Repairing Guides

how to repair a victor cutting torch

by Miss Maybelle Hammes Sr. Published 2 years ago Updated 2 years ago
image

Brush the torch tip thoroughly with a wire brush to remove any debris or metal particles. If the torch tip is warped or flattened on the end, replace with a new tip. Clean the inside of the torch tip port holes with a torch tip cleaning tool.

Full Answer

How much does it cost to rebuild a Victor torch?

Victor ST900C & ST900FC Cutting Torch Rebuild/Repair Parts Kit 4.7 out of 5 stars 7 1 offer from $19.99 Victor CA2460 & CA2470 Cutting Torch Rebuild/Repair Parts Kit, with 1-1-101 Tip 4.5 out of 5 stars 42 Amazon's Choice in Gas Welding Torches 1 offer from $24.99 Victor CA2460 & CA2470 Cutting Torch Rebuild/Repair Parts Kit

How do you clean the tip of a torch?

Check the torch tip for clogged ports. Brush the torch tip thoroughly with a wire brush to remove any debris or metal particles. If the torch tip is warped or flattened on the end, replace with a new tip. Clean the inside of the torch tip port holes with a torch tip cleaning tool.

What causes a torch tip to go bad?

Most problems that happen in the torch tip involve the tip nut not being tightened down properly, damaged O-ring or clogged port holes. If the port holes are clogged, it will prevent the proper amount of acetylene and oxygen from flowing out of the torch tip.

What is a cutting torch used for?

The purpose of a cutting torch is to cut through various sizes of metals. Most torch problems and complaints come from the torch tip and from the O-rings that seal the nuts.

image

How do you fix a cutting torch?

Check the torch tip for clogged ports. Brush the torch tip thoroughly with a wire brush to remove any debris or metal particles. If the torch tip is warped or flattened on the end, replace with a new tip. Clean the inside of the torch tip port holes with a torch tip cleaning tool.

How do you rebuild a cutting torch head?

1:495:22How to Repair A Victor 2460/Large Torch | Eagle Welding SupplyYouTubeStart of suggested clipEnd of suggested clipSo first off you want to start off with all brand new. Parts. This stem you'll start off with thisMoreSo first off you want to start off with all brand new. Parts. This stem you'll start off with this you'll push it into the retainer.

How do you clean a victor cutting torch?

3:189:40Oxy-fuel torch set up cleaning, preventative maintenance, and careYouTubeStart of suggested clipEnd of suggested clipWe also want to make sure they're tight but the first thing I'm going to do is I'm going to scrapeMoreWe also want to make sure they're tight but the first thing I'm going to do is I'm going to scrape this tip off or anything that's on there and I'm going to push the oxygen lever while I'm doing that.

How do you rebuild a victor regulator?

3:296:46Victor Oxygen Regulator Rebuild - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust like that that piece of nylon just helps it slide in and out of there keeps it aligned. ItMoreJust like that that piece of nylon just helps it slide in and out of there keeps it aligned. It doesn't look like it's down in that cup good there it. Goes. There that's better.

How can a cutting torch tip seal be repaired?

How can cutting torch tip seals be repaired? By using a reamer designed for the specific torch tip and head, or new fiber packings are available for tips with packings, or it can be sent out for repair.

How do you unclog a tip torch?

1:474:46How to Clean Your Oxygen-Acetylene Tips - Kevin Caron - YouTubeYouTubeStart of suggested clipEnd of suggested clipFit it's not too tight it's not too loose. And you just slide it through and clean all the littleMoreFit it's not too tight it's not too loose. And you just slide it through and clean all the little tips out all the little orifices.

What does it mean if the flame is jumping off the tip of the torch?

If you cannot get rid of the smoke with the oxygen valve all the way open, you need to increase the oxygen line pressure at the regulator. If the yellow flame jumps off the tip BEFORE the smoke disappears, your tip is dirty!

How much is a torch tip?

Compare with similar itemsThis item Acetylene Cutting Tip 3-101#000, 3-101-000 for Victor TorchAcetylene Cutting Tips 3-101 Size 0 for Victor Style Torch 2pkCustomer Rating4.4 out of 5 stars (65)4.5 out of 5 stars (261)Price$899$11.00$11.00Sold ByWeldingCityRIVERWELDstoreCompatible Devicesacetyleneacetylene3 more rows

What is backfiring in welding?

The momentary recession of the flame into the torch, potentially causng a flashback or sustained backfire. It is usually signaled by a popping sound, after which the flame may extinguish or reignite at the end of the tip.

Can gas regulator be repaired?

When we perform repairs and/or maintenance, we fully disassemble the regulator, clean and check all internal and external components for wear or corrosion, and reassemble the equipment with any necessary replacement parts.

How do you fix an oxygen regulator?

0:101:27Fitting a Regulator & Flowmeter to a Gas Cylinder - DemonstrationYouTubeStart of suggested clipEnd of suggested clipHead. When attaching your regulator align the locating pins on the regulator to the correspondingMoreHead. When attaching your regulator align the locating pins on the regulator to the corresponding holes located on the cylinder head and tighten the wing screw.

How do you fix a acetylene regulator?

1:386:35Quick & Dirty: Acet Reg Rebuild - YouTubeYouTubeStart of suggested clipEnd of suggested clipI go with mucking around with it a bit more drain off all the acetylene out of there. And. We'reMoreI go with mucking around with it a bit more drain off all the acetylene out of there. And. We're gonna fix this so make sure the tank is closed back off the regulator.

How do you rebuild a nitrogen regulator?

0:552:11How to Repair a Nitrogen Regulator - Inside Look at Taprite RegulatorYouTubeStart of suggested clipEnd of suggested clipThis groove will need to align with the ball that is in the center of the regulator body begin byMoreThis groove will need to align with the ball that is in the center of the regulator body begin by sliding it down from the top until you find the groove. And center it on the regulator.

Why is my oxygen regulator hissing?

A hissing sound means gas is coming out. Stop once you hear the hissing sound, and turn the valve off by turning it to the right (clockwise). Don't over tighten. Always be sure the valve, regulator, and sealing washer are free of oil or grease.

What should torch regulators be set at?

4:506:59How to set the oxy acetylene regulators - YouTubeYouTubeStart of suggested clipEnd of suggested clipOkay think of the two numbers ten. And five always my oxygen should be at a higher pressure than myMoreOkay think of the two numbers ten. And five always my oxygen should be at a higher pressure than my settling may rot want to run that thing up to 12 or 13 something like that.

What is oxygen regulator?

Oxygen regulators are intended for the administration of oxygen to patients that are deemed by a physician to need increased oxygen levels to improve or stabilize their breathing conditions. It is a pressure-reducing device that lowers the pressure of the oxygen from a cylinder to a level that can safely be used.

What is the purpose of a cutting torch?

The purpose of a cutting torch is to cut through various sizes of metals. Most torch problems and complaints come from the torch tip and from the O-rings that seal the nuts. Over time, the ports inside the tip will develop blockage from metal particles and other debris and the O-rings will wear out. The torch can also malfunction ...

How to disconnect the top half of a torch from the bottom half?

Disconnect the top half of the torch from the bottom half by turning the screw-on nut counterclockwise. Pull the two sections apart. Look to see if the nut has an O-ring. If so, check the condition of the O-ring and replace if necessary.

How to check if a torch tip is clogged?

Check the torch tip for clogged ports. Brush the torch tip thoroughly with a wire brush to remove any debris or metal particles. If the torch tip is warped or flattened on the end, replace with a new tip.

What happens if the tip of a torch is clogged?

If the port holes are clogged, it will prevent the proper amount of acetylene and oxygen from flowing out of the torch tip. Advertisement.

How to reattach oxygen hose to pressure gauge?

Reattach the acetylene and oxygen hoses to the pressure gauges on each supply tank. Tighten the nuts, then open the valves to both pressure gauges. Turn the acetylene knob and light the tip of the torch with the striker. Test-cut a piece of metal to ensure that the torch is working properly .

Victor cutting torches (old) leak at nozzle..

I was recently able to purchase some Victor equipment at a very reasonable price. However, on trying the two cutting torches with the available nozzles, I found both to leak at the threads of the nut attaching the nozzle.

Leaking torch tip

Many torches needing reaming (quick repair at weld repair place) after being used incorrectly. Torch tips are cooled by the gas going flowing through them. When a torch is throttled down too far the tip gets hot and warps the torch head. Then when a new torch tip is installed it leaks. If you need less heat then switch to a smaller tip.

Special offers and product promotions

Create your FREE Amazon Business account to save up to 10% with Business-only prices and free shipping. Register today

Have a question?

There was a problem completing your request. Please try your search again later.

Top reviews from the United States

There was a problem filtering reviews right now. Please try again later.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9