Method 1: Using a Barbed Coupler
- Identify the hole and cut the hose into 2 from that place.
- Pull out the inner tube from the sleeves from both ends.
- Find out which side has the hole and cut off the portion with the hole.
- Take 2 screw clams and put them over the sleeves on both sides (do not screw yet).
- Take a 1/2 inch barbed coupler, about 2.5″ long ( Check on Amazon ) and push both cut ends of the tube onto the 2 ends of the coupler
- Slide the sleeve over the coupler as much as possible and tighten the clams on the coupler.
- All done, your hose is now fixed and ready to use!
How to fix a leaking Pocket Hose?
Yeah, sounds a bit crazy, but this pocket hose mending method works. For this repair you will need E6000 Glue; Self-Adhesive tape; A razor blade (or thin paper cutter blade) Some fishing line (braided is better) and a Needle; First, cut the outer covering of the hose carefully (do not cut the inner tube) near the place where your hose is leaking.
What is a Pocket Hose?
Pocket hose is also known as an expandable garden hose or flexible hose. You will be able to fix your hose if you follow the steps below. I have researched and listed the 2 most common problems regarding pocket hoses and how to fix them. How to repair pocket hose end / nozzle leaks? Problem 2: Hole in the Hose!
How to fix a hole in a garden hose?
If it is in the hose – dry the section where you have found the hole or a cut and get rid of kinks. With thick paper tissues try cleaning the insides of the hole if possible. Then apply rubber cement but only on the top of the hole. It should not get inside the hole for that will result in a clog.
How to replace the hose on a lawn mower hose?
1 Identify the hole and cut the hose into 2 from that place. 2 Pull out the inner tube from the sleeves from both ends. 3 Find out which side has the hole and cut off the portion with the hole. 4 Take 2 screw clams and put them over the sleeves on both sides (do not screw yet). More items...
How do you fix a hole in an expandable hose?
The stretchiness of the latex material in an expandable hose makes most adhesive solutions impractical and temporary. Instead, you should excise the area of the tube with the leak and use permanent, barbed connectors to reattach the two pieces of hose together.
Can Pocket hoses be repaired?
If your expandable / pocket hose is leaking in the middle it's likely the inner flexible tube has a hole in it. But unlike a regular rubber hose, pocket hose cannot be patched up with a waterproof tape. You will need to do a little bit to work to get it fixed.
Are pocket hoses guaranteed for life?
Telebrands warrants the Pocket Hose Top Brass Bullet product, for Lifetme Replacements; discontnued products are honored up to 5 years from the date of receipt of the product by the original consumer, against significant loss of performance resultng from normal wear and tear.
How do you fix a leaky flexible garden hose?
1:524:58Repair Expandable Garden Hose - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut if you put some put some soap on it. If you cut it at a sharp angle. If you've got somethingMoreBut if you put some put some soap on it. If you cut it at a sharp angle. If you've got something that will hold it in place securely. And you use some needlenose pliers.
Can you repair a metal garden hose?
If your steel braided hose is in an area such as for a washer and dryer water supply, you can fix small leaks the size of a pinhole with nothing more than duct tape and/or common household items such as silicone caulking. Commercial hoses or those for hydraulic pressure, for example, require a coupler to fix properly.
How do I fix a leaky hose?
2:033:25How to REPAIR GARDEN HOSE in SECONDS - 3 EASY WAYS!YouTubeStart of suggested clipEnd of suggested clipOver the hose. Put the barbed fitting in the middle. And then tighten each clamp down using aMoreOver the hose. Put the barbed fitting in the middle. And then tighten each clamp down using a phillips head screwdriver. And when you're done you'll have a permanent connection that'll be snag.
Are expandable hose good for pressure washer?
The Short Answer Do not use an expandable hose between the water outlet of your pressure washer and the spray gun. The water pressure coming out of the pressure washer may be too much for the expandable hose to handle and may lead to a burst hose and a voided warranty on the pressure washer.
Is the silver bullet pocket hose safe for drinking water?
Original Pocket Hose Silver Bullet, 25-FT, 50-FT, 75-FT & 100-FT As Seen On TV, Lead-Free, Lightweight, Expanding Garden Hose Endorsed by Richard Karn, by BulbHead, Kink-Resistant, Safe for Drinking.
What is pocket hose silver bullet made of?
LIGHTWEIGHT: rubber garden hoses are such a pain to move around your garden. Pocket Hose Silver Bullet is super-lightweight and easy to maneuver around your lawn and garden....BrandPocket HoseMaterialRubber,BrassColor50 Feet
Why is my garden hose leaking?
If your hose leaks where it connects to the spigot, it's most likely caused by a worn gasket, stripped adapter, or leaking connector. Connection problems usually cost between $2 and $20 to fix.
How do I fix the end of my garden hose?
4:245:11How to Replace the End of a Garden Hose - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you choose to use the hose clamp type simply slide the mender into the inside of the hose. AndMoreIf you choose to use the hose clamp type simply slide the mender into the inside of the hose. And tighten down the clamp with a screwdriver or a nut driver. If you choose this type.
Why do expandable hoses break?
An expandable garden hose needs sufficient water pressure to work correctly. If you have poor water pressure, the garden hose won't expand correctly. Because of the materials that hoses are made from, they may be susceptible to tears and punctures.
How do you fix a silver bullet pocket hose?
0:566:50Expandable Hose (e.g. Pocket Hose) Repair Kit - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd i could actually probably repair the other end too. So the reason i stretched it out is to makeMoreAnd i could actually probably repair the other end too. So the reason i stretched it out is to make sure the inner tube and the outer sheath are at the correct length for where i cut it.
Can you fix a zero G hose?
You can repair them by just taking the fitting apart, cutting off the last two inches and then putting it back together, reusing the existing fittings. All you need is a pair of pliers and a pair of wire cutters.
Can you connect pocket hoses together?
If you have been wondering, can you connect two pocket hoses together? The answer is yes! There are several options on how you do it. One method is to use a tee fitting.
Problem 1: Leaks at the pocket hose end or valve end
If your hose is leaking at the end of the hose aka the joint where the fitting connects the nozzle or sprayer to your hose, the inner tube might have been dismantled or disconnected from the sprayer.
Problem 2: Hole in the Hose Pocket hose is leaking from the middle
If your expandable / pocket hose is leaking in the middle it’s likely the inner flexible tube has a hole in it. Pocket hose is not like regular rubber hoses and cannot be repaired with waterproof tape. You will need to do a little bit to work to get it fixed.
How to find a hole in a hose?
Identify the Hole. The easiest way to find a hole in an expandable hose is by attaching it to the spigot and turning on the water. This forces the hose to expand and will allow water to leak out of the hose where there is a hole. Some holes are large enough to be very obvious, while others are small enough so that they are harder to see.
Why do you turn the water back on after a hose is repaired?
Now that the hose has been repaired, it is necessary to turn the water back on to make sure that there aren’t any other holes and that the coupling is in place. Rather than turning the hose on all of the way, slowly turning it up is the best way to check for more holes or for a loose coupler without accidentally bursting the hose.
Why do you need to attach a hose clamp?
These clamps need to be tightened enough to prevent the hose from slipping out. Making them too tight, however, can result in accidentally cutting off the flow of water.
Can you cut through a hose?
Once the vice grips are in place then you can cut through the hose in an effort to locate the hole. The section of the hose with the hole in it will need to be cut out and thrown away, as it is important to use the coupler in a solid piece of hole so that this issue doesn’t occur again.
Can you cut a hose at an angle?
While it may be tempting to cut the hose at extreme angles to fit with the coupler, this is not the best option. An angle is important, but the angle needs to be a little shallow so that the ends of the hose aren’t at risk of popping off of the coupler once the water is turned back on.
Do you need to use tape to mark a hole in a hose?
You don’t need to use a huge piece of tape, as long as you use enough so that you can identify the hole. If the hose is a lighter color and not black, then you may be able to use a marker or pen to mark the location of the hose instead of using tape.
Can you turn off water if the hose is still on?
Once the hole has been identified and marked, then you need to turn off the water. It’s impossible to work with an expandable hose and to try to make any repairs if the water is still turned on.