
Things You Should Know
- Turn on the sprinkler to locate the leak. Once you find it, turn the water off.
- Dig up the area above the leak to expose the damaged sprinkler line. Clean off the exposed section with a wet cloth.
- Saw off a 4 in (10 cm) section of pipe to remove the leak. Clamp the pipe ends and insert a slip coupling between them to repair the line.
How to tell if your sprinkler system needs repair?
To Winterize:
- See if your system has auto-drain valves. ...
- If you have manual drains, you'll need to use an air compressor with pressure between 50 and 100 PSI. ...
- Open the valve manifolds to allow any remaining water to drain.
- Hook up the air compressor and run air through each zone in your system until you've cleared all zones of water.
How to get air out of a sprinkler system line?
Steps How To Drain Your Sprinkler / Irrigation System:
- Turn off your water at the dedicated Sprinkler Line Shutoff (A) in your basement / crawlspace.
- Open the 2 Petcock’s (F) with a flat head screwdriver so that the screw head runs a 45 degree angle
- Open the Inside Drain (B) to drain your system. ...
- Open 2 Ball Valves (C & D) on backflow preventer (outside) to a 45 degree angle. ...
How do I repair a clogged irrigation line?
Repair Drip Irrigation Guide: How To Fix It Yourself Without Your Gardener
- Drip Irrigation Parts to Keep on Hand. In case of emergency, it’s always best to keep a stash of these inexpensive parts in the garage. ...
- Things to Know About Drip Tubing. ...
- Fixing Drip Irrigation. ...
- Installing Microspray Drip Irrigation. ...
- The Importance of a Pressure Regulator and Filter. ...
- Your Turn…. ...
How to cap off a sprinkler line?
Use these instructions if you live in an area that does not require winterization.
- To cap off a sprinkler, dig up the dirt around the head you want to remove exposing the pipe and fittings below.
- Unscrew the sprinkler and any piping connecting the sprinkler to the fitting below.
- Install a cap or plug of the appropriate size/thread to stop water from flowing out of the fitting after the sprinkler is removed.

How do you repair a punctured sprinkler hose?
0:323:01DIY - How to repair a cut sprinkler hose - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you cannot do this job if you once or twice. And that's it cut it right there insert that couplerMoreIf you cannot do this job if you once or twice. And that's it cut it right there insert that coupler in there you just push it in. And when you sure you wanna do here.
How do you fix a broken sprinkler wire?
0:344:26Easy way to fix or add a wire for irrigation zone - YouTubeYouTubeStart of suggested clipEnd of suggested clipUp it's going to decode it so that these two zones will run separately but we'll use the one goodMoreUp it's going to decode it so that these two zones will run separately but we'll use the one good wire coming off that valve that works and we'll be able to bypass the bad wire alrighty so here we go.
How do you splice a sprinkler line?
2:133:31How to "Tee In" to a PVC sprinkler line with a Quick Fix coupling - YouTubeYouTubeStart of suggested clipEnd of suggested clipPipe. The next step is to primer and glue the quickfix coupling on to the other end of the cup. PipeMorePipe. The next step is to primer and glue the quickfix coupling on to the other end of the cup. Pipe. The last step is to glue in the new pipe that will feed the other side of this sprinkler zone.
Can sprinkler system electrocute you?
If you put a quarter mile of pipe on wheels, connect some electric motors, pump water through this system and continuously move it around a 130-acre field soaking everything in site, you've just created a potential for someone to get electrocuted.
How do you find a cut sprinkler wire?
0:282:43Using a Pulser to Troubleshoot a Sprinkler System Wire BreakYouTubeStart of suggested clipEnd of suggested clipThe receiver goes parallel with the wire path. And when you turn it on there's an analog meter thatMoreThe receiver goes parallel with the wire path. And when you turn it on there's an analog meter that you'll watch when the needle bounces to the right that's the direction of the fault.
How do you repair a PVC T joint?
1:213:32Pipe Dream Slip Tee Repair Fitting - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd the nipple riser apply primer and cement to the outside of the pipe you're repairing on bothMoreAnd the nipple riser apply primer and cement to the outside of the pipe you're repairing on both sides of your cut and on the inside of both ends of the pipe dream slip teeth.
How to stop water from pouring out of pipe?
Clean the pipe. Some water will come pouring out at first, you could try to catch it, but it is easier to bail it out. Once the water stops coming out, clean both ends with a rag. ...
How long should a PVC pipe be?
Or you can buy a PVC fitting from most home improvement stores that has one pipe sliding inside an outer barrel with an O-ring inside. It will extend almost 3" in length. You may see in stores 1/2" to 2 1/2" in diameter sizes.
How to repair a split pipe?
Step 1: Cut Out the Bad PVC and Dry Fit Your Solution. Cut out the section of PVC that you wish to replace. If you're repairing a split pipe, ensure you remove enough pipe to include the entire split. In this instance, I only wanted to remove a small bit of pipe, but ended up removing about 4-5" in order to accommodate the elbows.
How long does it take for PVC pipe to drain?
Once you've cut into the PVC for the first time, allow some time for the line to drain. Depending on weather, this could take a few minutes, or even overnight. Cut short straight PVC sections that will fit into the elbows with almost no pipe showing.
What size elbows to use for PVC pipe?
PVC pipe at the diameter of your main line#N#4 x 90 degree elbows#N#PVC cutter [you can use other tools, but once you use a new pair of PVC cutters, you'll never go back]#N#PVC glue#N#Optional items:#N#Nylon thread tape#N#Sprinkler head#N#Other various PVC shapes
Can you glue elbows into existing pipe?
Once you're happy with the dry fit, you can glue the first 2 elbows into the existing line. In the picture, you can see that I've glued an elbow on each of the exposed underground pipe parallel to the existing line. You can do it this way or angle the elbows up or down, as long as they are parallel to each other.
