
How to Properly Repair a Surfboard
- Cut and clean the damaged part. The first step in repairing your surfboard is to cut and clean the damaged part using a razor blade. ...
- Start sanding down your board. The next step is to sand down your surfboard. You might want a smoother surface to work with when repairing your board. ...
- Start filling the gaps. When you’re confident that you have adequately cleaned the board, proceed to fill the gaps. ...
- Sand it down. Once the mixture that you used in filling the gaps hardened, sand it down. This way, it falls flat with the board. ...
- Start glassing the repaired area. You will need two circular fiberglass pieces; just make sure that the other one is a bit bigger compared to the other, and both ...
- Sand the area again. After placing two pieces of fiberglass, you may now sand the area again. ...
- Add finishing coat. After sanding and smoothing it down, make sure to add a thin layer of resin and final drops of catalyst to the mixture. ...
- Wait for 48 hours before using the board.
How to fix a hole in a surfboard?
The basic steps that will be covered are:
- Cut out the bad section of the board, in this case a large blister
- Gluing back the fiberglass that was cut out (in this case I was able to save the fiberglass blister as it was very structurally sound)
- Sanding rough the repair area
- Adding a fiberglass patch or the repair area
How to repair a buckled surfboard?
Fix a Very Broken Surf Board: Graft it back together and fiberglass it invulnerably strong. This project is good preparation for making a board from scratch.This repair method uses epoxy resin and microballoon putty. Instead of epoxy you could use polyester resin or vinyl ester …
How to repair your boat or surfboard?
- Make sure this fits by entering your model number.
- ⬛ GRADE A-True Composites is a renowned name for its premium product used in the marine industry!
- ⬛ FLAT non-crimped fiber sheet yield reduced print-thru & higher stiffness than woven fabric!
- ⬛ APPLICATION: For every yard of 50" 1708 Biaxial Fiberglass, it takes about half gallon of resin!
How to clean a surfboard?
How To Clean A Surfboard? Allow the old wax to melt off the surfboard with a stick of wood, but do not let it linger out in direct sunlight longer than five minutes. The wax comb (or a worn out old credit card) is best for removing soft wax. With a clean cloth, wipe both sides of the board with a citrus-based surfboard cleaner (or coconut oil ...

What can I use to repair a surfboard?
A traditional surfboard repair kit includes:resin.hardener.fiberglass cloth patch.Q-Cell Filler.sandpaper.cups.application tubes.mixing sticks.More items...•
Can a surfboard be repaired?
While it's true that repair specialists will always do a better job at repairing your surfboard, you don't really need their help when it comes to fixing a minor ding. You can save a lot of money doing it on your own, not to mention save yourself from the hassles of waiting for weeks for the repair to finish.
Can you fix a chipped surfboard?
Surfing is a fun and exhilarating experience, but most surfers know that your board can take a lot of hits during a long day on the waves. If you notice a crack in your board, don't worry! You can repair most cracks at home as long as you clean the area, properly apply and cure the resin, and smooth the board.
How do you fix a hole in a surfboard?
3:058:06How To Fix A Hole in a Surfboard - HOWTO Episode 1 - YouTubeYouTubeStart of suggested clipEnd of suggested clipThrough all the foam and resin. Make sure you get it off all the edges too because sometimes you canMoreThrough all the foam and resin. Make sure you get it off all the edges too because sometimes you can mix it up really well but misfits on the edge.
How much does it cost to restore a surfboard?
GLASS LAB 2019 DING REPAIR PRICE LISTPUEPSREBUILD TAIL$100$130GLASSED IN FIN$130$150FCS original Plug$75$952nd FCS original Plug$55$7514 more rows
How do you refurbish an old surfboard?
18:3126:01How to repair an old surfboard - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd we're gonna mix it with a thing called micro balloons and micro balloons a type of fillerMoreAnd we're gonna mix it with a thing called micro balloons and micro balloons a type of filler similar to like the filler we used in the previous steps.
How do you fix a split in a surfboard?
1:4822:01How to Fix a Surfboard - Cracked Rail Ding with Color Match - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is called arrow sill. I'm in used it before but it looks similar to some of the other fillers.MoreThis is called arrow sill. I'm in used it before but it looks similar to some of the other fillers. And you know things that will lighten resin I've heard of even people using sugar and sugar.
How do you fix spider cracks on a surfboard?
1:134:57How to repair cracks in your surfboard - YouTubeYouTubeStart of suggested clipEnd of suggested clipSimply cut around the dotted lines three sides peel open the mini pack remove sugru need in yourMoreSimply cut around the dotted lines three sides peel open the mini pack remove sugru need in your fingers for a few seconds. And you're good to go top tip for this repair.
Can I surf with a ding in my board?
Leaving dings or cracks can allow water to get into the board causing the board to get waterlogged. If you continue to surf on a board and not fix the ding over a long period of time the water will cause the fiberglass to delaminate from the foam causing serious damage to the integrity of the board.
How do you repair a fiberglass board?
3:5310:23Surfboard Ding Repair Tutorial - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can see we're blending right there the flat block and the 40 grit does a really good job toMoreYou can see we're blending right there the flat block and the 40 grit does a really good job to taking off material. Quickly. Now we're going to press the area for lamination.
Can you duct tape a surfboard ding?
The Duct Tape Method Slap a patch of tape over your ding for instant waterproofing. It's great to keep a roll of it in your car, in case you ding your board on the way to or from the beach, and you still want to surf without worrying about waterlogging the board.
How do you tell if your surfboard is epoxy or fiberglass?
How do you tell epoxy from regular boards?, Well to start with look at the manufacturers logos (the “stickers” under the glass work), most reputable board builders will put the word epoxy on most or at least one of these, so READ them all first, if you find the word epoxy on any of these than it is an epoxy… as for the ...
How to fix a fiberglass blister on a surfboard?
The fiberglass patch that was cut out was able to be salvaged as it was in excellent shape, however it was convex in shape so it needed to be flattened before being glued back to the surfboard. Using a heat gun the blister was heated gently until it flattened out, a block of wood was used to help keep it level.
What is the last step on a surfboard?
The last step and is optional is polishing, polishing will help blend the repair area in with the rest of the surfboard. I like using an automotive clear coat polish. I use a cloth and apply a little polish and start working at the surfboard, it will take some elbow grease! You can also use a buffer if you have one and will speed things up.
How to soak fiberglass in epoxy?
Using an automotive body filler squeegee, move the epoxy around the board giving it time to soak into the fiberglass. Don't rush this, let the fiberglass get saturated.
How to repair fiberglass blisters?
Determine the area that needs to be repaired and remove the fiberglass. Using a marker the blister was marked where it separated from the foam. Then using a rotary tool with a cutting disc the marked area was cut out, a vacuum was used to keep the dust down while cutting. Don't forget to wear a dust mask to keep the fiberglass dust out of your lungs.
What to do with a blister on a board?
Cut out the bad section of the board, in this case a large blister
How to get rid of dust on epoxy board?
Vacuum to get rid of any dust, avoid touching the board with your hands as they have natural oils that can contaminate the surface causing adhesion issues with the epoxy.
Why do you put tape on epoxy?
Some tape was applied to keep the epoxy off the parts of the board that were not being repaired.
How to repair a ding on a surfboard?
Step 1: Cut it Out. The first thing that you must do it remove the damaged part of the board by cutting out the ding with the razor blade provided. This will help to remove any part that has broken, crushed, or rotted.
What to do if you snapped your nose on a surfboard?
In the unfortunate event that you have snapped off your nose or there are serious gashes in the fiberglass and foam, your best option is to take the board to the local surf shop and see what they can do.
What materials are needed to repair a ding?
The materials that can usually be found in a ding repair kitinclude sandpaper, fiberglass, masking tape, mixing cup, sanding resin and catalyst, acetone, safety mask, wax comb, razor blade, paintbrush, safety glasses, and Q-cell filler.
What is the last step in sanding a board?
The last step involves a process known as wet sanding. What you’ll need to do is provide a little bit of water to the surface and then use sand paper, sanding in slow circular motions. A paste will develop on the sandpaper and any remaining resin can be washed off the board.
How to smooth out fiberglass?
Pour some of the resin on top of that fiberglass layer and spread out the coating evenly, making a smooth surface. Finally, apply the smaller of the fiberglass sheets in the same manner and once again, pour on resin, ensuring that the coating is smooth.
Why is it important to learn to use a ding repair kit?
Learning to use a ding repair kit might possibly be as important as learning to stand up for your first time. Not only does it prevent you from having to drop off your surfboard at the shop and wait for them to repair it, but you’re also going to save money on a price tag that is certainly not going to be easy on your wallet.
How to get rid of wax on surfboard?
Initially, you will need to use the wax comb to get rid of any wax that is around the area you cut. To make sure that it’s a clean surface around the cut, pour some of the acetone on it to help breakdown any other substances that might still be on the board (check out the article on how to clean your surfboard).
What is needed for a surfboard repair kit?
This simple surfboard repair kit comes with everything you'll need to be using when it comes to basic surfboard repairs; fiberglass cloth, UV resin, and a pad to help you sand.
What podcast covers surfing?
That wraps up this article. If you are more of the audio type, take a look at our friends surfing podcast, which covers traveling, tips, tricks and all things surfing.
What do squeegees do to resin?
Squeegees help spread resin evenly and smooth, which will help immensely once it comes time to sand.
Can you go wrong with duct tape?
Cannot go wrong with a roll of duct tape. It provides a temporary solution to keeping any dings watertight while traveling and it works wayyyy better on reef cuts than any waterproof bandaid I've ever encountered.
Can you use fiberglass cloth for surfboard ding repair?
Any surfboard ding repair that's done right will have used fiberglass cloth (because resin by itself is brittle). That means take the initiative to invest in a sharp pair of quality shears to cut cloth with; as it will dull out those cheap scissors you bought in the arts and crafts section at Walmart faster than wax on a black board melts under a tropical sun.
How to repair a cracked surfboard?
To repair a cracked surfboard, clean and dry the board, and remove any rotten foam from the cracked area. Sand the crack until the fiberglass layer is exposed . Then, fill the crack with a UV-activated resin, and cover the resin with clear plastic before setting the board in the sun for 5-10 minutes.
How to fix a crack in a fiberglass board?
Sand the crack with rough grit sandpaper down to the fiberglass cloth. Rub a rough sandpaper over the crack in the board, sanding an area slightly larger than the crack. Once the fiberglass cloth under the outer coating of the board becomes visible, stop sanding.
How to get rid of resin on a board?
Start sanding with a rough grit sandpaper to remove larger bumps and imperfections in the resin. Then, switch to a finer grit to smooth the resin to match the board. Once the resin is smooth, wipe away the debris and make sure the edges of the resin are flush with the rest of the board.
How to replace rotten foam?
Make a mixture of resin and Q-Cell filler to replace rotten foam. Q-Cell filler acts as a replacement for the foam because it expands when it cures. Pour 1 fluid ounce (30 mL) of resin into a cup and slowly add the Q-Cell filler until the mixture is the consistency of toothpaste.
How to fix cracks in a wood board?
Use a wooden stick or spoon to apply resin liberally over the crack. In a covered area out of the sun, squeeze the resin into the crack first, and then smooth the resin over the crack. Make sure the resin is touching the outer shell of the board.
How to remove rotten foam from a board?
Look for brown or black foam that is soft to the touch. Use a sharp knife to slice through the foam in straight lines, and throw away any rotten foam that you remove.
How long does it take for a repair resin board to dry?
To prevent the repair resin from trapping water and causing mold to form, set the board out and let it dry completely. After at least 6 hours, check that the board is dry, and inspect the crack. Before you begin working, squeeze the crack to make sure no water leaks out.
How to repair a ding in fiberglass?
Before beginning any type of ding repair be sure you put on a respiration mask and gloves. Safety goggles are also a good idea. #1 First make sure the dinged area is dry, no water droplets should be leaking out. You may have to cut back a little of the fiberglass using a knife to allow the foam to dry completely.
Is solar res better than fiberglass?
You are less “repairing” your board than you are “sealing” it, just to keep the water out. The advantage of solar res is that it is quick and easy to use, and is more compact to travel with than a traditional fiberglass repair.
Can you use epoxy to repair a fiberglass board?
It will contain everything you need to get the job done. Note that you can not use epoxy to repair a fiberglass board and visa-versa. If you have an epoxy surfboard, get an epoxy ding repair kit.
Is it empowering to repair a surfboard?
Repairing a surfboard or DIY ding repair as it is otherwise known, is definitely an empowering endeavor. Besides being empowering, there are other bonuses to learning how to repair a surfboard.
Is it better to repair a surfboard or buy a new one?
Learning how to repair a surfboard is WAY more environmentally friendly than buying a new factory-made surfboard. Surfboard manufacturing is not kind to the planet.
Can you repair a surfboard yourself?
The first time you learn how to repair a surfboard and do it yourself, you might use a solar resin. This is a specific resin that does not need to be mixed and hardens with exposure to the UV rays of the sun. You are less “repairing” your board than you are “sealing” it, just to keep the water out.
