
Here are 7 simple ways to fix this problem:
- Check if the fuse is working. First of all check if the fuse is working or not. ...
- Check the power cord. It is one of the most common reasons for the Kenmore electric dryer not heating. ...
- Clean the vent. ...
- Change the door gasket. ...
- Replace the thermostat. ...
- Check the drain hose. ...
- Check the circuit breaker. ...
Full Answer
Why is my Kenmore gas dryer not heating?
Why is my Kenmore dryer not heating?
- Burned or broken thermal fuse: Thermal fuses on some models have been burned. ...
- The thermostat is not set correctly: There might not be heat coming from the dryer if the thermostat is not correctly set. ...
- An obstructed vent: The vents, ductwork, and holes in your floor will be obstructed by grease and lint if they are clogged.
How to take the top off my Kenmore dryer?
- Remove the two screws on the top-rear corners of the dryer with a Phillips-head screwdriver.
- Remove the four screws on the back of the control panel with the screwdriver.
- Remove the two screws at either of the upper-front corners of the front panel with the screwdriver.
How to fix Kenmore Elite electric dryer not heating?
How To Fix Kenmore Dryer Not Heating Up Problem
- Clogged Vent. One of the most common causes for a Kenmore dryer that is not heating up problem could be a clogged vent.
- Clogged Lint Screen. If the lint screen is clogged, follow the manufacturer’s directions on how to remove it. ...
- Uneven Loads. Clothes won’t dry if they are not evenly distributed in the dryer. ...
- Blown Thermal Fuse. ...
How to repair a broken dryer heating element?
- Turn off power to the appliance or device. ...
- Disassemble the appliance or device to access the heating element, following the guides in this book for your appliance. ...
- Set the multimeter to RX1 (resistance times 1).
- Touch the multimeter probes to each end of the element.

How do I troubleshoot my Kenmore dryer?
1:4710:17Dryer Won't Start / Kenmore / What To Check and How To Fix - YouTubeYouTubeStart of suggested clipEnd of suggested clipThrough the thermal fuse indicating that the thermal fuse is actually bad one way that you can testMoreThrough the thermal fuse indicating that the thermal fuse is actually bad one way that you can test this it's not advised go ahead and connect these two leads with a jumper cable.
Is it worth it to fix a dryer?
Is it worth repairing a dryer? Dryer repairs are worth it if the appliance is less than 4 years old and the cost is less than $400. For older dryers and/or costly repairs, replacing your appliance is more cost effective.
Why did my Kenmore dryer stop working?
Always check the dryer venting when replacing a blown thermal fuse. To determine if the start switch is defective, attempt to start the dryer. If the dryer hums but does not start, the start switch is not at fault. If the dryer does not respond or make any noise, the start switch could be at fault.
How much does it cost to repair a Kenmore dryer?
Most homeowners pay between $100 and $200 for dryer repair. For example, replacing a broken thermostat costs about $150, but prices range depending on the problem....Dryer Repair Prices by Brand.BrandAverage Repair CostsKenmore$100 - $200Bosch$100 - $400GE$100 - $400Maytag$100 - $5506 more rows•Mar 30, 2022
How long do Kenmore dryers last?
10-13 yearsHow long does a dryer last? A dryer should last 10-13 years. To extend the dryer's life, clean the lint trap after each use and make sure the outer vent is clear as well. New updated information for dryer maintenance as of July 8, 2022.
Can I fix my dryer myself?
You can solve most problems yourself—no experience necessary! Most dryer problems can be fixed in an hour with a few basic tools and a continuity tester or multimeter—and you can do the work yourself with these simple instructions.
How dO I know if my thermal fuse is blown?
To test if your thermal fuse has blown, touch the right side of your multimeter lead to the right side of the fuse, and repeat with the left multimeter lead. If the multimeter needle fails to move, this indicates the thermal fuse has blown.
When I press the start button on my dryer nothing happens?
If the dryer start switch does not have continuity when it is activated, it will need to be replaced. The door switch is located near the dryer door and is activated when the door is closed. If the door switch fails, the dryer won't start at all. Most door switches will make an audible click when they are activated.
Why would a dryer suddenly stop working?
Common dryer issues include a faulty door switch or start switch and control problems such as a broken dryer timer or faulty electronic control board: Problems with the door switch can prevent the dryer from starting.
Is it better to fix a dryer or buy a new one?
You can generally repair a dryer for $125 vs replacing it for $350. Since there's little difference in life expectancy between the two options, it's generally cheaper and more practical to repair a dryer than to replace it.Is a dryer worth repairing? Yes, and here's why - The Silicon Undergroundhttps://dfarq.homeip.net › is-a-dryer-worth-repairing-yes-...https://dfarq.homeip.net › is-a-dryer-worth-repairing-yes-...Search for: Is it better to fix a dryer or buy a new one?
What causes a dryer motor to burn out?
Cleaning dryer vents and making sure the motor is not covered with lint will help prolong motor life; motors that are covered with lint are likely to overheat and burn out.Signs of a Bad Dryer Motor | Hunkerhttps://www.hunker.com › signs-of-a-bad-dryer-motorhttps://www.hunker.com › signs-of-a-bad-dryer-motorSearch for: What causes a dryer motor to burn out?
How do you know if you need a new dryer?
4 Signs That You Need a New DryerYour Clothes Aren't Drying Properly. Do you feel wet or damp areas when you remove your clothes from the dryer? ... Excessive Noise. Do you often hear a lot of noise, such as rattling, banging, or high-pitched squealing? ... It's Too Old. ... You See Exposed Wiring.4 Signs That You Need a New Dryer - Superior Air Duct Cleaninghttps://superiorairduct.com › 4-signs-that-you-need-a-new...https://superiorairduct.com › 4-signs-that-you-need-a-new...Search for: How do you know if you need a new dryer?
Is it better to fix a dryer or buy a new one?
You can generally repair a dryer for $125 vs replacing it for $350. Since there's little difference in life expectancy between the two options, it's generally cheaper and more practical to repair a dryer than to replace it.
What is the average lifespan of a dryer?
Clothes Dryer Dryers tend to last longer than washing machines, typically seven to 12 years. Make It Last: Although it's tempting to skip cleaning the lint trap between loads, a clogged trap is the top reason for stress on your dryer. Clean it every time. Skip the dryer sheets, too, according to our expert.
Is better to fix old dryer or buy new one?
If you're trying to determine whether to repair or replace your dryer, a good rule of thumb is to know the lifespan of your appliance. If the dryer is past its life expectancy, it may be cheaper to replace it versus to try to repair it.
When should you replace a dryer?
Most dryers typically last somewhere between 10-13 years, according to consumer reports. If your dryer is approaching the 10 year mark, it may be a good idea to consider replacing it even if you haven't experienced any major performance issues yet.
Most Common Problems
Start here with our troubleshooting guide to diagnose the cause of your Kenmore dryer problems. Begin by browsing the list of Kenmore dryer symptoms and once you find your match, learn more about it.
The Right Parts for the Job
We carry more than 4 million parts from over 175 major brands, so chances are, we've got the part you need.
Why is my dryer overheating?
It might seem odd that the cause of an overheated dryer would be a malfunctioning heating element. This particular dryer repair could entail a thermostat, a clogged vent, the blower wheel, or a felt seal, but many times it turns out to be the heating element. The purpose of the heating element is to send warm air to the dryer drum.
Why is my dryer heating at one temperature?
If your dryer seems like it’s heating at one temperature and that temperature has been charring your clothes, there is a high probability that the heating element has shorted out and needs to be replaced .
What is the purpose of a heating element in a dryer?
The purpose of the heating element is to send warm air to the dryer drum. When the element shorts out, the result is a continuous flow of heat in spite of the dryer reaching the proper temperature.
How to check continuity of blower duct?
Remove ¼ inch screws that secure the blower duct in place. Set the multimeter to ohms to check continuity. Remove the two wires that connect to the heating element located to the left of the blower duct. With your multimeter place one probe on either terminal and ground the other probe.
Why is my Kenmore dryer not heating?
One of the most common issues with a Kenmore dryer that is not heating, is that the heater element has gone bad. The heating element in a dryer is supposed to warm the air before it enters the dryer. You may need to replace the heating element if your dryer isn’t producing enough heat or if the drying time has been increased significantly.
What does a flame sensor do on a Kenmore dryer?
On gas dryers, a flame sensor detects the heat from the flame. If the sensor goes out, the dryer won’t work. If your Kenmore dryer isn’t heating, don’t assume the flame sensor is defective. First, check to see if the igniter and thermal fuse are bad. If you’ve ruled out those causes, test the flame sensor for continuity at room temperature with a multimeter. If there’s no continuity present, replace it.
How to test if a dryer is heating?
Yet another way to test your dryer’s heating element is by unplugging the device and disconnecting the two wires of your thermostat. To provide heat for the dryer, you’ll need to join these wires using electrical tape. Now that the thermostat has been bypassed turn the dryer back on. If it heats, you know for sure the thermostat is telling it not to heat up, and you need to replace it.
What is the igniter on a gas dryer?
The igniter is a necessary component of the gas dryer. If it does not work, then there will be no heat, and you’ll have to spend your time on laundry hanging out in wet clothes instead of drying them off good! Luckily for us all, testing for continuity with an old-fashioned multimeter can tell if this important part needs replacing or just some new spark plugging up its works.
How to tell if dryer heating element is working?
To figure out if your dryer’s heating element is working, you need to test it . To do this, you can use a multimeter and measure the resistance of the heating element. If it doesn’t provide at least 15 ohms of resistance, then your heating coil needs to be replaced.
What happens if a lint screen is clogged?
If the screen is clogged, your clothes won’t dry properly and will take longer to dry than normal.
Why won't my clothes dry?
Clothes won’t dry if they are not evenly distributed in the dryer. Load them as close to each other as possible, and try rotating clothes 180 degrees halfway through the drying time, so both sides get exposed to heat from the moving air.
How to tell if a gas dryer is defective?
If a solenoid fails, the burner may run intermittently. If the burner keeps shutting off, the dryer won’t heat properly and may not stop. To determine if one or more of the gas valve solenoids has failed, check the igniter. If the igniter glows and goes out but does not ignite the gas, the gas valve solenoid is defective. If one or more of the gas ...
Why does my dryer take so long to dry clothes?
If the blower wheel is obstructed or defective, it may take too long to dry clothes. To determine if the blower wheel is working properly, remove the dryer vent and assess the strength of the air fl...ow. If the air flow is weak, check the blower wheel for obstructions.
What is a gas dryer solenoid?
03 - Gas Valve Solenoid. Gas dryers have two or more gas valve solenoid coils. The gas valve solenoids open the gas valve ports to allow gas to flow into the burner assembly. If a solenoid fails, the burner may run intermittently. If the burner keeps shutting off, the dryer won’t heat properly and may not stop.
How to check if blower wheel is weak?
ow. If the air flow is weak, check the blower wheel for obstructions. If no obstructions are present, try rotating the blower wheel by hand . If the blower wheel wobbles as it turns, replace it.
What happens if the belt on a dryer is broken?
The rollers must spin freely to work properly. If the drum rollers are worn out, the dryer won’t turn properly.
How to tell if dryer drum bearing is worn out?
To determine if the drum bearing is at fault, remove the dryer belt and try turning the drum by hand. If the drum rotates freely, the drum bearing is not likely worn out.
What happens if the drum glides on a dryer are worn out?
If the drum glides are worn out, the drum can start binding and put strain on the motor. If this happens, the motor shuts down, preventing the dryer from turning. To determine if the drum glides are worn out, inspect them for wear. If one or more of the... glides are worn out, replace all of the glides as a set.
How to tell if support rollers are worn out?
To determine if the support rollers are worn out, remove the belt from the dryer and try turning the drum by hand. If the drum does not... rotate freely, check the support rollers for wear. If the rollers spin freely without wobbling, they do not need to be replaced.
How many rollers does a dryer have?
Most dryers have two drum rollers on the rear of the drum, and some dryers have two more rollers supporting the front of the drum. The rollers must spin freely to work properly. If the drum rollers are worn out, the dryer won’t turn properly.
Why does my dryer stop mid cycle?
If the drum bearing is worn out, it may put too much strain on the motor, causing the dryer to stop mid-cycle or not turn at all. To determine if the drum bearing is at fault, remove the dryer belt and try turning the drum by hand. If the drum rotates freely, it is unlikely that the drum bearing is worn out.
How to fix a humming motor?
First, check the motor to see if it makes a humming noise. If the motor still hums, remove the belt from the motor and check the blower wheel to ensure that it is not obstructed. Next, with the belt removed, try rotating the drum by hand. If the drum does not rotate freely, determine what is causing the drum to bind.
Most Common Problems
Our dryer troubleshooting guide walks you through the repair steps from diagnosis to part selection to fixing the problem. We even have videos to help you along the way. Think of it as a pathway to perma-press success.
The Right Parts for the Job
We carry more than 4 million parts from over 175 major brands, so chances are, we've got the part you need.
