- How to Repair a Hole in a Therm-a-Rest Sleeping Pad. Blow up the sleeping pad full of air using the intake valve in the top left corner. ...
- Fold the pad in half to increase the air pressure.
- Spray soapy water on the section of the pad where you think the hole is located.
- Look for small bubbles forming on the pad indicating the location of the hole. Mark the hole with a marker.
- Obtain a Therm-a-Rest repair kit including a packet of HotBond Adhesive, patch, and wood stick or similar.
- Boil water in a flat bottomed pan. Heat the HotBond Adhesive packet in the boiling water for three minutes.
- Tear off the end of the HotBond Adhesive packet. Squeeze the adhesive out of the packet onto the hole in the pad.
- Firmly press the patch, shiny side down, onto the HotBond Adhesive on the mattress. Place a layer of plastic, such as a plastic bag, over the patch.
- Remove the pan of water, and using a hard cylindrical object, such as a cup, roll over the patch a few times.
Can a thermarest mattress be repaired?
A Thermarest is just for sleeping. Teach your children never to stand or jump on an inflated sleeping pad. If you do end up with a leak, you can repair it easily by following these simple Thermarest repair instructions. Open the valve and let the mattress inflate. Blow in more air until it is very firm. Close the valve.
How do you fix a broken thermarest?
You can also do a Thermarest repair using urethane glue. Look for Freesole or Seam Grip. Here's what to do: Deflate the Thermarest completely and close the valve. Spread the urethane glue over the hole. Open the valve. This draws the glue into the hole, forming a long lasting seal. Let dry for at least 24 hours before using the Thermarest again.
Is it possible to clean a thermarest pad?
I have never had this happen - and I've never even known anyone who's had this happen - but if it does, you can buy a replacement valve kit. A Thermarest pad can be easily cleaned by wiping it with a damp cloth. Allow it to air dry.
How do you fix a hole in A Therm-a-rest couch?
Look for small air bubbles escaping from the pad into the water indicating the location of the hole. Obtain a Therm-a-Rest repair kit including a packet of HotBond Adhesive, patch, and wood stick or similar. Boil water in a flat bottomed pan. Heat the HotBond Adhesive packet in the boiling water for three minutes.
Can you repair a thermarest?
Send Your Sleeping Pad to the Pros to Repair If we find that there are punctures/tears in the mattress, we can repair those, but these are typically a wear-and-tear situation. We charge a flat-rate fee of $20 to repair a mattress.
How do you fix a hole in a sleeping pad?
1:045:11The 101: How to Fix a Sleeping Pad - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo once you locate the tear the first thing you're gonna want to do is use some of that seam grip orMoreSo once you locate the tear the first thing you're gonna want to do is use some of that seam grip or in this case the textile glue put it right over that.
How do you find a leak in a thermarest pad?
If you can't find the leak by sponging soapy water onto the pad, then submerge the pad....Pinpoint the Leak LocationFill the tub with water and add a small amount of soap.Inflate the pad.Sponge the soapy water onto the surface and watch for tiny bubbles to appear.Wipe and dry the spot, then mark it.
Can you repair sleeping pad with duct tape?
Step 3: Repair the Leak Using Whatever Is on Hand If the leak is somewhere in the pad itself, repairs can be a simple matter, if you have the right gear. You have 2 options: Duct Tape or Krazy Glue/GOOP Marine glue that will be readily available at most major stores.
Does Tenacious Tape work on thermarest?
It's easy to repair a Therm-a-rest, Big Agnes, Nemo, REI or other style sleeping pad with Tenacious Tape Flex Patches, or the Seam Grip WP Repair Kit. Fix the leak and get a good night's rest on your next camping trip. The first step in repairing your deflated sleeping pad is to find where the air is leaking.
How do I fix my pad?
Soldering the new pad/trace to the conductor: Use Kapton tape to place and hold the replacement pad. Use the appropriate solder alloy to make a lap joint. Clamping and curing: Clamp the new pad/trace in place and cure. Once cured, remove the clamp and clean the pad/trace with isopropyl alcohol.
How do you repair a leaking thermarest?
1:443:40Repairing Your Therm-a-Rest® Mattress - YouTubeYouTubeStart of suggested clipEnd of suggested clipApply repair adhesive directly to the puncture. Thoroughly work the adhesive into the fabric untilMoreApply repair adhesive directly to the puncture. Thoroughly work the adhesive into the fabric until you have a thin even layer that extends one inch beyond the puncture.
How do you find a hole in a camping pad?
0:482:53How to Identify & Repair a Leak in an Air Pad | NEMO - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can dunk the pad. And look for some bubbles to identify. Exactly where that leak is coming fromMoreYou can dunk the pad. And look for some bubbles to identify. Exactly where that leak is coming from step. Two is to clean.
How do I find a puncture in thermarest?
Look for small bubbles forming on the pad indicating the location of the hole. Mark the hole with a marker. If you cannot locate the hole with the soapy water, fill a bathtub with water, and submerge your pad. Look for small air bubbles escaping from the pad into the water indicating the location of the hole.
Will Gorilla tape patch an air mattress?
Is Gorilla tape good for an air mattress? Gorilla waterproof patch and seal tape works on vinyl and can be used similarly to duct tape. Do not add glue to the tape. Gorilla tape may damage the air mattress when removed, so don't use it if you plan to apply a patch kit later.
What household items can you use to patch an air mattress?
The easiest way to fix an air mattress is to glue a patch to the leaking area....You can use any thin plastic or rubber material for making a patch, for example:a piece of shower curtain;a pool liner;a piece of inner bike tire (the one that's made of soft rubber).
How do you fix a foam float pad?
1:092:50POOLCENTER.com - Texas Rec foam pool float chair Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe area and just fill it in real easily. And if the direction say you wet your fingertips. And getMoreThe area and just fill it in real easily. And if the direction say you wet your fingertips. And get a little water on there to smooth it out smooth out the edges.
How do you fix a foam float pad?
1:092:50POOLCENTER.com - Texas Rec foam pool float chair Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe area and just fill it in real easily. And if the direction say you wet your fingertips. And getMoreThe area and just fill it in real easily. And if the direction say you wet your fingertips. And get a little water on there to smooth it out smooth out the edges.
How do you fix a hole in a camping mattress?
1:322:28How to repair a self inflating mat | Innovative Family CampingYouTubeStart of suggested clipEnd of suggested clipOnce you're ready to apply the patch. It's as simple as applying a sticker apply the pets to theMoreOnce you're ready to apply the patch. It's as simple as applying a sticker apply the pets to the fabric. And make sure that the pet is fully glued to the fabric.
How do you repair klymit pads?
0:187:05How to find and fix a leak in your sleeping pad - Klymit Xlite - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what I recommend is you pump this up completely and give it a good high pressure. Now when you'reMoreSo what I recommend is you pump this up completely and give it a good high pressure. Now when you're pumping up this pad make sure it's not locked it's pressed down but it's not locked because.
How do you fix exped mats?
2:023:02Exped Tip: How do I fix the hole in my mat myself? (English subtitles)YouTubeStart of suggested clipEnd of suggested clipVor. Auf diese art und weise ist er mathe bald wieder dicht oder reparatur ist kaum zu sehen.MoreVor. Auf diese art und weise ist er mathe bald wieder dicht oder reparatur ist kaum zu sehen.
How to seal a thermometer?
Here's what to do: Deflate the Thermarest completely and close the valve. Spread the urethane glue over the hole. Open the valve. This draws the glue into the hole, forming a long lasting seal. Let dry for at least 24 hours before using the Thermarest again.
How to fix a hole in a mattress?
Put some water and a squirt of dish soap into a bowl. Spread this soapy water over the area where you suspect a hole. Fold the mattress to force out air, and watch for bubbles. There's your hole! Circle the hole with a pen. Turn the pad over and check the other side too. Rinse off the so ap.
What is a self inflating mattress?
What is a self-inflating sleeping pad? A self inflating sleeping pad consists of a foam core inside a durable shell. When its valve is opened, the mattress fills with air. These mattresses can ensure you a great night's sleep even when you are sleeping right on the ground.
What bag do you put mattresses in for camping?
For car camping, we carry our mattresses in a large duffle bag.
How long does it take for the thermometer to dry?
Let dry for at least 24 hours before using the Thermarest again.
Do you need to know about Thermarest repair?
You'll probably never need to know about Thermarest repair - but I'll tell you how to do it, just in case!
Can you store thermometers when they are damp?
Be sure that your Thermarest is completely dry before you store it away. If you store it when it's damp, you risk mildew.
How to tell if a hole is in a pad?
Look for small bubbles forming on the pad indicating the location of the hole.
How to increase air pressure on a sandpaper pad?
Fold the pad in half to increase the air pressure .
How to apply hotbond adhesive to mattress?
Firmly press the patch, shiny side down, onto the HotBond Adhesive on the mattress.
How to spread adhesive with wood stick?
Spread the adhesive with the wood stick until the adhesive is spread in an even circular layer approximately the size of a dime.
How long to boil hotbond adhesive?
Heat the HotBond Adhesive packet in the boiling water for three minutes.
What is the maximum liability of theRM-a-rest?
THERM-A-REST’S MAXIMUM LIABILITY IS LIMITED TO INCIDENTAL DAMAGES NOT TO EXCEED THE ORIGINAL PURCHASE PRICE OF THE PRODUCT. THERM-A-REST DISCLAIMS AND EXCLUDES ANY LIABILITY FOR ANY CONSEQUENTIAL OR OTHER DAMAGES RESULTING FROM ANY REASON WHATSOEVER. THIS EXCLUSION AND LIMITATION APPLIES TO ALL LEGAL THEORIES UNDER WHICH DAMAGES MAY BE SOUGHT, AND WILL APPLY EVEN IF ANY REMEDY FAILS OF ITS ESSENTIAL PURPOSE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. EXCLUDING THE LIMITED WARRANTY PROVIDED ABOVE, THERM-A-REST AND ITS AFFILIATES MAKE NO WARRANTIES, EXPRESSED OR IMPLIED; AND NO WARRANTIES WHICH EXTEND BEYOND ANY MANUFACTURER SUPPLIED DESCRIPTION ACCOMPANYING THE PRODUCT. THE REMEDIES ABOVE ARE YOUR SOLE AND EXCLUSIVE REMEDIES AGAINST THERM-A-REST AND ITS AFFILIATES, REGARDLESS OF LEGAL THEORY. SHOULD A COURT FIND THIS LIMITED WARRANTY BREACHED, THERM-A-REST’S ONLY OBLIGATION WILL BE, AT ITS OPTION, TO EITHER REPAIR OR REPLACE PRODUCT. SHOULD A COURT FIND THIS LIMITED WARRANTY TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, THERM-A-REST WILL REFUND TO YOU THE PRODUCT’S ORIGINAL PURCHASE PRICE.
Is shipping to an authorized repair center covered by the warranty?
Shipping charges to an Authorized Repair Center for a damaged product are not covered and are the responsibility of the customer. Return shipping charges for the repaired product will be covered.
Can you repair thermo-a-rest?
Our products are built to withstand the rigors of a life outside and we stand behind the quality of every product we make. If you need to repair a Therm-a-Rest product, we will do everything we can to repair or warranty it as quickly as possible.
Is therm a rest covered by the Better Sleep Guarantee?
Therm-a-Rest sleeping bags are covered under the Better Sleep Guarantee. When you wake up on a Therm-a-Rest sleeping bag, we're confident you'll wake up feeling better than ever. If you are not completely satisfied with your sleeping bag, return it within three months with the original receipt of purchase and we will give you a full refund- no questions asked.
How to open a sleeping pad valve cap?
Unroll your sleeping pad and open the valve cap by twisting it counter-clockwise.
How to protect NeoAir mattress from dirt?
NeoAir: We recommend leaving the valve open and storing your mattress rolled tight in a stuff sack to protect it from dirt and sharp objects.
Why don't self inflation pads inflate?
Self-inflation begins when the valve is opened and ends when equilibrium is reached between the atmospheric pressure outside the cells and the air pressure within the cells pushing the other way. In our experience, most users’ comfort level requires more air than the equilibrium level, which is why self-inflating pads don’t inflate “all the way.” Check out our blog post for more information.
What is self inflating sleeping pad?
Self-inflating sleeping pads rely on the compressible and rebound-able open cell foam cores to self-inflate. The atmospheric pressure around the pad pushes air into the rebounding open cells when the valve is opened. Check out our blog post for more information.
What is a permanent home repair kit?
The Permanent Home Repair Kit uses a wet adhesive and fabric patches to make the strongest and most durable Therm-a-Rest ® mattress repairs possible. It is also the best choice for repairing larger tears. Works on all Therm-a-Rest mattresses, including NeoAir. *Requires a 4-hour cure time.
What is ASTM F3340-18?
ASTM F3340-18 is a new testing standard that provides R-value ratings for sleeping pads. While Therm-a-Rest has always used R-value to rate our sleeping pads, this new standardization will allow campers to make “like-for-like” comparisons with our competitors pad. Head to a blog for an in-depth explanation.
Can you self inflate a mattress?
Self-Inflating: We recommend storing the mattress unrolled and fully inflated in a dry place with the valve open. This will ensure the foam self-inflates faster when camping. Storage for a prolonged time in a damp space may cause mildew damage which is not covered by our Limited Lifetime Warranty.
What to do if your pad doesn't work?
If your repair didn’t take, then it’s time to contact a professional. First, check with the company that made your pad. If your pad manufacturer doesn’t do repairs, they can suggest a service that does.
How to find a leak in a pad?
If you can’t find the leak by sponging soapy water onto the pad, then submerge the pad. Squeeze it gently as you methodically check for leaks in different areas of the pad.
How to patch a seam grip?
Cut a section of Tenacious Tape, ensuring that it precisely covers the Seam Grip. Trim (round off) the corners of your cut section, then put a thin line of Seam Grip all around the perimeter of the patch (that helps prevent peeling edges later). Check to see that the Seam Grip is slightly tacky. Firmly apply the patch.
What to do if a leak is so small?
If the leak is so small you can’t pinpoint its location, then a full repair is a home project. (The temporary field repair is simply to reinflate your pad periodically.) To sleuth out the leak location at home, you’ll need:
How to find a micro leak in a bathtub?
The following steps will help you find an elusive micro-leak: Fill the tub with water and add a small amount of soap. Inflate the pad. Sponge the soapy water onto the surface and watch for tiny bubbles to appear. Wipe and dry the spot, then mark it.
How to open a sleeping pad valve cap?
Unroll your sleeping pad and open the valve cap by twisting it counter-clockwise.
How to protect NeoAir mattress from dirt?
NeoAir: We recommend leaving the valve open and storing your mattress rolled tight in a stuff sack to protect it from dirt and sharp objects.
What is self inflating sleeping pad?
Self-inflating sleeping pads rely on the compressible and rebound-able open cell foam cores to self-inflate. The atmospheric pressure around the pad pushes air into the rebounding open cells when the valve is opened. Check out our blog postfor more information.
Why don't self inflation pads inflate?
Self-inflation begins when the valve is opened and ends when equilibrium is reached between the atmospheric pressure outside the cells and the air pressure within the cells pushing the other way. In our experience, most users’ comfort level requires more air than the equilibrium level, which is why self-inflating pads don’t inflate “all the way.” Check out our blog postfor more information.
What is ASTM F3340-18?
ASTM F3340-18 is a new testing standard that provides R-value ratings for sleeping pads. While Therm-a-Rest has always used R-value to rate our sleeping pads, this new standardization will allow campers to make “like-for-like” comparisons with our competitors pad. Head to a blog for an in-depth explanation.
Can you self inflate a mattress?
Self-Inflating: We recommend storing the mattress unrolled and fully inflated in a dry place with the valve open. This will ensure the foam self-inflates faster when camping. Storage for a prolonged time in a damp space may cause mildew damage which is not covered by our Limited Lifetime Warranty.
Can you put a mattress in the washing machine?
Do not put your mattress in the washing machine. Cleaning with a hose or in a bathtub is best. Do not forget to close the valve while washing. For general cleaning, a quick scrubbing with Formula 409®, BioClean™All-Purpose Cleaner, or other general household cleaner is best.
