How to Repair Craftsman Self Propelled Lawn Mowers
- Locate the self-propelled motor. If it's a front drive, the motor is between the front wheels on the deck.
- Spin each wheel. Look for any cracks. ...
- Inspect the spark plug located on the side of the motor. It is encased in a black hose. ...
- Turn the mower so that the handle is lying across the ground and the mower blades are visible. ...
Full Answer
How can I troubleshoot Craftsman lawn mower problems?
Troubleshooting a Sears Craftsman Riding Lawn Mower
- Does Not Start. Fill the fuel tank. ...
- Engine Does Not Turn Over. Press the clutch/brake pedal with your foot while starting the mower. ...
- Power Loss. Raise the cutting height or reduce your speed. ...
- Vibrations or Uneven Cutting. Turn the lawn mower on its side and clean the bottom of the deck to remove built-up leaves or grass.
- Grass Does Not Discharge Properly. ...
How to fix a lawn mower that won't start?
- Pull up the mower's hood to access the ignition switch.
- Remove its cable harness.
- Remove the tabs to pull the ignition switch out of its slot.
- Turn the key to the start position and set the multi-meter to measure resistance, not voltage.
- Connect the black multi-meter probe to the B prong and the other to the S prong. These terminals are along each other's diagonal at the bottom of the switch.
- Use the key to turn the ignition switch and start the engine. The resistance should display on the multi-meter when you do this.
How to repair Craftsman self propelled lawn mowers?
Some things that you have to check before working on your lanwmower:
- Safety gloves: Use safety gloves when you work with sharp or hot lawnmower parts. You also protect your hands from grease and oil spills.
- Use quality parts: Try to use quality parts. This can mean good OEM parts or genuine parts that the company recommends.
- Disconnect the battery: Disconnect the battery before working on your lawnmower. ...
How to fix a lawn mower with no compression?
- By reducing the cylinder diameter (to increase the compression ratio).
- By increasing the cylinder diameter (to decrease the compression ratio).
- By reducing the cylinder length/stroke length (to increase the compression ratio).
- By increasing the cylinder length/stroke length (to increase the compression ratio).
How do you disassemble a Craftsman lawn mower?
2:177:06Craftsman Lawn Mower Disassembly – Lawn Mower Repair HelpYouTubeStart of suggested clipEnd of suggested clipUse a flathead screwdriver to help pry off both wheel. Covers. Now use a 9/16 inch socket to helpMoreUse a flathead screwdriver to help pry off both wheel. Covers. Now use a 9/16 inch socket to help loosen the mounting nuts securing the wheels unthread the nuts and you can remove both wheels.
What would cause a Craftsman lawn mower not to start?
A Craftsman lawn mower won't start when the engine is not getting air, fuel or spark due to a plugged air filter, bad fuel, faulty switches, bad battery, bad spark plug, fuel blockages or dirty carburetor. Keep reading for my complete list of items that can prevent your Craftsman lawn mower from starting.
What causes a lawn mower not to start?
Your Mower Won't Start: If you have last season's gas in your mower, drain your fuel tank and fill with fresh gas. Other possible causes include: Loose, Dirty or Disconnected Spark Plug in Your Lawn Mower: Check it out, clean off debris, re-connect and tighten. Dirty Air Filter: Clean or replace.
How do you fix a Craftsman riding lawn mower that won't start?
1:145:56Lawn Tractor Won't Start? Try This Easy Free Fix! - YouTubeYouTubeStart of suggested clipEnd of suggested clipThen just tilt the hood forward a bit lift it up now. Here's where the problem lies. This is theMoreThen just tilt the hood forward a bit lift it up now. Here's where the problem lies. This is the choke lever over here you can see it's loose.
Why does my lawn mower only run for a few seconds then dies?
If your lawn mower starts, runs briefly, then dies these are the four most common reasons that's happening: Dirty carburetor / clogged carburetor bowl. Old gasoline that has gone bad. Dirty or defective spark plugs.
How do you clean a lawn mower carburetor without removing it?
Use Carburetor Cleaner Fortunately, you can generally do this without even taking the carburetor out of the engine. Start by purchasing some commercial lawnmower carburetor cleaner, which comes in a simple spray can and will make it easy to clean the inside and outside of the carb.
How do you fix a lawn mower that won't stay running?
0:166:26How To Fix Lawn Mower That Wont Stay Running! - YouTubeYouTubeStart of suggested clipEnd of suggested clipMy back or look for tools or anything like that. So the kit that I use to rebuild the carburetor.MoreMy back or look for tools or anything like that. So the kit that I use to rebuild the carburetor. And air filter and all cost less than ten dollars off of Amazon.
How do I know if my lawn mower spark plug is bad?
The more worn or dirty spark plugs are, the greater the tug on the rewind and more effort is required to produce an adequate spark. If you haven't turned on your engine recently, your mower won't start and/or you have to tug repeatedly on the rewind to start the engine, a damaged spark plug may be the culprit.
How do I clean the carburetor on my lawn mower?
2:095:13How to Clean the Carburetor on a Lawn Mower - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you want to make sure that's clean and the way you can do that is just simply get a piece ofMoreSo you want to make sure that's clean and the way you can do that is just simply get a piece of small wire. And see you and you poke it in and out of that hole make sure that it's clean.
Why does my riding lawn mower clicks but wont start?
If your riding lawn mower engine clicks when you turn the key but won't turn over, there's a pretty good chance your mower could have a bad starter solenoid. Other problems, though not as frequent, include a bad starter motor, a wiring failure, a weak battery or a locked-up engine.
Where do you spray starter fluid in a lawn mower?
Spray a light dose of starter fluid directly into the carburetor chamber of your mower. Set the engine speed to the midpoint, if the idle is adjustable, by hand. Set the engine choke to full choke, if equipped.
How do I clean the carburetor on my lawn mower?
2:215:13How to Clean the Carburetor on a Lawn Mower - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you want to make sure that's clean and the way you can do that is just simply get a piece ofMoreSo you want to make sure that's clean and the way you can do that is just simply get a piece of small wire. And see you and you poke it in and out of that hole make sure that it's clean.
Where is the fuel filter on a Craftsman lawn mower?
The fuel filter is usually along the front side or front of the engine. The fuel filter resembles a small rectangular piece and has a fuel line connecting to each end. Most Craftsman riding mowers and some push mowers have a fuel filter between the fuel tank and carburetor.
How do you get to the carburetor on a Craftsman lawn mower?
0:009:52Cleaning Carburetor on Craftsman Lawn Mower - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut this one actually if you lift it up right and you notice the plastic Clips it allows she liftsMoreBut this one actually if you lift it up right and you notice the plastic Clips it allows she lifts straight up and what we have here is we have a fuel hose. That. Actually has just a clip on it.
How do you start a self propelled Craftsman lawn mower?
8:3210:09CRAFTSMAN M230 163-cc 21-in Self-propelled Gas Lawn ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then you push it in the you turn your water on. And then you start your mower for like a. MinuteMoreAnd then you push it in the you turn your water on. And then you start your mower for like a. Minute.
Why is my Craftsman mower not working?
If your Craftsman self-propelled lawn mower suddenly stops working, it might be because the traction control cable is misadjusted or broken. Check if the traction control cable moves freely to see if it’s working properly. If it doesn’t, lubricate it by putting a small amount of oil into the end of the cable.
What is Craftsman lawn mower?
Craftsman, as hinted by its name, offers its products to people who are professional mechanics to those who have the tenacity to do things themselves. They also have a series of self-propelled, electric, push, and reel lawn mowers that you can avail of. Ultimately, Craftsman offers a wide array of products that range from clothing, replacement blades, flashlights, and other utilitarian tools.
How does a transmission work on a lawn mower?
When the transmission is powered by the drive belt, the lawn mower wheels will engage and turn. To ensure that your transmission is properly working, check and observe it while the lawn mower is up and running. The lawn mower wheels should be turning while the transmission pulley spins. If not, this means that your transmission is damaged or defective. Replace it completely as the transmission cannot be repaired.
What does a V belt do on a lawn mower?
The V-Belt is responsible for rotating the drive pulleys in order to drive the wheels of the lawn mower. if this part is broken or worn out, it means that your lawn mower wheels won’t be able to turn. To resolve this, check your V-belt first if there are damages. If there are, replace it completely.
What are the features of a self propelled lawn mower?
Some of which include grass-bagging, side-discharge, and safety features. There are also three-in-one models available that have mulching options as well.
What is hydro lock on a lawn mower?
Issue 2: Hydro-Lock. A hydro-lock can happen when the piston-cylinder is full of oil. This usually occurs when you tilt the lawn mower forward and hold it for a couple of minutes. In normal working conditions, the piston should move when you pull the starting rope.
How to remove a gear casing?
Using a flat screwdriver, you can put the casing off. Inside it, check first if there are any clogs in the gears. If there are, use a screwdriver to remove them. If the gears have any cracks, you will have to replace them. To do this, use a screwdriver again to remove the gears.
Why is my lawn mower carburetor clogged?
The carburetor might be clogged. A clogged carburetor is most commonly caused by leaving fuel in the lawn mower for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance.
Why does my lawn mower stall?
Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker , stickier substance. This sticky fuel can clog up the carburetor and cause the engine to stall.
What to do if cleaning carburetor isn't effective?
If cleaning the carburetor isn’t effective, rebuild or replace the entire carburetor. 05 - Spark Plug. Inspect the spark plug for signs of wear or damage. If the porcelain insulator is cracked, an electrode is burned away or damaged, or there is heavy carbon buildup at the electrode, replace the spark plug.
How to tell if spark plug is defective?
To determine if the spark plug is defective, use a spark plug tester. You should see a strong spark between the tester’s terminals when the engine is cranking. If there is no spark, this indicates that the spark plug is defective and should be replaced. Required Part.
