fill the crack, otherwise it will harden and go to waste. For cracks that go all the way through concrete, use an two-part injection product that requires mixing as in Step 1 and 2 of the previous section.
Can you use caulk to fill cracks?
Verify the material fills up the crack fully. Some liquid crack fillers can be applied using a caulking gun, while others may be applied directly from the bottle.
Can you use epoxy to repair a concrete fountain?
For example, you can use a concrete patch or epoxy material to repair a concrete fountain, but for a resin, fiberglass or plastic fountain, you'll need a liquid plastic or resin-type sealant to make the repair.
Can you repair a broken concrete fountain?
Cement fountains generally last many years before developing small cracks, crumbles or figurines that release from the base. Cement repair is easily accomplished by the do -it-yourself homeowner in short time and with little expense.
Can you glue concrete back together?
Do not try to use concrete to glue the pieces back together – it won’t work, so don’t waste your time. Once you have the epoxy glue correctly mixed, simply apply it to the damaged areas, clamping them together until the glue is completely dry.
How do you seal a leaking fountain?
Apply a coating of concrete sealer onto the entire cement fountain on the outside and inside, using a paintbrush. The sealer repels ultraviolet rays from the sun and seals the surfaces so it does not absorb water and results in cracks or breaks.
Do I need to seal concrete fountain?
Birdbaths and fountains are frequently constructed out of concrete and should be treated with a concrete sealer in order to presevere their life, prevent cracking, water penetration and organic growth such as mold and mildew.
How do you waterproof a concrete fountain?
After you’ve painted the surface of the fountain, any clear waterproof coating will work to waterproof the fountain. If you have a concrete fountain, look for a sealant like a concrete and masonry sealer that will provide protection against harsh weather.
How do you reattach a broken concrete?
Spread a heavy layer of Loctite Metal And Concrete Epoxy on the surfaces to be joined and press the broken piece into position, leaning a heavy block against the repair until the epoxy sets. Leave undisturbed for 24 hours.
What glue will stick to concrete?
SAKRETE Concrete Glue is a liquid latex bonding adhesive for bonding new concrete, mortar or gypsum plaster to existing surfaces. Ready to use and easy to apply, it eliminates the need for roughing or scoring old surfaces.
How to keep algae out of cement fountain?
Add water clarifiers to keep algae from forming in your cement fountain. Seal pond and pool cement fountains in the same manner after draining water to a level of 6 inches or more below the areas of repair. Mary Lougee has been writing for over 10 years.
How long does a cement fountain last?
Cement fountains generally last many years before developing small cracks, crumbles or figurines that release from the base. Cement repair is easily accomplished by the do-it-yourself homeowner in short time and with little expense. After the repairs are made, you can re-seal your entire fountain with a clear sealant or paint it to create ...
How to hold a fountain in place?
Place the loose end of a roll of duct tape on the center of the figurine and wrap the tape tightly around the fountain to hold it in place . Make at least one revolution of duct tape around the entire fountain and figurine.
How to attach a figurine to a fountain?
Apply a generous amount of epoxy on the attachment areas of a figurine and the area that it fits on the fountain. Hold the figurine in place with one hand. Place the loose end of a roll of duct tape on the center of the figurine and wrap the tape tightly around the fountain to hold it in place. Make at least one revolution of duct tape around the entire fountain and figurine.
How to fill cracks in a fountain?
Force the epoxy to the cracks. This way, you will fill the cracks to the surface level. Then using a plastic trowel, level up the surface. Using enough quantity of epoxy, apply it on the figur ine and areas fitting on the fountain. Using one hand, hold the figurine in place.
How to make a fountain with epoxy?
Using one hand, hold the figurine in place. Then place one end, the loose one, on the center of the figurine and wrap it around the fountain. You should make at least one such revolution. Allow the epoxy to dry for a whole day. After drying, remove the tape.
How long should cement sealant dry before turning on water pump?
The sealant should be allowed to dry for a whole day before you decide to turn on the fountain water pump. With the above steps in mind, you are good to go in as far as repairing your broken cement fountain is concerned.
Can you fix a cement fountain in Orange County?
It is easy to do the cement repairs, but sometimes you need a professional to ensure that you completely fix the problem.
What is a concrete fountain?
A concrete fountain is a water feature that can do a lot for the look and atmosphere of your backyard, but that doesn’t mean they’re always perfect. Sometimes, even the best looking fountains can have cracks that affect water flow.
Can a broken fountain be repaired?
A cracked and broken fountain does no good for anyone, so it’s a good idea to repair, waterproof, and protect your fountain with a concrete leak sealer to keep it working its best.