Begin with an electric drill equipped with a masonry bit and drill out the mortar around one brick. Once you remove this first brick, the rest should come out easily. When you reach the fireplace valve, you can repair or replace it.
How do you replace gas fireplace switch?
How to Install a Wall Switch to Gas Logs
- Turn the control switch on the gas fireplace to the "Off" position.
- Choose a convenient mounting location for the wall switch in accordance with the fireplace manufacturer's instructions.
- Run a section of two-conductor, low-voltage wire from the single-gang box to the control panel of the gas fireplace.
Does a gas fireplace need a blower?
Yes, you can run a gas fireplace without a blower because a blower is not part of the components of a gas fireplace. A blower is a mere appendage that you can install on your gas or even wood fireplace to enhance the heating process. If you wish to add a blower to your gas fireplace, you may have to purchase it later.
Do gas fireplaces need annual maintenance?
This is due to their relative ease of operation and cleaner burn than solid fuel models. However, this doesn't mean that your gas fireplace requires no maintenance. Because of their lower combustion temperatures, gas models often harbor spiders in the gas valve area and in the corners of the combustion chamber.
How to replace the gas control valve on your furnace?
Instructions for Replacing the Gas Valve on a Furnace
- Turn Off Circuit Breaker. Turn off the furnace's circuit breaker.
- Turn the Gas Shutoff Valve. Close the furnace's gas cock knob—the gas pipe's shutoff valve. ...
- Disconnect the Electrical Components. ...
- Position the Adjustable Wrench. ...
- Rotate the Intake Pipe. ...
- Remove the Old Gas Valve. ...
- Check the New Gas Valve. ...
- Apply Pipe Thread Compound. ...
- Connect the New Gas Valve. ...
/90445957-56a4a2965f9b58b7d0d7ef10.jpg)
How do you fix a leaking gas fireplace valve?
Often the wall shutoff valves have a packing nut on the front of the valve that works loose and causes a leak. You can use a spray bottle of water and a lot of dishwashing detergent to diclose the leak. Tighten the packing nut clockwise a bit until the leak stops.
Can you repair a gas valve?
In some instances you can repair a gas valve on a furnace depending on what is causing it to not work properly. However, repairing your gas valve is not usually the most cost effective option since it can be just as expensive to have your gas valve repaired as it would be to have your entire gas valve replaced.
How do you replace a gas fireplace key valve?
0:152:05How To Install a Decorative Key Valve Flange and Trim Ring - YouTubeYouTubeStart of suggested clipEnd of suggested clipStart by making sure the gas is off and remove the key. I'm using channel locks to loosen and removeMoreStart by making sure the gas is off and remove the key. I'm using channel locks to loosen and remove the original flange. This can scratch the flange.
How much does it cost to replace a fireplace gas valve?
Expect to pay between $150 and $300 to fix your fireplace's gas valve. The gas valve is one of the most important components in a gas unit because it controls the gas flow to the fire.
How do you know if a gas valve is bad?
Here are some signs that indicate your furnace has a bad gas valve.A Gas Leak. This is a major indicator that something could be wrong with the gas valve in your furnace. ... A Total Shutdown of the Furnace. ... A Flooded Furnace. ... Get Expert Services.
What causes a gas valve to fail?
The valve itself may have simply worn out or may be damaged due to basement seepage or submersion. Alternately, one of the electronic gas ignition components or a glitch in the safety circuit may be to blame. If your furnace has a standing pilot light, the thermocouple could be worn out.
Is it safe to leave pilot light on gas fireplace?
We recommend that you turn off your gas fireplace pilot light seasonally. Turning off your gas fireplace's pilot light can save a substantial amount of energy and money. It is important to remember that not all gas fireplaces have “standing” pilot light, or, a pilot light that is “always on”.
Where is the gas valve for my fireplace?
Gas fireplace: The shut-off for a gas fireplace is typically on the control panel. This control panel can be found behind the front screen, where a knob that controls the flow of gas can be turned to 'off'.
Can you turn on a gas fireplace without a key?
When learning how to turn on a gas fireplace without a key, see if the unit has a control panel with an igniter switch. If you're using a fireplace key and your fireplace has a front cover, remove it completely and set it aside to access the burner.
How long should a gas valve last?
Gas Valves are routinely checked for 100,000 cycles and are used in equipment that have approximately 15 years life expectancy.
How long does it take to replace gas valve?
Replacing a valve is usually a straightforward job. It becomes more time consuming as furnace access gets more difficult. Up to 1 hour | Most gas valve replacements. 1 to 2.5 hours | Valve replacements in attics, crawlspaces and similar.
How much does it cost to fix a gas valve?
Gas Valve or Smart Valve If your gas valve needs to have a liquid propane valve added during installation, the price will also be higher by about $50. Universal gas valves are cheaper than brand name valves. With all this in mind, the price for a replacement job on a gas valve ranges from $195 to $870.
How long do gas valves last?
Gas Valves are routinely checked for 100,000 cycles and are used in equipment that have approximately 15 years life expectancy.
How do you test a gas valve?
2:105:43How to test a Gas Valve - YouTubeYouTubeStart of suggested clipEnd of suggested clipNext we're going to take some jumper wires. We're going to attach them to the gas valve. Now thisMoreNext we're going to take some jumper wires. We're going to attach them to the gas valve. Now this should only be done for one to two seconds just to check the operation of the gas valve.
Can you clean a gas valve on a furnace?
Turn off electrical power and shut the furnace gas valve. Use a medium-bristled brush to sweep content off each burner and sweep out the combustion chamber as best you can. Use a straw or compressed air to blow dust and dirt off the pilot light assembly or hot surface ignitor, as well as the flame sensor.
How many steps to take when servicing a gas fireplace?
There are about 10 steps to take when servicing your gas fireplace.
What are the key components of a gas fireplace?
As key gas fireplace ignition components, thermopile and thermocouple will need to be functional at all times.
What does it mean when you hear a gas fireplace?
Certain strange sounds may be heard in your gas fireplace that points to a problem. Such may be early signs of a malfunction. You may notice your gas getting more dirty than necessary.
Why does my gas fireplace smell?
These range from dead batteries, smell of burning gas, burner failure, and release of carbon monoxide due to component failure.
What are the pilot lights on a gas fireplace?
Gas fireplaces have pilot lights that provide the necessary igniting spark for lighting fire. These lights are in the form of small blue flames located beneath the logs.
How to inspect glass when it's off?
With the glass completely off, you’ll need to inspect for scratch signs (Scratched glasses should be replaced). Using a soft cloth, clean or wipe both glass surfaces. Also, inspect all gasket fixtures on the glass.
Is a gas fireplace a problem?
Gas fireplace repair is a normal and natural response to an existing or developing problem. Fireplaces aren’t built to be problem-proof. As a matter of fact, nothing is.
WHAT WOULD CAUSE MY GAS VALVE TO LEAK?
A gas valve leak can emit natural gas or propane into the air and pose safety and environmental threats. A leak could even remain within your piping system and cause a hazard to your fire feature and gas lines/connections. Either way, a leak is never good and must be tended to immediately.
How to fix a gas leak?
For small leaks, a majority of the time this can be fixed by tightening the connection. Wipe off the solution and then tighten the fitting with a pipe wrench. Apply a new stream of the mixture and recheck. If you are still seeing bubbles and have tightened the fitting completely, you may want to have a gas professional inspect your setup.
What does it mean when gas bubbles?
Small bubbles resembling foam that form at the valve connection indicate a small leak, which is usually not a cause for major concern. Larger bubbles indicate a greater issue and should be relayed to your gas professional immediately!
Where is the ball valve located on a fire pit?
Whether you have a fireplace, a fire pit or bowl, or even a stainless steel log lighter to conveniently start a blaze in your wood-burning fire pit, chances are you have a straight or angled quarter-turn ball valve. This gas supply component is located at the end of your natural gas or propane fuel line and just before your lighter or burner. Ball valves have an interior hollowed out sphere that either blocks or accommodates gas flow depending on the position it is in. These inline valves are super easy to operate, utilizing either an easy-grip handle (shut off valve) or a valve cover and key to orient the ball 90 degrees in one of two directions:
When was the last time the Fireplace Doors Online was updated?
For inline shut off valves or units that operate with the turn of a key, Fireplace Doors Online is your one-stop source for reliable, high-quality replacement components for your gas fire feature! Last updated on September 21st 2020.
When is the best time to check gas burners?
If you have a gas-burning feature, now is the time to be proactive with some routine maintenance. Before the summer begins , it's a good idea to check for problems and get them taken care of.
Who is Selese from Fireplace Doors?
Selese is a content writer, blogger, graphic designer, and media producer for Fireplace Doors Online. She has a degree in Writing from the University of Pittsburgh and is a former Editor-and-Chief of the literary magazine, Baily's Beads. She lives in Youngsville, PA and enjoys traveling to Renaissance Faires, antiquing, and sharing random facts about Kpop music.
What to do if bubbles are present in valves?
Replace any damaged lines or faulty valves, and tighten the fittings where bubbles were present.
How to find a leak in a gas valve?
Use a gas leak detector liquid to find leaks in the supply line, valve or fittings. Apply a liberal amount of gas leak detector liquid to the supply line, valve or fittings. Slowly turn on the gas valve a half turn. If you see bubbles, you’ve found your leak. Turn off the gas valve immediately.
How to check if a spark is on an ignitor?
Check if you have a spark at the ignitor. Some ignitors operate on batteries. Unscrew the ignitor button or open the ignitor compartment and check for a battery. Replace the battery with a new one, making sure the polarity on the battery is correctly installed. Check the wire between the ignitor switch and the ignitor.
What does a fire pit thermocouple do?
Some fire pits have a thermocouple which senses the heat from the pilot light flame. That signals the gas valve to stay open when the pilot is on.
What happens if you open the tank valve on a fire pit?
If you open the valve on the fire pit before the tank valve, a safety check valve in the tank may engage, causing the fuel flow to stop.
Why does my gas line make a whistling sound?
The wrong size regulator on the supply line can result in too much gas supply and may cause a whistling sound.
What does it mean when you smell gas when the flame is not lit?
If you smell gas when the flame is not lit, you may have a leak. Turn off the gas valve immediately.
Why won't my gas fireplace turn on?
The pilot light for your gas fireplace is an ignition source. If your fireplace won't turn on, it may be a simple matter of the pilot flame having been blown out. In order to find out, simply open the vent. You will be able to determine whether or not the small flame is out.
What are the issues with a gas fireplace?
While these components of your gas fireplace system are commonly behind some of the bigger issues your fireplace may have, other issues such as needing a gas valve replacement or a gas leak require the intervention of a professional.
What is a thermocouple?
The thermocouple is a small metal rod that intersects the gas valve and the burning pilot flame. It acts as a temperature sensor and generates electricity to ignite the gas when needed.
Is it dangerous to work with gas?
Warning: Working with gas and gas appliances is dangerous. If at any point the area smells excessively of gas and you can not determine the cause, call an expert for help immediately.
Can you fix a problem on your own?
However, there are some basic issues that you can repair on your own without too much trouble. At the very least, this guide will help give you a better understanding of each problem so you can identify them more easily.
Can you fix a gas fireplace on your own?
One thing that makes fixing a gas fireplace so difficult and complex is finding the source of the issue. There could be multiple factors causing a single issue, so covering all your bases and eliminating potential culprits can be time-consuming and requires a level of expertise. However, there are some basic issues that you can repair on your own ...
How to fix a gas valve leak?
Your solution may be as simple as tightening the cap nut that you already see. Or disassemble the stem and repack with "gas valve grease". Or just puchase a new valve and replace the leaker....if it has not been mortared into the hearth!
Why do you want to repair a gas valve when replacing it is easier AND safer?
Why do you want to repair a gas valve when replacing it is easier AND safer? Cheap too. Gas valves are traditionally exposed rather than buried like water valves which are therefore designed to be maintained/ repaired.
What is going into a valve?
Going into the valve is a short piece of galvanized pipe from black pipe. Leaving the valve is black pipe. The valve itself is brass. Thanks, Dave.
When you turn the repaired valve back on, will you have to check for leaks?
When you turn the repaired or replaced valve back on you will have to check for leaks.......thoroughly !
Can gas valves be repaired?
Small gas valves are replaced, not repaired. Large valves are also replaced and then the faulty valves are rebuilt, if the valve body is not damaged. I have never seen a repair kit for anything smaller than a 2" valve. Thanks for the input, guys. I suppose I should have been more descriptive.
Is gas valve grease a solvent?
Gas Valve Grease is a function specific lubricant! "Any ol' grease" will not do the job as propane and natural gas are excellent solvents for most petroleum and organic based lubricants. You MUST buy a valve lubricant specifically designed for gas valves or you will have a valve failure!!!!!
