Hold the recoil starter firmly--it is still under tension--and remove the screwdriver. Pull the starter cord tight and then let go of the pulley. Control the rope speed as the pulley winds the rope back into the starter.
What causes a recoil starter to fail?
Your recoil starter may also fail because the pulley or recoil housing has worn and the spring no longer sits in the housing correctly. We used a Briggs and Stratton starter for this repair, but most starters will require the same steps. Visit our Briggs and Stratton parts page to find the right parts for your Briggs and Stratton starter.
How to replace a broken recoil starter housing?
Remove the recoil housing cap Unscrew the cap that holds the pulley to the recoil starter housing. If your spring has slid out of the slots in the housing, then you can continue with the repair. If the housing, pulley or spring have failed, then you will need the proper replacement parts before continuing. 2. Untie the rope
How do you coil a recoil starter on a lawn mower?
7. Coil the cord Hold the recoil starter firmly--it is still under tension--and remove the screwdriver. Pull the starter cord tight and then let go of the pulley. Control the rope speed as the pulley winds the rope back into the starter.
How do you remove a starter from a Briggs and Stratton mower?
If your mower has a Briggs & Stratton engine, you simply need to remove the screws holding the starter to get it off the engine. Turn the starter over; unwind what's left of the old rope from the pulley and pull the knot out of the notch in the hub.
How do you fix a recoil spring starter?
0:050:56How to Rewind a Recoil Starter Spring--A Quick Fix - YouTubeYouTubeStart of suggested clipEnd of suggested clipIn first I just align the tab on the spring with the notch and the housing. And then I just wind theMoreIn first I just align the tab on the spring with the notch and the housing. And then I just wind the spring back into the housing. And that's how simple it is to rewind a starter spring.
How do you fix a small engine recoil starter?
1:334:37How to Fix the Start Recoil on a Lawnmower - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd simply cut the knotted end off. Then pull the rest of the rope away from the pulley. Now I wantMoreAnd simply cut the knotted end off. Then pull the rest of the rope away from the pulley. Now I want to remove the screwdriver again being careful to not allow this to recoil back.
How do you fix a pull start that won't retract?
0:412:58HOW-TO Tighten A Limp Starter Rope That Won't Retract On A Small EngineYouTubeStart of suggested clipEnd of suggested clipI'm just going to turn counterclockwise. One turn on this one if the rope was out further I would goMoreI'm just going to turn counterclockwise. One turn on this one if the rope was out further I would go two turns counterclockwise. And with this recoil here one turn counterclockwise fix.
How do you fix a recoil starter on a lawn mower?
0:171:19Replacing the Recoil Starter on a Lawn Mower - YouTubeYouTubeStart of suggested clipEnd of suggested clipPosition the new recoil starter in the blower housing and snap it into the retainer clips snap theMorePosition the new recoil starter in the blower housing and snap it into the retainer clips snap the recoil starter guard into place position the blower housing on top of the engine.
How do you replace the recoil spring on a Briggs and Stratton engine?
1:343:54Briggs & Stratton Lawn Mower Spring & Pulley Replacement #498144YouTubeStart of suggested clipEnd of suggested clipNow transfer the ratchet balls from the old pulley to the new. One position the friction plate andMoreNow transfer the ratchet balls from the old pulley to the new. One position the friction plate and tighten the bolt rotate the pulley counterclockwise approximately five times to tighten the spring.
How does a recoil spring work?
1:253:52Chainsaw Recoil Spring (How it Works) - Understanding for RepairYouTubeStart of suggested clipEnd of suggested clipIn this direction the more the pulley turns the more tensions being put on that spring you can seeMoreIn this direction the more the pulley turns the more tensions being put on that spring you can see that by the spring coils getting smaller and smaller as more tension is loaded onto them.
How do you tension a starter spring on a lawn mower?
0:163:31How to Tension a Lawn Mower Starter Spring - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt think of which way you pull in the rope. So that you wind it the right way. And you wind the ropeMoreIt think of which way you pull in the rope. So that you wind it the right way. And you wind the rope wind the string. In you're tensioning the spring.
Why does my pull cord get stuck?
Problems With the Recoil Mechanism Sometimes the pull cord crosses over itself when rewinding, and when this happens, it can get stuck. You may be able to free it by pulling it gently to coax it out to its full length, then letting it rewind slowly.
How do you lubricate pull start?
3:535:41How To Lubricate A Sticky Starter On A Chain Saw or Weed EaterYouTubeStart of suggested clipEnd of suggested clipRight I usually go on the top when I put a couple good blasts in the in the top in the hole that'sMoreRight I usually go on the top when I put a couple good blasts in the in the top in the hole that's closest to the top blast. It in there like that.
What is the thing you pull to start a lawn mower called?
recoil starterThe recoil starter is the pull-start mechanism on the back of the engine that enables you to start your snow blower or lawnmower. The starter cord is also called a starter rope.
How to replace a spring on a recoil starter?
1. Remove the recoil housing cap. Unscrew the cap that holds the pulley to the recoil starter housing. If your spring has slid out of the slots in the housing, then you can continue with the repair. If the housing, pulley or spring have failed, then you will need the proper replacement parts before continuing. 2.
How long does it take to fix a recoil starter?
Luckily, when this happens, you can fix your recoil starter in about 20 minutes. Your recoil starter may also fail because the pulley or recoil housing has worn and the spring no longer sits in the housing correctly. We used a Briggs and Stratton starter for this repair, but most starters will require the same steps.
How to keep a pulley from spinning?
With the pulley in the recoil housing, turn it about six times. Once you have tensioned the spring, use a small screwdriver to keep the pulley from spinning. 5. Attach the cap. Reattach the cap that holds the pulley to the recoil housing.
How to fix a broken starter?
Coil the cord. Hold the recoil starter firmly--it is still under tension--and remove the screwdriver. Pull the starter cord tight and then let go of the pulley. Control the rope speed as the pulley winds the rope back into the starter. Conclusion You can easily repair a broken small engine recoil starter yourself.
Why does my lawn mower's recoil starter fail?
In most cases, the recoil starter fails because the spring slides out of place, causing it to lose tension. Luckily, when this happens, you can fix your recoil starter in about 20 minutes. Your recoil starter may also fail ...
Can a small gas engine recoil starter be repaired?
As anyone who works with lawn equipment knows, small engine recoil starters eventually fail.
Which mowers have recoil starters?
Many lawn mower companies, including Craftsman, Toro and Murray, equip their products with Briggs & Stratton engines, and all of these have recoil starter assemblies.
Where is the starter on a lawn mower?
Moreover, if you have an older lawn mower, the starter may be riveted to the engine housing .
How many screws are in a starter housing?
Examine the engine configuration. You may find three or four screws holding the starter housing to the engine. If so, unscrew them with a screwdriver and lift the starter off the engine.
