How to Troubleshoot a Hayward Pool Pump
- Check the Hoses. Tighten all hose connections on the pump and filter. ...
- Inspect the Pressure Gauge. Check the filter pressure gauge. ...
- Check the Skimmer Basket. Look into the skimmer basket for debris. ...
- Remove Debris. Remove debris from the pool pump basket. ...
- Inspect the Impeller. ...
- Backwash the Filter. ...
- Replace the Sand or DE. ...
How to replace a Hayward pool pump motor?
Remove the Motor Assembly - Slide the motor assembly back and away from the pump housing. Remove Diffuser and Impeller Wear Ring - Pull away the diffuser and impeller ring to reveal the impeller, then set these parts aside for reuse. Unscrew Impeller From Motor Shaft - Stabilize the back of the motor shaft with a 7/16th wrench so it cannot turn.
How do you drain a Hayward pool pump?
- Manually shut the pump off at the breaker box.
- Turn the multiport valve in a clockwise direction until you get to "Waste".
- Turn the pump back on.
- When you've taken enough water out of the swimming pool, turn the pump off.
- Rotate the handle on the multiport valve in a clockwise direction until you get back to "Filter."
- Turn the pump back on.
How to drain my pool with a Hayward pump?
- Turn the pump off.
- Roll backwash hose out into the yard or approved draining area.
- Rotate the multiport valve on the top or side in a clockwise direction to the “Waste” position.
- Turn the pump back on.
- After you get the correct amount of water out of your swimming pool, turn the pump back off.
How to unclog the Hayward Super pump impeller?
Insert a long screwdriver into the pump, as shown in the photo. Although you will not be able to see the impeller physically, you will be able to move it or turn it both clockwise and counterclockwise. If the impeller is clogged, it will be a bit difficult to move at first. Work the impeller both ways until it begins to move more freely.
How do you take apart a Hayward pool pump?
0:471:56Poolandspa.TV Swimming Pool And Spa Pump Repair Series - YouTubeYouTubeStart of suggested clipEnd of suggested clipOkay you're going to keep your wrench right there I'll brace against the side here you're going toMoreOkay you're going to keep your wrench right there I'll brace against the side here you're going to turn your pump to the side keeping your wrench there. And then you can grab the impeller.
Can a pool pump motor be repaired?
Most of the new generation of pumps are already equipped with automatic controls and safety features. In fact, if you take enough time to learn the manual, you might find yourself able to repair some of the problems on your own. Of course, there are repairs and replacements are best left in the hands of professionals.
What is the life expectancy of a Hayward pool pump?
On average, pool pumps last eight to 12 years before needing replacement. Over time, it's normal for pool parts to begin to wear down.
What would cause pool pump to stop working?
It could be something blocking it, a dirty pool filter, or too much air in the system. If there's something blocking your pump's suction, check your filter gauge. If it's 10psi above the normal reading, clean your filter. This will reduce pressure and reset your pump's flow.
Is it worth repairing a pool pump?
So generally, if you run across problems with your pool pump before the five or six year mark or if it's still covered by warranty, then repairing it is the way to go, after that mark, you may have to think about getting a new pool pump altogether as the other components of the pump may start to fail anytime as well.
Should I replace my pool pump or just the motor?
Replacing the entire pump can cost twice or even four times as much as replacing the motor. Some pool repairmen might try to talk you into replacing the entire pump, but you'll actually be better off with a simple pool pump motor replacement.
How do you know if pool pump is bad?
Don't Wait to Call for Swimming Pool Pump ReplacementAge. Yes, the age of your pump is an early trouble sign. ... Noise. Your pool pump should run quietly. ... Power Trip. Has your pool pump motor started to trip your electric breaker box more and more frequently? ... Swimming Pool Pump Motor Keeps Shutting Off. ... Loss of Suction.
Can I replace my pool pump myself?
A professional electrician will be needed to disconnect the wiring before a pump can be removed. Once a new pump is installed, an electrician will again be necessary to reconnect the wires to the new pump. A do-it-yourself homeowner with basic mechanical aptitude can replace the pool pump in a relatively short time.
How much does a new pool pump cost?
Pool pump installation costs between $700 and $1,500, or $1,100 on average. A single-speed pump can cost as low as $500 to replace, whereas a high-end pump or a project that requires new plumbing can run upwards of $5,450.
Why is my Hayward pool pump not turning on?
Check all connections, circuit breakers, and fuses. Repair or replace any tripped breakers or blown fuses. Inspect the motor shaft for any obstructions. Remove the pump and basket, then look for and remove any debris in the shaft.
What causes a pool pump to burn out?
A pool pump can overheat in two ways: because of an electrical problem or friction. While electrically related failures are by far the most common cause for pump overheating, as we will discuss at length, there is also the potential for a friction fire to develop if a pump is starved for water.
How much does it cost to repair a pool motor?
Pool repair costs:National average cost$100Average cost range$90-$130Low-end cost$30-$49High-end cost$1,515-$3,100Apr 26, 2021
How much does it cost to replace a pool pump motor?
between $250 and $650Pool Pump Motor Replacement Cost Including labor and materials, replacing the pool pump motor costs between $250 and $650. This can be a much more affordable option compared to replacing the entire pump, as long as your pump is expected to last for at least a few more years.
How do you rebuild a pool pump motor?
2:5111:43How To Rebuild And Install A Pool Pump Motor - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo just loosen it up and hold the wrench on the back and it'll come right off. You need to removeMoreSo just loosen it up and hold the wrench on the back and it'll come right off. You need to remove the seal. That's on the front of the pump here to split the pump apart.
How much does a pool pump motor cost?
Pool Pump or Motor Replacement Merely replacing the motor is less costly than replacing the whole pool pump. A DIY motor replacement costs around $25 to $200, while hiring a professional can cost an additional $40 to $100.
How to contact Hayward pool tech?
That’s all Folks! If these quick tips didn’t solve your problem, feel free to call our pool tech supporters at 1-800-288-7946 for more Hayward pool pump troubleshooting.
What causes a pool pump to leak?
On the plumbing side, you can have problems with air leaks, water leaks or just getting the water to flow properly.
How to spin a capacitor shaft?
To spin the shaft, disconnect power at the breaker and remove the capacitor (at 9 o’clock) and the thermal overload (at 12 o’clock) so that you can slip a 7/16” wrench onto the slotted shaft.
What to do if pump won't start?
If the pump won’t start or run, check these things. If the motor does not turn on, check the breaker and timeclock switches. If the motor hums but does not start, check that the shaft is free-spinning, then check the capacitor. If the motor makes no noise at all, check the wiring and terminal connections.
Why does my pump motor make a humming noise?
Makes Noise: If the pump motor makes a humming sound when trying to start, you likely have a bad start capacitor.
What to do if power is reaching the time clock?
If power is reaching the time clock or switch, check the wires running from the switch to the pump for any signs of damage, and inspect the connections on each end, for loose wires or insect infestation.
Why does my pump shut off?
Other causes of a pump shutting itself off include loose or broken wires or incorrect voltage, more than 10% more or less of the rated input voltage. In most cases however, a motor that is over-heating tends to be defective beyond repair, when caused by an internal short across the motor windings.
How to tell if pool pump is bad?
Check the filter pressure gauge. When troubleshooting a pool pump, the pressure gauge indicator gives you a good idea of problems. If the pressure gauge is running high and the return flow of water to the pool is low, then you know that the problem is probably either in the water entering the pool filter or in the pool filter itself.
How to fix a water pump that is dripping?
Step 1: Check the Hoses. Tighten all hose connections on the pump and filter. Before troubleshooting the filter or pump, make sure it is properly connected. Dripping hoses can cause air to get into the system, which prevents water from flowing. Filters require a vacuum environment, and air in the system will cause it to malfunction.
How to backwash a sand filter?
If you have a sand filter, perform a backwash by following the manufacturer' s instructions. Once you're done, turn on the filter to see if the problem is resolved. After backwashing, regenerating or cleaning your filter, make a mental note of the pressure gauge reading.
How to stop water from flowing in a water pump?
Tighten all hose connections on the pump and filter. Before troubleshooting the filter or pump, make sure it is properly connected. Dripping hoses can cause air to get into the system, which prevents water from flowing. Filters require a vacuum environment, and air in the system will cause it to malfunction.
What is Hayward filter?
Hayward makes a well-respected series of sand and diotomaceous filters for swimming pools . Hayward is a manufacturer that makes a well-respected series of swimming pool filter/pump units that use sand or diatomaceous earth (DE) for water filtration. They are remarkably trouble-free if used correctly and maintained as directed.
How to check if a skimmer is working?
Look into the skimmer basket for debris. If the problem is the water entering the pump, then open the skimmer lid, pull out the basket, and dump any debris sitting in the basket.
How to repair a pump that has a crack?
If the pump housing has cracked due to frozen water, it can be repaired using a plastic epoxy compound. The epoxy is mixed and then liberally applied over the crack. This forms a positive and watertight seal. If the crack is severe enough and the housing has broken apart, the housing and/or the motor must be replaced.
Why is my pool pump freezing?
The first, and most common, is that the pump has not been winterized -- totally drained of water -- and has literally frozen because of low temperatures. This situation can be completely rectified and the pump will run again. The second cause is that the motor bearings have seized up ...
How to check if water in a water pump is frozen?
1. Remove the filtration cover and the filter basket and check inside the filter housing for frozen water. If the pump has not been drained for winter and the temperature has dropped below freezing, the chances are that water in the pump has frozen.
How to get dirt out of motor housing?
Tap the side of the motor housing with a small hammer. Do not use much force and literally do a "tap-tap-tap" along the side of the motor housing to loosen up any dirt or rust that may have jammed the motor bearings.
How many unions can you add to a pump?
By allowing 4 inches of excess on either side, you can add in two unions when you reconnect the pump to the filtration system.