how to repair a pool motor

There are some options for you, including a pump union or CPVC fittings. On the other hand, if the fitting is not too loose, you can repair it. Apply Silicone or Pool Putty and keep the pump running for 24 hours, your fitting will be hardened.

Full Answer

How to maintain and service your swimming pool?

Steps

1. Scoop leaves out of the pool. If leaves are left to settle at the bottom of your pool for too long, they'll break down and stain the bottom of ...
2. Brush the pool. After scooping the leaves, brush the floor and sides of your pool. ...
3. Vacuum the pool. ...
4. Test your pool water. ...
5. Adding chlorine to the pool. ...
6. Tip for salt water pools. ...

How to service your own swimming pool?

Off-Season

• Inspect the pool before you close it for the season. ...
• Test the water’s chemical levels and adjust accordingly. ...
• Remove all objects from the pool. ...
• Drain all water from the pool’s pump, filter, heater and all associated tubing. ...
• Lower the pool’s water level by draining the water into the local sewer lines. ...
• Cover your pool with a pool safety cover. ...

More items...

How to Prime your swimming pool water filter motor pump?

Steps to Prime Your Pool Pump

• Turn off the pump. ...
• Switch to recirculate. ...
• Release air. ...
• Clean out the pump basket. ...
• Fill the pump basket. ...
• Once the pump basket is filled and tightened, make sure the air release valve is open and turn the power to the pump on.
• Check the water flow to your pump. ...
• Once the water is constantly flowing, close the air pressure release valve.

How do you repair a leak in a pool?

Repairing Your In-ground Swimming Pool Main Drain Pipe

• Diagnosing Leak In Main Drain. First thing you need to do, is verify that your main drain line is leaking. ...
• Repair Difficulty Level. This is an easier repair than you might think. ...
• The Most Common Reason For Leak. ...
• Finding The Leak. ...
• Repairing The Line. ...

Can a pool pump motor be repaired?

Most of the new generation of pumps are already equipped with automatic controls and safety features. In fact, if you take enough time to learn the manual, you might find yourself able to repair some of the problems on your own. Of course, there are repairs and replacements are best left in the hands of professionals.

How do you fix a broken pool pump?

1:194:58POOL PUMP Not Working? How To Fix 6 Common Pump ProblemsYouTubeStart of suggested clipEnd of suggested clipIf you have a leaky pump look for any seals that need replacing like the o-rings in the impeller.MoreIf you have a leaky pump look for any seals that need replacing like the o-rings in the impeller. Housing the thread sealant or the shaft seal.

How much does it cost to rebuild a pool pump motor?

A replacement motor is generally going to cost you in the neighborhood of $150 – $300 depending on the horsepower. Add another $15 – $30 for the absolutely necessary, non-negotiable new shaft seal.

How do I know if my pool pump motor is bad?

Your pump could be leaking water, or the bearings might need to be replaced instead of the entire motor. Screeching is also a sign that your motor bearings need to be replaced. These loud, often painful sounds could also be a sign of rust or oxidation, making it more difficult for the bearings to do their job.

How much does it cost to replace a pool motor?

Pool Motor Cost A new pool motor costs $300 on average, with most models ranging from $100 to $500 (materials only). If your pool pump stops working, you might only need to replace the motor instead of the entire system.

What causes a pool pump to stop working?

It could be something blocking it, a dirty pool filter, or too much air in the system. If there's something blocking your pump's suction, check your filter gauge. If it's 10psi above the normal reading, clean your filter. This will reduce pressure and reset your pump's flow.

How long do pool pump motors usually last?

eight to 12 yearsOn average, pool pumps last eight to 12 years before needing replacement. Over time, it's normal for pool parts to begin to wear down. In addition, swimming pool technology has come a long way in the last decade.4 Signs It's Time To Repair Or Replace Your Pool Pumphttps://www.alwaysclearpoolcleaning.com › blog › 4-sign...https://www.alwaysclearpoolcleaning.com › blog › 4-sign...Search for: How long do pool pump motors usually last?

How do you rebuild a pump motor?

4:5411:43How To Rebuild And Install A Pool Pump Motor - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's time to start reassembling the pump and I'm just putting a little wherever. There's a gasket orMoreIt's time to start reassembling the pump and I'm just putting a little wherever. There's a gasket or o-ring I'm putting a little bit of that pump lube. And we're putting on the first plastic piece.How To Rebuild And Install A Pool Pump Motor - YouTubehttps://www.youtube.com › watchhttps://www.youtube.com › watchSearch for: How do you rebuild a pump motor?

Is it difficult to replace a pool pump?

A professional electrician will be needed to disconnect the wiring before a pump can be removed. Once a new pump is installed, an electrician will again be necessary to reconnect the wires to the new pump. A do-it-yourself homeowner with basic mechanical aptitude can replace the pool pump in a relatively short time.How to Replace a Pool Pump - Home Guideshttps://homeguides.sfgate.com › replace-pool-pump-59285https://homeguides.sfgate.com › replace-pool-pump-59285Search for: Is it difficult to replace a pool pump?

How long should a pool pump last?

eight to 12 yearsOn average, pool pumps last eight to 12 years before needing replacement. Over time, it's normal for pool parts to begin to wear down. In addition, swimming pool technology has come a long way in the last decade.

How do you replace a pool pump motor?

0:028:41How to: Replace a Pool Pump Motor - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst is remove the pool pump motor from the pump housing. Second is to take the bonding wire offMoreFirst is remove the pool pump motor from the pump housing. Second is to take the bonding wire off and third is to take the electrical off the back of the pump.

What causes a pool motor to short out?

It is often caused by something melting or shifting just enough to contact something it shouldn’t. It can also be caused by the introduction of a conductive element that gets stuck in a position that allows it to ground out a portion of the motor. When a pool motor gets shorted out, there’s not much you can do. In the vast majority of cases, the component will be too hard to locate and too time-consuming to repair. Even if you do repair it, there may be another problem that caused it, which will result in the problem repeating itself.

Why does my pool motor make noise?

Because one or more of the bearings is worn or broken, the spinning motion combined with a motor shaft that can now move out of place causes excess friction, and that rubbing creates no ise. If the bearing is replaced, the friction stops because the shaft is now held in the proper position—centered by the bearing. A bearing is a relatively inexpensive part and one of the easier facets of pool motor repair. You can even do this yourself with some fairly simple tools and a good amount of time and patience. However, if you’re short on either, it is better (and safer) to get a professional to handle it for you.

How does a pool pump impeller affect the pump?

Bearing failure doesn’t mean the pump will stop spinning. It can continue to spin, driven by the electric motor. The problem is that if the bearings are not holding the shaft properly in place, the impeller can rub against the sides of the housing. This can cause the impeller to wear and affect circulation and noise inside the pool pump. A chipped or clogged impeller will affect your pool pump in several different ways. First, it will make the pumping action less efficient. A clogged or broken impeller will negate the pressure that is supposed to be created by the spinning of the impeller. This will cause less water to be drawn into and pumped throughout the system.

What is the difference between a pool pump and a lawnmower?

One of the main differences between your pool pump motor and your lawnmower motor is (unless your lawnmower is electric), your pool pump motor is simpler in design and has fewer moving parts. However, these parts have to all move in sync, and even the slightest malfunction can spoil the entire system. Here’s a basic breakdown of your pool pump motor and parts which may need repair in the event of a malfunction:

How does an electric motor work?

An electric motor is a relatively simple machine. Imagine a magnet sitting on a table with the positive side facing you. If you put a negatively charged magnet near it and to the right, where will the magnet move? Yeah, to the right. If you removed that and then put it slightly more to the right, the magnet would turn towards it accordingly. That’s how an electromagnetic motor works, as well.

Why do bearings fail?

If something gets lodged in the impeller—even for a moment—or if it nicks the impeller, throwing it momentarily out of place, the bearing can be damaged. This is because the shaft that spins the impeller is allowed to do so by the bearings . It is also held in a central position by the bearing.

Why do pool pumps need to be replaced?

The most common reasons that a motor would need to be replaced include failed bearings, corrosion inside and/or outside the motor, failed start and run capacitors, and motor age.

How to secure a pool pump?

Bring reassembled motor and rear of pump to pool area and slide the motor and rear of pump into the pump housing. Secure the seal plate to the pump housing using the clamp assembly or 9/16” bolts.

How to remove a pump from the housing?

Depending on the pump model, remove the clamp assembly or 9/16” bolts holding the seal plate to the pump housing. Carefully remove the motor and rear of the pump from the pump housing and place it on a table or workbench.

What size wrench to use for a motor shaft?

Use the 7/16” wrench or appropriate size wrench to hold the rear of the motor shaft and prevent motor shaft rotation.

How to stop a pump from causing unintended operation?

Shut off power to the pump at the breaker to prevent unintended operation of equipment and for safety precautions. Remove the electrical whip from the rear of the motor. Using tape and a pen, mark the hot, neutral, and ground wires.

Do you turn off power before replacing a pump?

Make sure the power to the pump is turned off before beginning the replacement.

How old is a pool pump motor?

Another thing to weigh out is the age of the motor and if it’s worth investing any money into it. Age is relative to where you are located. A pump running 365 days a year in warmer climes is going to be “older” than the same pump with the same installation date in a colder region where pools are closed most of the year. So if it’s over 2 – 3 years old in the Sun Belt or 5 – 6 years old up north, most likely it will not pay to repair it. Many pool pump motors last less than 5 years; the last thing you want to do is put $100 worth of repairs into a motor that was destined to die in 6 months anyway. Plus none of your replacement parts will carry a warranty whereas a complete new motor will.

How much does it cost to replace a pump motor?

Assuming you are out of warranty, you have a decision to make. A replacement motor is generally going to cost you in the neighborhood of $150 – $300 depending on the horsepower. Add another $15 – $30 for the absolutely ...

How to check if a pump is still under warranty?

The first thing to check is if it’s still under warranty. For a pump that still has the original motor, you would contact the manufacturer of the entire pump. If you have already replaced the motor before, you would contact the manufacturer of the motor .

Can you repair a pool motor?

Is it the capacitor, the bearings, an electrical short? If you’re mechanical and handy and know your way around a pool pump, then it could be fairly easy for you to diagnose the issue and even repair it yourself.

Can you replace a motor in a pump?

The bottom line – I believe in general you will get more value and longevity out of replacing the complete motor. Motor replacement also presents you with the opportunity to upgrade to a more energy efficient system – perhaps a lower horsepower if your pump is over-sized as so many are, or a dual speed or variable speed. In many cases, you can easily recoup your motor expense through energy savings. To get an idea of variable speed pump savings, try Pentair’s Savings Calculator. This calculator is based on their IntelliFlo pump but will give you a general idea of energy efficiency’s impact on your wallet.

What happens if a motor stops cold?

If your motor stops cold in its tracks then it is likely overloading the circuit or tripping a thermal fuse. Both a big no-no and should be avoided if you want a long lasting motor.

Why is my motor throwing up smoke signals?

If your motor is throwing up smoke signals or randomly switching off then on again, then it is likely a victim of overheating . This How-To guide will help you pinpoint the issue and stop the break in your filtering schedule .

Why does my motor sound like a freight train?

If you motor sounds like a freight train screeching to a stop then your bearings have likely gone bad. Caused by a leak from the shaft seal or water introduced to the motor’s shaft system elsewhere; either way you’re neighbors will hate you until it is fixed ( Part 1, Part 2 ). This guide also covers some other noisy nuisances that can trouble your motor.

Can an electric pool motor have a false start?

Just like their gas powered cousins, electric motors can have false starts as well; luckily, they are pretty easy to diagnose and fix. It could be a capacitor or something deeper; read the guide to find out what is gumming up your motor. How to Guide: How to Troubleshoot Pool Motor Not Starting.

What to do if your pump looks damaged?

If it looks damaged, it may need to be replaced. Once you have checked these, you should also check the pump impeller for any clogging. Once all of these things have been taken care of, you'll probably then need to prime the pump to get it going again. 3.

Why does my pool pump vibrate?

Cavitation happens when your pool pump is starving for water.

Why isn't my pump basket filling up?

The pump basket isn't filling with water. If your pump basket isn’t filling up with water, the problem is probably that the pump is sucking air somewhere just like we talked about in #5. But it could also be a dirty or clogged filter or pump basket.

What causes a pump to leak?

Most of the time, the issue with a leaky pump (usually a pressure-side leak) is a bad o-ring in the impeller housing, bad shaft seal, or a bad thread sealant.

Why is my pool pump not pumping?

The pump runs, but isn't pumping. In this situation, something has interrupted the suction or the water flow that causes the system to work properly. In other words, it has lost its prime. This could mean an obstruction, dirty pool filter or too much air getting into the plumbing system.

How to tell if a pump is leaking?

If there is a leak under the shaving cream, you'll start to see one area of foam start to pit as it gets sucked in.

Why does my pump make a noise?

The pump is making a lot of noise. If your motor sounds a little off, it could be a problem. You’ve probably gotten used to its regular grumblings, so you know when the sounds are different than normal. If it sounds a little like one of those old vibrating beds in a cheap hotel, the problem could be cavitation.