How To Fix A Troy Bilt Weed Eater
- Clean The Air Filter. Use a flat blade or screwdriver to unscrew the screws with the air filter cover in place. ...
- Clean The Spark Plug. You have to wait for the trimmer engine to cool. ...
- Adjust The Carburetor. Start your trimmer engine. ...
- Fuel Filter Clog. ...
- Replace your Troy-built Weed Eater carburetor. ...
Full Answer
Can you repair a Troy Bilt weed trimmer?
You can repair your weed trimmer. Many of the problems you encounter while using a Troy-Bilt weed trimmer can be attributed to a dirty air filter, a bad spark plug or a poorly adjusted carburetor. Some of the problems they can cause include the trimmer not idling properly, the engine not starting and the engine stalling while in use.
How do you fix a clogged spark plug in a trimmer?
Take care not to tighten it too much. Replace the spark plug wire by pushing onto the plug until it snaps in place. Start the trimmer's engine and run it at a high idle to allow it to warm up. Let the trimmer's throttle go.
How to fix a trimmer that stops and then starts and stops?
However, if your trimmer starts and stops, you may need to check and replace it sooner. To change the fuel filter, first, drain the fuel. You should be able to pull the fuel line and filter out through the gas tank opening. After that, you can swap the filter for a clean one and put it back.
How do you change the spark plug on a husky Trimmer?
Replace the spark plug wire by pushing onto the plug until it snaps in place. Start the trimmer's engine and run it at a high idle to allow it to warm up. Let the trimmer's throttle go. If the engine stops, use a #1 Phillips screwdriver to adjust the idle speed screw in the air filter cover.
What is the cause of trimmer head not spinning?
0:051:30Top Reasons String Trimmer Head Not Spinning - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe clutch engages one or more drive shafts which attach to the trimmer head. If the clutch assemblyMoreThe clutch engages one or more drive shafts which attach to the trimmer head. If the clutch assembly is worn-out the trimmer head won't spin a new clutch assembly is relatively inexpensive.
How do you fix a trimmer that won't start?
0:542:58Top Reasons String Trimmer Not Starting - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can try cleaning the carburetor with carburetor cleaner to eliminate the clog. If cleaning isMoreYou can try cleaning the carburetor with carburetor cleaner to eliminate the clog. If cleaning is not effective you can often purchase a carburetor repair kit to replace some of the components.
Why won't my Weedeater keep running?
Most weed eaters will have a small air hole available on the cap to the gas tank – This lets air into the tank to help prevent any vacuum from forming. An easy way to check if your air hole is clogged is to simply loosen the cap while the trimmer is running – If performance improves, a replacement gas cap is your fix.
Why is my gas Weedeater not starting?
A gasoline-powered weed trimmer that won't start may have a fuel-related problem. First and foremost, check whether or not enough fuel to power the trimmer is in its fuel tank. If the fuel level is low, the trimmer may not start. Fill the tank, and try to start the trimmer.
How do I fix my lawn trimmer?
0:259:22How to FIX Your LAWN TRIMMER: Common Issues and How to Repair ...YouTubeStart of suggested clipEnd of suggested clipWith the wrench in place the head is now locked and i can unscrew it on a straight shaft trimmer theMoreWith the wrench in place the head is now locked and i can unscrew it on a straight shaft trimmer the thread will be a reverse thread a curved shaft will have a regular.
Why does my gas trimmer keeps stalling?
0:042:00Top Reasons String Trimmer Starting, Then Stalling - YouTubeYouTubeStart of suggested clipEnd of suggested clipOver time the arrestor can become clogged with soot which may cause the trimmer engine to stall. YouMoreOver time the arrestor can become clogged with soot which may cause the trimmer engine to stall. You can try cleaning the arrestor with a wire brush. But you may need to replace it with a new.
Why does my Weedeater only run on choke?
Why Does My Weed Eater Only Run on Full Choke? (The Short Answer) The main reason why a weedeater only runs on full choke is because of issues with the air and fuel supply due to a dirty carburetor, a bad gas cap vent, or a clogged fuel filter.
How do you adjust a Weedeater carburetor?
2:075:55HOW TO ADJUST The Carburetor on Weedeater XT260 Grass TrimmerYouTubeStart of suggested clipEnd of suggested clipOn these weed eaters is that the high screws here low screws there you adjust this screw here atMoreOn these weed eaters is that the high screws here low screws there you adjust this screw here at high speeds revving your machine up this one here you adjust it when it's idling.
How do you adjust a carburetor?
0:412:42How To Adjust A Carburetor On Your Car - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd all you need is a screwdriver on the front turn it to the left makes it go slower turning to theMoreAnd all you need is a screwdriver on the front turn it to the left makes it go slower turning to the right makes it go faster. So with the engine running turn the screw. So it idles decently.
Why isn't my primer bulb won't fill up?
Another cause of the primer's filling problem could be the bulb itself. Small perforations on the rubber could inject enough air into the fuel system to make the suction too weak. Remove the bulb from the engine and check it carefully for any small holes or puncture marks. Replace any worn or cracked bulbs.
Why is my primer bulb not working?
When the primer bulb isn't working, it may be a problem with the bulb itself, with the fuel lines that feed fuel to the bulb or both. Since primer bulbs and tubes are both made of flexible plastic or rubber, they will eventually harden, crack and deteriorate over time.
How do you Unflood a trimmer?
How to Unflood a String TrimmerStep 1: Open the Choke. Set the choke to the "off" position. ... Step 2: Hold In the Throttle. Depress the throttle all the way as if you were operating the trimmer at full speed.Step 3: Quickly Pull the Cord Several Times.
Why has my strimmer stopped working?
The most common problem with a string trimmer is that the unit runs out of string. The string may also be twisted or loose on the spool. The cutting head may be dirty or the head outlet guide may be bent. An electric trimmer's power cord, switch, or motor may fail.
How do you start a string trimmer?
1:464:18Starting a Gas String Trimmer - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou want to place the choke lever to the cold start position on a cold start you push the purgeMoreYou want to place the choke lever to the cold start position on a cold start you push the purge valve five to six times making sure that it's filled with fuel. So now you're ready to pull the recoil.
How often should I change spark plug on Weedeater?
As a general rule, you should change the spark plug approximately every 100 hours. This may vary across brands and specific models. Check your Owner's Manual for specific information on how often to change the spark plug and the proper gap setting. Check the grease/oil in the cutting head gearbox often.
How do I fix my Ryobi trimmer?
1:407:54How to Repair Your 18v Ryobi String Trimmer - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you don't have one of these doesn't matter pocketknife or something. But you need to get theMoreIf you don't have one of these doesn't matter pocketknife or something. But you need to get the insulation off of the wire end. And so and then just kind of twist it. Around.
Why is my Troy Bilt weed trimmer not starting?
Many of the problems you encounter while using a Troy-Bilt weed trimmer can be attributed to a dirty air filter, a bad spark plug or a poorly adjusted carburetor. Some of the problems they can cause include the trimmer not idling properly, the engine not starting and the engine stalling while in use. Fortunately, cleaning the filter, replacing the ...
How to remove spark plug from a chevy sprite?
Step 1: Remove the Spark Plug Wire. Wait for the trimmer's engine to cool. Once the engine is cool, find the spark plug on the trimmer's cylinder head. Grasp the spark plug wire and pull it to remove it from the spark plug. Advertisement.
Troy Bilt Trimmer Starts And Dies
The trouble of starting and stopping trimmers is not uncommon, nor is it exclusive to Troy Bilt. There are quite a few things that can lead to this particular problem.
Helpful Tips To Know About Why Troy Bilt Trimmer Starts And Dies
Repairing most of the problems that cause your trimmer to die right after it starts is incredibly easy. Often you won’t need more than a screwdriver and a new part.
Final Thoughts
String Trimmers are essential for keeping your yard looking nice. Since Troy Bilt, Craftsman, and several others have compatible accessories, you’ll have no trouble getting everything the way you like it, so long as you can get the trimmer to stay on.